Kwikset 914CZigBee C4 Installation And User Manual

Kwikset 914CZigBee C4 Installation And User Manual

Full lock

Advertisement

Quick Links

66494-002
Rev 02
914C ZigBee® C4
Full Lock
Signature Series Deadbolt
with Home Connect
Installation and User Guide
Kit "A"
Kit "B"
Black mounting
Gold mounting
plate
plate
Black adapter
A1
X1
Interior assembly
screws
Mounting
Mounting
D
plate screws
plate screws
A2
Interior cover
screws
A3
E
1

Full smart lock vs interior conversion kit

This package contains a full smart lock set as well as interior
parts that can be used with your existing deabolt exterior
to convert your mechanical lock into a smart lock.
The following steps will show you how to install the full smart
lock set. If you are installing the interior conversion kit, please
refer to the other instruction sheet in the package.
2

Prepare the door and check dimensions

A
Measure to confirm that the hole in
the door is either 2-1/8" (54 mm) or
1-1/2" (38 mm).
2-1/8"
54 mm
or
1-1/2"
38 mm
Note: Additional door preparation may be
required for doors with 1-1/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep
3

Install the latch and strike

A
Is the door edge chiseled?
YES
or
chiseled
Use latch "J". If the
latch bolt is not already
extended, extend the
latch bolt as shown.
J
Kit "C"
Gold adapter
Silver mounting
Silver adapter
plate
X2
Black adapter
Gold adapter
B1
C1
X1
Interior assembly
Interior assembly
screws
screws
Mounting
D
plate screws
B2
C2
Interior cover
Interior cover
screws
screws
B3
E
B
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm).
2-3/8" or 2-3/4"
60 or 70 mm
actual
size
P
B
Hold the latch in front of the door hole, with the latch
face flush against the door edge.
NO
not
chiseled
Use latch "K" (not
included). If the latch
bolt is not already
extended, extend the
latch bolt as shown.
K
C
Is the D-shaped hole centered in the door hole?
D-shaped hole
No adjustment is required.
Proceed to next step.
Interior
Latch
Assembly
G
X3
Battery
pack
F
X2
Drive-in
latch
D
H
needed, please contact
Interior
Interior
Kwikset to order a drive-in
cover
assembly
E
Interior conversion kit
Existing
Latch
Existing
New Interior
Exterior
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep
C
Measure to confirm that the hole in
the door edge is 1" (25 mm).
b a
c k
s e
t
Q
J
K
YES
NO
or
D-shaped hole
Rotate latch face as
shown to extend latch.
J
K
1 / 4
1-866-863-6584 • www.kwikset.com
Required Tools
Ruler
Phillips head screwdriver
Strike
Latch screws
03809
L
J
Keys
Strike screws
M
K
46780
SmartKey
"K" is not included. If
tool
latch for your lock.
N
Full smart lock set
New Interior
D
Measure to confirm that the door is
either 1-3/8" or 1-3/4" (35 mm or 44
mm) thick.
1"
25 mm
R
D
Which latch are you installing?
Latch "J"
"UP" is
on top
J
P (x2)
E
Install strike on the door frame.
Make sure the hole in the door frame is drilled a
minimum of 1" (25 mm) deep.
Longer screws
install closest to
the door jamb.
Kwikset Technical Support
Existing key
4 AA batteries
Exterior
Assembly
Adapter
P
Q
ring
T
Cylinder
guard
U
Guard
cover
V
R
S
Cylinder
W
New Latch
New
Exterior
1-3/8" or 1-3/4"
35 or 44 mm
S
Latch "K"
or
K
"UP" is
on top
wood
block
S (x2)
L
R (x2)
door frame

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 914CZigBee C4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kwikset 914CZigBee C4

  • Page 1 Exterior Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep Measure to confirm that the hole in Measure to confirm that the backset is Measure to confirm that the door is Measure to confirm that the hole in the door is either 2-1/8"...
  • Page 2 Install the exterior assembly and mounting plate What is the diameter of the hole in the door? Install cylinder in exterior assembly. Diameter is 2-1/8" Diameter is 1-1/2" (54 mm) (38 mm) 2-1/8" 1-1/2" 54 mm 38 mm Install “T” Do not on exterior install “T”.
  • Page 3 Perform the door handing process This step will teach the lock the orientation of your door and is crucial for lock operation. Make sure the door is open. Insert the battery The Status LED will flash red The latch bolt will retract and extend on its Install 4 AA batteries pack while PRESSING AND HOLDING the and green, and the lock will...
  • Page 4 Reference Guide Kwikset Convert Back Panel at a Glance Switches 1 2 3 4 on off Button “A” Button “B” Back panel 1. Status LED 3. Audio Program button Door lock status LED blinks every 6 Beeping sound is heard during...

Table of Contents