Battery Charger Options; Additional Items Required; Hardware & Accessories; Adhesives & Building Supplies - GREAT PLANES Fokker D.VII ARF ElectriFly Instruction Manual

the instructions may differ slightly from the photos. In those
instances the written instructions should be considered
as correct.
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in
first-class condition.
5. You must correctly install all R/C and other components so
that the model operates correctly on the ground and in the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you're not a member of a club, your local hobby
shop has information about clubs in your area whose
membership includes experienced pilots.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and flyability of your finished model depends on
how you build it; therefore, we cannot in any way
guarantee the performance of your completed model, and
no representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.

BATTERY CHARGER OPTIONS

The Great Planes Fokker D.VII EP ARF is designed for use
with LiPo (Lithium-Polymer) batteries only. All LiPo batteries
require a charger specifically designed for charging LiPo
batteries. The use of a charger not designed for charging
LiPo batteries will result in damage to the batteries and
possibly a fire.
We recommend the use of the Great Planes Triton
Peak Charger (GPMM3150), the ElectriFly DC PolyCharge
(GPMM3010) or for charging more than one battery at a
time the ElectriFly PolyCharge4 (GPMM3015).

ADDITIONAL ITEMS REQUIRED

Hardware & Accessories
In addition to the items listed in the "BATTERY CHARGER
OPTIONS" section, the following is the list of hardware and
accessories required to finish the Fokker D.VII EP ARF.
Order numbers are provided in parentheses.
❏
4-Channel radio with four micro servos with a minimum
17 oz/in each such as the Futaba
❏
(1) ElectriFly SS-25 25 amp brushless ESC (GPMM1820)
❏
(1) ElectriFly 3.5mm Bullet
(female) connector adapter (GPMM3122)
❏
(1) ElectriFly 1250mAh LiPo 3-cell battery (GPMP0823)
❏
(1) Futaba R114F 4-channel FM receiver
(FUTL0443, FUTL0442)
❏
(1) Futaba "Y-harness" (FUTM4130)
❏
(1) ElectriFly RimFire C28-30-950 brushless
motor (GPMG4560)
❏
(1) 10x4.5 Prop (GPMQ6660)
❏
(1) 3mm Prop adapter (GPMQ4959)
❏
(1) 6" [152mm] Servo extension
Accessories & Building Supplies
In addition to common household tools and hobby tools, this
is the "short list" of the most important items required to build
the Fokker D.VII EP ARF. Great Planes Pro
glue are recommended.
❏
1 oz. [28g] Thin Pro CA (GPMR6002)
❏
1 oz. [28g] Medium Pro CA (GPMR6008)
❏
Hook & Loop material (GPMQ4480)
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack, HCAR0211)
❏
Medium T-pins (100, HCAR5150)
❏
Builder's Triangle Set (HCAR0480)
❏
K & S #801 Kevlar
❏
Pliers
❏
Wire cutter
❏
Clear tape
Optional Supplies & Tools
™ DC
™
Here is a list of optional tools mentioned in the manual that
will help you build the Fokker D.VII EP ARF.
❏
Stick-on segmented lead weights (GPMQ4485)
❏
Top Flite ® MonoKote
❏
Top Flite Hot Sock
❏
Top Flite MonoKote heat gun (TOPR2000)
❏
2 oz. [57g] Spray CA activator (GPMR6035)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
3
S3107 (FUTM0025)
®
™ (male) to 2mm Bullet
™ CA and Epoxy
® thread or string (for stab alignment)
® sealing iron (TOPR2100)
™ iron cover (TOPR2175)