Table of Contents
Advertisement
10. Remove all the filtering pocket tension rods (4, Fig.
AC).
11. Open the upper retaining cord (5, Fig. AC) of the
closed pocket filter to remove it from the upper frame
(6).
12. Remove the internal pocket separator (7, Fig. AC).
13. Clean the polyester fiber surface (8, Fig. AC) from the
dirty side, using an external vacuum cleaner,
spreading it out completely or cleaning pocket by
pocket. At the same time, clean both the surfaces of
the pocket separator (7, Fig. AC) removing anything
deposited on them. Check the filtering surface for
tears. In case of tears, replace it. It is also possible to
use compressed air (max. 6 Bar), blowing the air from
the clean side towards the dirty side.
WARNING!
Do not wash the filter with water. The
polyester fibber can shrink and become
unusable.
14. Reassemble all the filter components in the reverse
order of disassembly.
15. If necessary, clean the filter compartment rubber seal
(3, Fig. AB) along its perimeter and check its integrity.
If necessary, replace it.
16. Reassemble all the components in the reverse order
of disassembly.
SKIRT HEIGHT AND OPERATION CHECK
Side skirts
1.
Drive the machine on a level ground that is suitable
for checking the skirt height.
2.
Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3.
Turn the ignition key (14, Fig. B) to "0" position.
4.
Disengage the retainers (8 and 6, Fig. C) and open
the right and left doors (7 and 5).
5.
Check the side skirt (2, Fig. F) integrity.
Replace the skirts when they have cuts (1, Fig. Q)
larger than 20 mm or cracks/tears (2) larger than 10
mm (for skirt replacement, see the Service Manual).
6.
Check that side skirt (2, Fig. F) height from ground is
within 0 – 3 mm (Fig. R).
After loosening the screws (3, Fig. F), if necessary,
adjust the skirt position.
Then tighten the screws (3).
146 2603 000(1)2005-03 A
USER MANUAL
Front and rear skirt
7.
Remove the main broom, as described in the related
paragraph.
8.
Check the front (1, Fig. W) and rear (2) skirts for
integrity.
Replace the skirts when they have cuts (1, Fig. Q)
larger than 20 mm or cracks/tears (2) larger than 10
mm (for skirt replacement, see the Service Manual).
9.
Check that the front (1, Fig. W) and rear (2) skirts rub
lightly on the floor but are not completely lifted from
the ground (Fig. S).
After loosening the screws (3, Fig. W), adjust the skirt
position if necessary.
Then tighten the screws (3).
10. Press the front (21, Fig. B) skirt lifting pedal
completely, and check that the front skirt lifts 5 cm
approximately. Release the pedal and check that the
skirt returns to the initial position and not in an
intermediate position. If necessary, adjust the skirt
lifting cable (1, Fig. X), by means of the adjuster (2)
on the left front side of the skirt (for the front skirt
control cable replacement, see the Service Manual).
11. Reassemble the removed components in the reverse
order of disassembly.
HOPPER LIFTING SYSTEM HYDRAULIC
OIL LEVEL CHECK
CAUTION!
These operations must be performed with
the hopper (4, Fig. C) in its original position
(as shown in the figure).
1.
Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
2.
Turn the ignition key (14, Fig. B) to "0" position.
3.
Open the hood (1, Fig. V).
4.
Check that the hydraulic oil level in the tank (19, Fig.
V) is between the MIN (minimum level) and MAX
(maximum level) marks shown in figure Y.
5.
If necessary, add hydraulic oil - viscosity grade 32 cSt
- through the plug (1, Fig. Y).
6.
Close the hood (1, Fig. V).
ENGLISH
FLOORTEC R 580 P
15
Advertisement
Table of Contents
