CAUTION: Danger of explosion if battery is incorrectly replaced. When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Laser compliance statement Some IBM Personal Computer models are equipped from the factory with a CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold separately as options. CD-ROM drives and DVD-ROM drives are laser products.
Page 10
DANGER Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. DANGER: Certains modèles d’ordinateurs personnels sont équipés d’origine d’une unité de CD-ROM ou de DVD-ROM. Mais ces unités sont également vendues séparément en tant qu’options.
Information resources Access IBM, on your desktop, provides a link to more information about your computer. If you have Internet access, the most up-to-date manuals for your computer are available from the World Wide Web. To access this information, point your browser http://www.ibm.com/pc/support...
Before you install any option, read “Safety Information” on page v. These precautions and guidelines will help you work safely. See Access IBM for general information about the use, operation, and maintenance of your computer. Access IBM also contains information to help you solve problems and get repair service or other technical assistance.
Features This section provides an overview of the computer features, preinstalled software, and specifications. Not all models come with all features that are summarized here. Microprocessor ® ™ ™ Intel Pentium 4 with 256 KB of internal L2 cache memory and MMX technology Memory v Support for Rambus in-line memory modules (RIMMs)
Page 15
1. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.
IBM OS/2 Warp Connect 3.0 v IBM OS/2 Warp 4.0 v IBM OS/2 LAN Server 3.0 and 4.0 v Linux: Red Hat, Caldera, SuSE, and Turbo Linux Specifications This section lists the physical specifications for the NetVista computer. Your computer has five 32-bit PCI expansion slots, one AGP slot, and seven drive bays.
Page 17
Dimensions Heat output (approximate) in British thermal units (Btu) per hour: Height: 165 mm (6.5 in.) Minimum configuration: 240 Btu/hr (75 watts) Width: 445 mm (17.5 in.) Maximum configuration: 940 Btu/hr (275 watts) Depth: 499 mm (19.6 in.) Airflow Weight Approximately 0.34 cubic meters per minute (12 cubic Minimum configuration as shipped: 14.0 kg (30 lb) feet per minute) maximum...
Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-465-7999. v Outside the United States and Canada, contact your IBM reseller or IBM marketing representative. Tools required To install some options in your computer, you might need a flat-blade screwdriver.
Page 19
v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds.
Locating the connectors on the rear of your computer The following illustration shows the location of the connectors on the rear of the computer. Your computer might not have all of the connectors shown here. 1 Power connector 9 LEDs 2 Mouse connector 10 Ethernet connector 3 Keyboard connector...
Connector Description Ethernet connector Used to attach an Ethernet cable that uses an Ethernet connector. Note: To operate the computer within FCC Class A or Class B limits, use a category 5 Ethernet cable. Microphone connector Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech-recognition software.
The following illustration shows the connectors on the high-performance audio adapter that comes with some models. Connector Description 1 MIDI/joystick connector Used to attach a joystick, gamepad, or a musical instrument digital interface (MIDI) device such as a MIDI keyboard. 2 Audio line out connector Used to send audio signals from the computer to external devices, such as powered stereo speakers (speakers with built-in amplifiers), headphones,...
Check your ISP access agreement for more information. Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device driver files. Chapter 2. Installing external options...
Identifying parts on the system board The system board, also called the planar or motherboard, is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later. User Guide...
Your computer has four connectors for Rambus in-line memory modules (RIMMs) that provide up to a maximum of 2 GB of system memory. The IBM-installed RIMMs that come with your computer are ECC (error checking and correction) Rambus dynamic random access memory (RDRAM) modules.
Page 30
v Each RIMM connector supports a maximum of 512 MB of memory. v Any connector that does not have a RIMM installed must have a continuity RIMM (C-RIMM), a module that looks like a RIMM but has no memory on it. A C-RIMM is used to continue the connection on a RIMM connector that does not have memory installed in it.
2. If the retaining clips are not already open, open them. 3. Position the RIMM or C-RIMM above the connector so that the two notches on the bottom edge of the module align properly with the empty connector. 4. Firmly push the module straight down into the connector until the retaining clips pop up and fit snugly around both ends of the module.
Page 32
2. Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter slot cover latch. User Guide...
Also, it is important to correctly connect the internal drive cables to the installed drive. Drive specifications Your computer comes with the following IBM-installed drives: v A CD drive or DVD drive in bay 1 (some models) v A 3.5-inch hard disk drive in bay 3 v A 3.5-inch diskette drive in bay 4...
The following illustration shows the locations of the drive bays. The following table describes some of the drives you can install in each bay and their height requirements. 1 Bay 1 - Maximum Height: 41.3 mm (1.6 in.) CD-ROM drive (standard in some models) 5.25-inch hard disk drive 2 Bay 2 - Maximum Height: 41.3 mm (1.6 in.) 5.25-inch hard disk drive...
Page 35
v Flat signal cables, also called ribbon cables, connect IDE and diskette drives to the system board. There are two sizes of ribbon signal cables that come with your computer: – The wider signal cable has two or three connectors. - If the cable has three connectors, one of these connectors is attached to the drive, one is a spare, and the third is attached to the primary or secondary IDE connector on the system board.
Installing internal drives in bays 1, 2, and 3 To install an internal drive in bay 1, 2, or 3: 1. Remove the cover (see “Removing the cover” on page 15). Note: If your computer has a CD drive or DVD drive, you might need to remove the signal and power cables from the drive.
3. Install the drive into the bay. Align the screw holes, and insert the two screws. 4. If the drive that you installed is a removable-media drive, place the bezel frame that comes with your computer over the drive bay. 5.
Page 38
2. Remove the support bar by pulling it outward from the computer as shown. 3. Pull and pivot the lower drive-bay cage outward from the computer. User Guide...
Page 39
4. Mount sliding rails on the drive that you want to install, and slide the drive along the rail guides into the unoccupied drive bay. 5. Pivot the drive bay cage back into place. Chapter 3. Installing internal options...
6. Connect the power and signal cables to the drive. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 29. Installing a security U-bolt To help prevent hardware theft, you can add a security U-bolt and cable to your computer.
1 U-bolt 2 Bolt holes 3 Nuts What to do next: To work with another option, go to the appropriate section. Replacing the cover and connecting the cables After working with options, you need to install any removed parts, replace the cover, and reconnect any cables, including power cords and telephone lines.
Page 42
3. Position the cover on the chassis and slide the cover toward the front bezel of the computer. Make sure to align the tabs on the computer with the cover. 4. Close the cover-release latch to secure the cover in place. 5.
(if required, after a new option has been installed), and erasing a lost or forgotten password. For more information about using the BIOS Setup Utility program, see Access IBM. After you add options, the configuration settings must be updated. In most cases, this configuration update is performed automatically.
Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see Access IBM. To erase a forgotten password: 1. Turn off the computer and all attached devices.
Page 45
11. Select Exit Saving Changes. 12. Follow the directions on the screen. Note: You must remove the cover again to place the jumper to the normal setting. Chapter 4. Updating the computer configuration...
POST, BIOS, and the BIOS Setup Utility program by starting your computer using a flash update diskette. IBM might make changes and enhancements to the system programs. When updates are released, they are available as downloadable files on the World Wide Web (see the Quick Reference).
Page 50
7. Locate the Clear CMOS/Recovery jumper on the system board, removing any adapters that impede access to the jumper. See the system board label inside your computer for the location of the jumper. See also “Identifying parts on the system board” on page 16. 8.
Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: NetVista OS/2...
Page 60
video (continued) controller 2 User Guide...
Page 62
Part Number: 06P8666 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber. (1P) P/N: 06P8666...