Kwikset 910CNT ZB 11P SMT Installation And User Manual

Kwikset 910CNT ZB 11P SMT Installation And User Manual

Smartcode 910 series electronic deadbolt with home connect with z-wave

Advertisement

Quick Links

63983 / 02
Z-Wave
Signature Series Deadbolt
with Home Connect
Installation and User Guide

Required tools

4 AA Batteries
Ruler
Phillips head screwdriver
Additional Tools (depending on application)
Hammer
Wood block
1
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.
Measure to confirm that the hole in
A
the door is either 2-1/8" (54 mm) or
1-1/2" (38 mm).
2-1/8"
54 mm
or
1-1/2"
38 mm
Note: Additional door preparation may be
required for doors with 1-1/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep.
2
Install the latch and strike
A
Is the door edge chiseled?
YES
or
chiseled
Use latch "A". If the
latch bolt is not already
extended, extend the
latch bolt as shown.
A
Kwikset
1-866-863-6584
www.kwikset.com
Measure to confirm that the backset is
B
either 2-3/8" or 2-3/4" (60 or 70 mm).
b a
2-3/8" or 2-3/4"
60 or 70 mm
B
Hold the latch in front of the door hole, with the latch
face flush against the door edge.
NO
not
chiseled
Use latch "B" (not
included). If the latch
bolt is not already
extended, extend the
latch bolt as shown.
B
C
Are the latch holes centered in the door hole?
No adjustment is required.
Proceed to next step.

Parts in the box

Latch
A
B
"B" is not included. If needed,
please contact Kwikset to order
a drive-in latch for your lock.
Mounting
Plate
C
Strike
Cylinder
D
E
C
Measure to confirm that the hole in
the door edge is 1" (25 mm).
c k
s e
t
A
B
YES
NO
or
Rotate latch face as
shown to extend latch.
A
B
1 / 4
Interior Assembly
Exterior Assembly
Traditional
Contemporary
Traditional
L
M
F
F
Fasteners
G
G
R
H
H
T
Keys
SmartKey
tool
W
J
K
Measure to confirm that the door is
D
between 1-3/8" and 1-3/4"* (35 mm
and 44 mm*) thick.
1"
25 mm
*Service kits for 2-1/4" (57 mm) thick doors
are available through Kwikset.
D
Which latch are you installing?
Latch "A"
or
A
R or S
(2x)
E
Install strike on the door frame.
Make sure the hole in the door frame is drilled a
minimum of 1" (25 mm) deep.
Longer screws
install closest to
the door jamb.
X (2x)
W (2x)
Contemporary
P
N
Q
S
U
V
X
1-3/8" – 1-3/4"*
35 – 44 mm*
Latch "B"
B
wood
block
D
door frame

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 910CNT ZB 11P SMT and is the answer not in the manual?

Questions and answers

Summary of Contents for Kwikset 910CNT ZB 11P SMT

  • Page 1 Wood block Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep. Measure to confirm that the hole in Measure to confirm that the backset is...
  • Page 2 Programming and 12" Troubleshooting Guide on the smart home controller (305 mm) “Deadbolt with Home Connect” page at www.kwikset.com/ wirelesslocks The lock and controller must remain stationary for at least 60 seconds during the pairing process. 2 / 4...
  • Page 3 Install interior assembly Push turnpiece shaft onto torque blade. Secure interior assembly with supplied screws. torque blade U (2x) turnpiece shaft Note: Turnpiece may not rotate smoothly until after step 6. Perform the door handing process This step will teach the lock the orientation of your door and is crucial for lock operation. Make sure the door is open.
  • Page 4: Troubleshooting

    Turnpiece Switches and Status LED colors Troubleshooting Switches Status 1 2 3 4 A complete Programming and Troubleshooting Guide is available on the “Deadbolt with Home Connect” page at kwikset.com/wirelesslocks Switch Function Color Lock Status Blinking green Unlocked Door lock status LED blinks every 6...

This manual is also suitable for:

910cnt zw 11p smt910cnt zw 15 smt910cnt zb 15 smt910cnt zw 26 smt910cnt zb 26 smt910trl zbc4 11p smt ... Show all

Table of Contents