Clarke focus ii rider 28 d base; clarke focus ii rider 34 d obc base; clarke focus ii rider 34 d base; clarke focus ii rider 28 b base; clarke focus ii rider 28 b obc base; clarke focus ii rider 28 d obc base; 56114000; 56114001; 56114002; 56114003; 56114 (93 pages)
Summary of Contents for Nilfisk-ALTO FLOORTEC R 580 P
Page 1
www.nilfisk-alto.com FLOORTEC R 580 P DEUTSCH BETRIEBSANLEITUNG FRANÇAIS MANUEL D’UTILISATION ENGLISH USER MANUAL NEDERLANDS GEBRUIKSAANWIJZING...
Nilfisk-Alto Service Center in case of doubts procedures must be carried out by qualified personnel or regarding the interpretation of the instructions and for any by Nilfisk-Alto Service Centers (listed at the end of this further information. manual). Only original spare parts and accessories must be used.
– Always protect the machine against the sun, rain and – Switch the engine off and leave it to cool down for a few bad weather, both under operation and inactivity minutes before unscrewing the petrol tank cap. condition. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
– Running the engine with an insufficient quantity of petrol can seriously damage the engine. Check the oil level with the engine off and the machine on a level surface. FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
14. Rear drive wheels on fixed axis 15. Front steering wheel 16. Left side skirt 17. Right side skirt 18. Front skirt 19. Rear skirt 20. Dust filter container 21. Petrol engine exhaust pipe 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
Reverse micro-switch SW3: Hopper enabling switch Oil type 15 W 40 SW4: Hopper lifting/lowering switch SW5: Hopper opening/closing switch NOTE SW6: Horizontal hopper micro-switch For other petrol engine data/values, see User's Manual. FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
10. Warm up the engine for a few minutes with the lever Engage the parking brake by pressing the brake in MIN position (idle speed). pedal (22, Fig. B) and by activating the brake lock control lever (15). FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
The hopper can be overturned only if it is automatically stops the engine. not completely turned (horizontal position). The machine is ready to start working again. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
– Raise the hood (13, Fig. C). – Remove the screw (15, Fig. V). – Close the hood (13, Fig. C); – Push the machine. – After pushing the machine, install the screw (15, Fig. V). FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
(4): maintenance operations to be performed by an authorized Briggs & Stratton dealer. (5): if considered necessary by the person in charge of the maintenance. (6): replace hydraulic oil for the first time after 500 hours, then after 2,000 hours or every year. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
When the broom is too worn to be adjusted, replace it as shown in the next paragraph. Engage the retainer (6, Fig. C) and close the left door (5). FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
Perform step 1 again to check the proper adjustment of the side broom height from the ground. When the broom is too worn to be adjusted, replace it as shown in the next paragraph. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
Remove the filter-shaker motor (1, Fig. AC) by filter body for tears. unscrewing the two fixing screws. Open the filter-shaker motor support unit (2, Fig. AC) completely and release the filtering pocket tension rods (3). FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
Check that side skirt (2, Fig. F) height from ground is within 0 – 3 mm (Fig. R). After loosening the screws (3, Fig. F), if necessary, adjust the skirt position. Then tighten the screws (3). 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
MIN (minimum level) and MAX (maximum level) marks (1, Fig. AD). If necessary, top Then insert the dipstick (12, Fig. V) again. 16. Carry out steps from 1 to 6 in the reverse order. FLOORTEC R 580 P 146 2603 000(1)2005-03 A...
Unscrew the fixing screws and remove the engine exhaust system end (31, Fig. V). Clean the spark screen as indicated in the Petrol Engine Manual. Carry out steps from 1 to 5 in the reverse order. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
(maximum speed), and check that the centrifugal pulley engages. With the engine Malfunction of the hood safety micro-switch. compartment (13, Fig. C) Please contact the Nilfisk-Alto Service Center. hood lifted, the petrol engine keeps running. (*): For the related procedure, see the Petrol Engine User Manual.
– Polyester dust filter – Main and side brooms – Engine oil – Hydraulic oil – Plastic components and hoses CAUTION! The removed components must be disposed of properly according to the Law in force. 146 2603 000(1)2005-03 A FLOORTEC R 580 P...
Need help?
Do you have a question about the FLOORTEC R 580 P and is the answer not in the manual?
Questions and answers