Kwikset Smartcode 914 Programming And Troubleshooting Manual
Touchpad
Hide thumbs
Also See for Smartcode 914:
- Installation manual ,
- User manual (26 pages) ,
- Programming and troubleshooting manual (17 pages)
Advertisement
Table of Contents
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Kwikset Smartcode 914
Summary of Contents for Kwikset Smartcode 914
- Page 1 61883 / 01 Programming and Troubleshooting Guide Master Code Troubleshooting: Installation Troubleshooting: Door Jamming and Door Handing Troubleshooting: Keypad Troubleshooting: Battery Battery FAQ Technical Support 1 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
-
Page 2: Enabling And Setting The Master Code
6. Make sure switch #3 is on, and press the Program button once. If you hear three beeps and see the keypad flash green three times, the Master Code is enabled. Technical Support 2 / 13 ©2014 Kwikset Corporation 1-866-863-6584... -
Page 3: Adding User Codes With The Master Code Enabled
Make sure to enter a valid Master Code in step 2. 6. While the door is open, test the user code to make sure it unlocks the door. Technical Support 3 / 13 ©2014 Kwikset Corporation 1-866-863-6584... - Page 4 2. Press Lock button once. 7. Re-enter user code to be deleted. 3. Enter Master Code. 8. Press Lock button once. 4. Press Lock button once. Procedure continued on next page Technical Support 4 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
- Page 5 4. Press Lock button once. will hear three beeps. 5. Press “9” six times. 2. Press Lock button once. 6. Press Lock button once. 3. Enter Master Code. Procedure continued on next page Technical Support 5 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
- Page 6 Make sure to enter a valid Master Code in step 3 during your next attempt. 9. Press the Lock button while the door is open. If the latch bolt does not extend to lock, then all codes have been successfully deleted. Technical Support 6 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
-
Page 7: Troubleshooting: Installation
If the word “UP” is upside down and at the bottom of the latch, the latch is installed incorrectly. Reinstall the latch, making sure the word “UP” faces upward. Technical Support 7 / 13 ©2014 Kwikset Corporation 1-866-863-6584... -
Page 8: Troubleshooting: Door Jamming And Door Handing
If the latch being used is from an older lock, it will likely not have a tapered latch bolt. Remove the lock from the door, including the old latch. Replace with the new tapered latch that came with the lock and reinstall the lock. Technical Support 8 / 13 ©2014 Kwikset Corporation 1-866-863-6584... - Page 9 Make sure the latch bolt can operate smoothly with the key and reinstall the interior assembly. Technical Support 9 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
- Page 10 If it is successful only when the door is open, the latch and strike are not aligned as they should be. Ensure door preparation is in accordance with the door drilling instructions, available online. Technical Support 10 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
- Page 11 If it is successful only when the door is open, the latch and strike are not aligned as they should be. Ensure door preparation is in accordance with the door drilling instructions, available online. Technical Support 11 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
- Page 12 See page 9. Perform the door handing process, following the instructions inside the installation guide. The battery is too low to lock the door. Remove the batteries and replace with a fresh set. Technical Support 12 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
-
Page 13: Troubleshooting: Battery
Will my lock operate when I get back? When the system is idling, it consumes minimum power (very close to battery shelf life.) With alkaline batteries, the lock should be operable after years of idle. Technical Support 13 / 13 ©2014 Kwikset Corporation 1-866-863-6584...
Need help?
Do you have a question about the Smartcode 914 and is the answer not in the manual?
Questions and answers