MVC-FD91 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 1998.10 E Model Australian Model Hong Kong Model Tourist Model Chinese Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM...
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
TABLE OF CONTENTS SERVICE NOTE • VP-49 (Steady Shot Control) ····································································· 5 Schematic Diagram ........4-12 • VP-49 (Steady Shot Control, Active Prism Actuator GENERAL Drive) Printed Wiring Board ........4-15 Before using your camera ............1-1 • FC-67 (Camera Y/C Process, DRAM Control, Parts identification ..............
1-3. Camera System Adjustments ......... 5-10 Picture Frame Setting ............ 5-10 HALL Adjustment ............5-11 Flange Back Adjustment ..........5-11 Flange Back Check ............5-12 Light Level Adjustment ..........5-12 Auto White Balance Standard Data Input ..... 5-13 Auto White Balance Adjustment ........5-13 Color Reproduction Adjustment ........
The electric shock is caused by the charged voltage which is kept without discharging when the main power of the MVC-FD91 is simply turned off. Therefore, the remaining voltage must be discharged as described below.
[How to connect the extension cable] 1. Connection between the FDD unit and PK-45 board. 1) Connection of the extension cable (J-6082-427-A) 3) Connection between the FDD unit and extension cable Conductor side CN013 Conductor side FDD unit Conductor side Extension cable Extension cable (J-6082-427-A)
[Description on Self-diagnosis Display] Self-diagnosis display • C: ππ: ππ The contents which can be handled by customer, are displayed. • E: ππ: ππ Note : The “Self-diagnosis” data is backed up by the coin lithium The contents which can be handled battery.The data will be lost and initialized when the coin lithium by engineer, are displayed.
MVC-FD91 SECTION 1 This section is extracted from GENERAL instruction manual.
1-10...
1-11E...
MVC-FD91 SECTION 2 DISASSEMBLY NOTE: Follow the disassembly procedure as shown in the flow chart below. LCD check LCD unit, 2-5. Service position PD-104 board EVF check EVF block (1), 2-1. 2-2. EVF block (2) Service position RL-52 board 2-3.
2-2. EVF BLOCK (2) 1 Remove the claws 3 Cover the cushion and diffusion plate with a piece of paper and adhesive tape or the like so that the parts must not be scattered. [EVF CHECK SERVICE POSITION] 2 VF-131 board (1) VF-131 board 7 Lens holder assembly...
2-4. CABINET (ST) ASSEMBLY, FLASH UNIT, MA-348 BOARD 6 Two tapping screws (B2 × 5) 4 Cabinet (upper) (POP) 2 MA-348 board assembly !º Remove the claws (Note) !¡ Cabinet (upper) (POP) !™ Cabinet (lower) (POP) assembly !£ FLASH unit 9 Tapping screw (B2 ×...
2-6. LENS BLOCK 5 Screw (M2 × 3) 8 Cabinet (LT) !ª SW block (side sw) flexible board (10P) Be careful that the 6 Screw (M2 × 4), board is very short. lock ace, P2 @§ Flexible board (from lens block) 7 Remove the claw !•...
2-7. CD-207 BOARD, VP-49 BOARD, SE-78 BOARD !∞ LENS flame (upper) !¡ Tapping screw (B2 × 5) !™ Screw (M2 × 3) 1 Tite (2), +B Tapping (P) 9 Tapping screw (B2 × 5) !º Screw !¢ Remove the claws (M2 ×...
2-8. FC-67 BOARD, DD-119 BOARD 6 Remove the claws 7 FC-67 board Slide it in the direction of the arrow a , then remove it. 5 Screws (M2 × 3) 3 DD-119 (110) board 1 Screws (M2 × 3) 2 Board to board connector (50P) 4 FP-65 flexible board (70P) [MAIN (FC-67) BOARD CHECK SERVICE POSITION] Cabinet (front) assembly...
2-9. PK-45 BOARD, FDD BLOCK ASSEMBLY !º Two tapping screws (B2 × 5) !¡ LCD block assembly 7 FP-69 flexible board (28P) 3 FDD flexible board (side 1) (5P) 2 FDD flexible board (side 0) (5P) S691 1 FDD flexible board (18P) (PANEL REV) When re-assembling set this knob the center...
2-10.CIRCUIT BOARDS LOCATION PD-104 VF-131 (BACK LIGHT DRIVE) FC-67 LCD DRIVE, CAMERA Y/C PROCESS, TIMING GENERATOR, DRAM CONTROL, LENS BACK LIGHT DRIVE MOTOR DRIVE, D/A FLASH UNIT CONVERTER, AUDIO A/D.D/A CONVERTER, MA-348 FD/SYSTEM CONTROL, (MIC AMP, ALC) HI CONTROL CD-207 (CCD IMAGER) SE-78 YAW,...
MVC-FD91 MVC-FD91 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM...
MVC-FD91 3-2. CAMERA/FDD INTERFACE BLOCK DIAGRAM IC401 2,4 IC401 8 IC101 @§ CAMERA REC IC101 2 – !¡ IC103 #§,$∞ CAMERA REC/PB CAMERA REC/PB 7.5Vp-p 78µsec 1.8Vp-p 1.4Vp-p 3.1Vp-p 3.8Vp-p 78µsec 78µsec 60nsec 60nsec IC102 $º,$¡ IC102 4 CAMERA REC/PB CAMERA REC IC801 *£...
MVC-FD91 3-3. MODE CONTROL BLOCK DIAGRAM IC702 $º 20MHz 3.8Vp-p IC702 %£ 3.4Vp-p 32.768kHz IC237 @¢ 12MHz 2.8Vp-p 3-10 3-11...
MVC-FD91 MVC-FD91 3-4. LCD BLOCK DIAGRAM IC802 @º IC802 @™ IC802 @¢ 4Vp-p 4Vp-p 4Vp-p 156µsec 156µsec 156µsec IC901 1 CAMERA REC/PB 5Vp-p 2µsec IC802 8 0.3Vp-p 78µsec IC802 9 IC802 @•,@ª 0.45Vp-p 78µsec 3.2Vp-p IC802 !º 1.5msec IC843 7 0.25Vp-p...
MVC-FD91 MVC-FD91 3-5. COLOR EVF BLOCK DIAGRAM IC5001 9 IC5001 @º IC5001 @™ IC5001 @¢ 0.35Vp-p 7.6Vp-p 7.6Vp-p 7.6Vp-p IC5001 8 0.35Vp-p IC5001 !º 0.2Vp-p IC5102 #∞ 3.2Vp-p IC5101 !∞ IC5102 $∞ IC5102 @¶ 14.0Vp-p 78µsec 3.2Vp-p 3.2Vp-p IC5102 $¡...
MVC-FD91 3-6. POWER BLOCK DIAGRAM IC301 $§ 2.0Vp-p 2.1µsec IC301 $¢ 0.8Vp-p 2.2µsec 3-18 3-19 3-20E...
MVC-FD91 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM FRAME SCHEMATIC DIAGRAM...
MVC-FD91 MVC-FD91 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-207 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-207 Board; 2,000 Series — CD-207 THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS BOARD (In addition to this, the necessary note is printed in each block)
MVC-FD91 SE-78 (YAW, PITCH SENSOR) PRINTED WIRING BOARD — Ref. No. SE-78 Board; 1,000 Series — SE-78 BOARD C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 CN201 A-5 IC201 L201 R201 R202...
MVC-FD91 VP-49 BOARD IC237 @¢ 2.8Vp-p 12MHz STEADY SHOT CONTROL 4-12 4-13 4-14 VP-49...
MVC-FD91 VP-49 (STEADY SHOT CONTROL, ACTIVE PRISM ACTUATOR DRIVE) PRINTED WIRING BOARD — Ref. No. VP-49 Board; 2,000 Series — VP-49 BOARD C231 IC234 R253 C232 IC235 R254 C234 IC236 R255 C235 IC237 R256 C236 IC239 R257 C237 IC240 R258...
MVC-FD91 FC-67 (CAMERA Y/C PROCESS, DRAM CONTROL, LENS MOTOR DRIVE, D/A CONVERTER, AUDIO A/D.D/A CONVERTER, FD/SYSTEM CONTROL, HI CONTROL) PRINTED WIRING BOARD — Ref. No. FC-67 Board; 10,000 Series — FC-67 BOARD (SIDE A) C001 C865 R012 R740 C002 C866...
MVC-FD91 MVC-FD91 FC-67 BOARD (SIDE B) C012 G-13 C607 A-10 L451 D-11 R423 G-11 C013 G-13 C608 A-10 L452 A-11 R424 G-11 C014 G-13 C609 A-10 L601 R425 G-11 C015 G-13 C610 L602 A-10 R426 G-11 C016 G-13 C611 L603...
MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. FC-67 BOARD (1/7) IC101 2 – !¡ IC102 !™,!£ CAMERA REC/PB CAMERA REC 3Vp-p 3.1Vp-p 60nsec 60nsec !º IC101 !§ IC103 #§,$∞ CAMERA REC/PB CAMERA REC/PB 3.8Vp-p 4.0Vp-p...
MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. DRAM CONTROL 4-25 4-26 4-27 FC-67 (2/7)
MVC-FD91 MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. LENS MOTOR DRIVE 4-29 4-30 FC-67 (3/7)
MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. FC-67 BOARD (4/7) CAMERA REC/PB !¡ !ª IC601 5 Q602 E 3.8Vp-p 0.16Vp-p 60nsec 78µsec !™ @º IC601 !¢ Q603 E 0.1Vp-p 0.1Vp-p 78µsec 78µsec !£ IC601 !ª...
MVC-FD91 MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. AUDIO A/D.D/A CONVERTER 4-35 4-36 FC-67 (5/7)
MVC-FD91 MVC-FD91 For schematic diagram • Refer to page 4-17 for printed wiring board. FC-67 BOARD (6/7) CAMERA REC/PB @¡ IC801 *£ 16.26MHz 5.0Vp-p @™ IC851 *º 2.0Vp-p 7.41MHz FD/SYSTEM CONTROL 4-37 4-38 4-39 4-40 FC-67 (6/7)
MVC-FD91 For schematic diagram RL-52 (RELEASE SWITCH) PRINTED WIRING BOARD • Refer to page 4-17 for printed wiring board. — Ref. No. RL-52 Board; 2,000 Series — RL-52 BOARD FC-67 BOARD (7/7) CN103 A-2 CAMERA REC/PB @£ D103 IC702 $º...
MVC-FD91 For schematic diagram • Refer to page 4-57 for printed wiring board. PK-45 BOARD (1/4) IC601 $™ CAMERA REC/PB 3.2Vp-p 4.0MHz REC/PB AMP, MOTOR DRIVE 4-45 4-46 4-47 PK-45 (1/4)
MVC-FD91 MVC-FD91 For schematic diagram • Refer to page 4-57 for printed wiring board. PK-45 BOARD (2/4) CAMERA REC/PB IC802 8 0.3Vp-p 78µsec IC802 9 0.45Vp-p 78µsec IC802 !º 0.25Vp-p 78µsec IC802 @º 4Vp-p 156µsec IC802 @™ 4Vp-p 156µsec IC802 @¢...
MVC-FD91 For schematic diagram • Refer to page 4-57 for printed wiring board. PK-45 BOARD (3/4) CAMERA REC/PB IC841 1 3.3Vp-p 78µsec !º IC841 4 3.3Vp-p 20msec !¡ IC842 @§ 4.5Vp-p 150nsec !™ IC842 #¶ 3.3Vp-p 78µsec !£ IC843 7 4.5Vp-p...
MVC-FD91 MVC-FD91 For schematic diagram • Refer to page 4-57 for printed wiring board. MODE SWITCH 4-55 4-56 PK-45 (4/4)
MVC-FD91 PK-45 (REC/PB AMP, MOTOR DRIVE, LCD DRIVE, TIMING GENERATOR, MODE SWITCH) PRINTED WIRING BOARD — Ref. No. PK-45 Board; 2,000 Series — PK-45 BOARD BH701 D-9 D707 R624 D-11 R848 E-16 D709 E-13 R625 R849 E-16 C601 E-12 D710...
MVC-FD91 MVC-FD91 PD-104 (BACK LIGHT DRIVE) PRINTED WIRING BOARD — Ref. No. PD-104 Board; 2,000 Series — PD-104 BOARD C901 Q901 R937 C901 Q902 R938 C902 Q903 R939 C903 Q904 R940 C904 Q905 R941 C905 Q906 R942 C906 Q907 R943...
MVC-FD91 MVC-FD91 MA-348 (MIC AMP, ALC) PRINTED WIRING BOARD — Ref. No. MA-348 Board; 1,000 Series — MA-348 BOARD C101 C102 C103 C104 C105 C106 C107 C108 C109 C111 C112 C113 C114 C115 CN101 A-1 CN102 B-1 D101 D102 IC101...
MVC-FD91 MVC-FD91 VF-131 (LCD DRIVE, TIMING GENERATOR) PRINTED WIRING BOARD — Ref. No. VF-131 Board; 10,000 Series — VF-131 BOARD C5001 CN5001 F-4 R5041 G-3 C5002 CN5202 G-11 R5044 G-3 C5003 R5046 G-9 C5004 D5101 D-8 R5048 G-4 C5005 D5102 F-4...
MVC-FD91 VF-131 VF-131 BOARD BOARD (1/2) (2/2) CAMERA REC/PB CAMERA REC/PB IC5101 !∞ IC5001 8 0.35Vp-p 14.0Vp-p 78µsec IC5001 9 IC5102 @¶ 3.2Vp-p 0.35Vp-p IC5001 !º IC5102 #∞ 0.2Vp-p 3.2Vp-p !º IC5001 @º IC5102 $¡ 7.6Vp-p 2.5Vp-p 16.4MHz !¡ IC5001 @™...
MVC-FD91 DD-119 BOARD CAMERA REC/PB IC301 $¢ 0.8Vp-p 2.2µsec IC301 $§ 2.0Vp-p 2.1µsec DC/DC CONVERTER 4-75 4-76 4-77 4-78 DD-119...
MVC-FD91 DD-119 (DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-119 Board; 2,000 Series — DD-119 BOARD C302 C357 Q308 R332 C303 C358 Q309 R333 C304 C359 Q310 R334 C305 C360 Q311 R335 C306 C361 Q312 R336 C307 C363 Q313...
MVC-FD91 MVC-FD91 MF/ZM/SW BLOCK 4-82E...
MVC-FD91 SECTION 5 ADJUSTMENTS 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Regulated power supply • Digital voltmeter • Frequency counter • AC power adapter Ref. No. Name Parts Code...
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-5. 2) Connect the Adjustment remote commander to PK-45 board CN701 via CPC-12 jig (J-6082-436-A).
Adjustment CPC-12 remote commander (J-6082-436-A) LANC jack Oscilloscope EXT.TRIG. FDD UNIT Must be connected when the electronic viewfineder is used. Must be connected when the FLASH UNIT is used. CN701 PK-45 CN601 CN012 CN013 board CN941 CN603 CN602 CN011 Extension cable (J-6082-427-A) Must be connected Note 1: When connecting the extension cable,...
1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. PLAY/STILL/MOVIE switch (PK-45 board S708, 709) ..........STILL FOCUS switch (FRONT SW block) ..... MANUAL STEADY SHOT switch (FRONT SW block) ....OFF PROGRAM AE switch (SIDE SW block) ........
1-2. INITIALIZATION OF F, E PAGE DATA Address Remark Initial value 1. Initializing the F, E Page Data Fixed data-1 Note: If the F, E page data is initialized, all adjustments must be performed (Initialized data) again. Adjusting page Fixed data-2 Adjusting Address 00 to FF Adjusting page...
Address Address Remark Remark Initial value Initial value Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 White balance adj.
Address Remark Address Remark Initial value Initial value Flange back adj. Fixed data-1 Fixed data-1 (Initialized data) HALL adj. Table. 5-1-1. Fixed data-1 4. E Page table Light level adj. Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the F, E Page Data”.) AWB standard data input Fixed data-2 : Modified data.
Address Remark Address Remark Initial value Initial value Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Strobe white balance adj. Fixed data-1 (Initialized data) Fixed data-2 Fixed data-2 Fixed data-1...
Address Address Remark Remark Initial value Initial value Fixed data-1 CCD defect compensation (Initialized data) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Steady shot adj. Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 (Initialized data) Fixed data-1...
1-3. CAMERA SYSTEM ADJUSTMENTS 1. Picture Frame Setting Check on the oscilloscope Subject Color bar chart standard picture frame 1. Horizontal period (1.5m from the front of the protection glass) Pin 9 of CN701 (VG) of PK-45 board Measurement Point External trigger (Horizontal period) : Pin 8 of CN701 (COM) of PK-45 board External trigger (Vertical period) :...
2. HALL Adjustment 3. Flange Back Adjustment For detecting the position of the lens iris, adjust the hall AMP gain The inner focus lens flange back adjustment is carried out and offset. automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing.
4. Flange Back Check 5. Light Level Adjustment Adjust the standard LV value. Subject Siemens star (2.0 m from the front of the protection Subject Clear chart glass) (Color bar standard picture frame) (Luminance : approx. 200 lux) Adjustment Page Measurement Point Check operation on LCD screen Adjustment Address...
6. Auto White Balance Standard Data Input 7. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.
8. Color Reproduction Adjustment Adjust the color separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart standard picture frame CHX: Pin 1 of CN701 of PK-45 Measurement Point board (PANEL B-Y) CHY: Pin 3 of CN701 of PK-45 board (PANEL R-Y) Measuring Instrument Oscilloscope (X-Y mode)
9. White Balance Check 10. Strobe Light Level Adjustment Adjust the minimum gain when the strobe light flashes. Subject Clear chart (Color bar standard picture frame) Subject Clear chart (Color bar standard picture frame) Filter ND filter 1.0 and 0.3 Measurement Point Display data of page : 1 Measurement Point...
11. Strobe White Balance Adjustment 12. Strobe Light Level and White Balance Check Adjust the white balance when the strobe light flashes. Check the light level regulation and the white balance when the strobe light flashes. Subject A plate which reflection rate is 18% (1.0m from the front of the protection Subject A plate which reflection rate is 18%...
13. Steady shot adjustment Adjusting method: • Perform the steady shot adjustment only when replacing the Expose pattern A with the zoom TELE end. angular velocity sensor. When the microprocessor, circuit, etc. Adjust the inclination of the camera so that the vertical black malfunctions, do not perform this adjustment but check operations line comes to the center of the screen.
13-2. Steady Shot Adjustment (2) Subject Pattern B (1.5m from the front of the protection glass) Pin 2 of CN701 of PK-45 board Measurement Point (PANEL Y) External trigger: Pin !¡ of CN701 of PK-45 board (LANC IN) Measuring Instrument Oscilloscope (V period) Adjustment Page Adjustment Address...
14. CCD Defect Compensation 15. CCD Defect Compensation Check Subject Clear chart Subject Clear chart (40 cm from the front of the protection (40 cm from the front of the protection glass) glass) Adjustment Page Measurement Point Display data of page : 3, address : FF Adjustment Address C2 to D5 Measuring Instrument...
1-4. COLOR ELECTRONIC VIEWFINDER [Alignment disk] Use the alignment disks (two disks as pair) shown in below. SYSTEM ADJUSTMENT Disk-1: TFD2-1(+) (Parts code; 8-967-990-01) Note 1: The back light (fluorescent tube) is driven by a high voltage AC Disk-2: TFD2-2(–) (Parts code; 8-967-990-11) power supply.
1. EVF Initial Data Input 2. VCO Adjustment (VF-131 board) Set the VCO free-run frequency. If deviated, the LCD screen will Mode Playback be blurred. Signal Arbitrary Mode Playback Adjustment Page Signal Arbitrary Adjustment Address 6B, 6C, 6F, 70, 74, 75, E0 Pin @™...
3. Bright Adjustment (VF-131 board) 4. Contrast Adjustment (VF-131 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
5. Backlight Consumption Current Adjustment 6. White Balance Adjustment (VF-131 board) (VF-131 board) Correct the white balance. Set the backlight luminance and color temperature. If deviated, the EVF screen color cannot be reproduced. If deviated, the image may become dark or bright. Mode Playback Mode...
1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input Note 1: The back light (fluorescent tube) is driven by a high voltage AC Mode Playback power supply. Therefore, do not touch the back light holder to Signal Arbitrary avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages Adjustment Page caused by static electricity.
2. VCO Adjustment (PK-45 board) 3. D range Adjustment (PK-45 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the LCD driver to the specified value. If deviated, be blurred. the LCD screen will become blackish or saturated (whitish). Mode Playback Mode...
4. Bright Adjustment (PK-45 board) 5. Contrast Adjustment (PK-45 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
6. Color Adjustment (PK-45 board) 7. V-COM Level Adjustment (PK-45 board) Set the color saturation to the standard value. If deviated, the color Set the common electrode drive signal level of LCD to the specified will be to dark or light. value.
8. V-COM Adjustment (PK-45 board) 9. White Balance Adjustment (PK-45 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode Playback...
1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Battery End Adjustment (FC-67 board) Adjusting method: Set the battery end voltage. Adjust the output voltage of the regulated power supply so that If the voltage is incorrect, the life of the battery will shorten. the digital voltmeter display is 6.1 ±...
2. Alignment check (FDD UNIT) Confirm that the FDD alignment is within the specifications. If deviated, reading and writing data from and to the floppy disk become impossible. Or compatibility of the floppy disk with other machines can be lost. Mode Playback Signal...
5-2. SERVICE MODE 2-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
2-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
2-3. SERVICE MODE 1. Setting the Test Mode 3. Switch check (1) Page F Address 10 Page 3 Address 23 Data Function Function When bit value=1 When bit value=0 Normal POWER SW (PK-45 board S702) Forced camera power ON Forced Player power ON XCAM/PB SW (PK-45 board S708) •...
4. Switch check (2) Page 3 Address 13 to 17 Using method: 1) Select page:3, address: 13 to 17. 2) By discriminating the display data, the pressed key can be discriminated. Data Address About“00” About“29” About“54” About“82” About“A6” About“E5” About“FF” VOLUME + VOLUME –...
MVC-FD91 SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark ! or have some differences from the original one.
6-1-2. EVF SECTION supplied LCD902 supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-713-791-81 SCREW (M1.7) * 58 3-960-302-11 CUSHION (1), LCD X-3949-130-1 CABINET (ST) ASSY A-7073-754-A VF-131 BOARD, COMPLETE 3-968-729-51 SCREW (M2), LOCK ACE, P2 1-671-875-11 FP-68 (VF-FC) FLEXIBLE BOARD 3-718-233-01 NUT, PLATE A-7073-752-A MA-348 BOARD, COMPLETE...
6-1-3. CABINET (FRONT) SECTION 112 113 supplied supplied supplied not supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-968-729-01 SCREW (M2), LOCK ACE, P2 1-671-880-11 FP-73 (VP-FC) FLEXIBLE BOARD 3-968-729-11 SCREW (M2), LOCK ACE, P2 1-671-874-11 FP-67 (FC-CD) FLEXIBLE BOARD X-3949-125-1 CABINET (FRONT) ASSY 3-052-985-01 CABINET (LT)
6-1-4. CABINET (REAR) SECTION supplied (including S691) 168 167 S691 supplied supplied SP901 supplied (Note) supplied supplied (Note) The FD block assembly is a mechanical unit which has completely been adjusted in the factory. Ref. No. Part No. Description Remarks Ref.
6-1-5. LCD PANEL SECTION LCD901 ND901 LCD901 not supplied S691 (including S691) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-671-876-21 FP-69 (PD-PK) FLEXIBLE BOARD 1-671-877-21 FP-70 (PANEL) FLEXIBLE BOARD (Including S691) 4-969-980-11 SCREW (M1.4) (IB LOCK), PAN 3-713-791-01 SCREW (M1.7X4), TAPPING, P2 X-3949-132-1 CABINET (FRONT) ASSY, P 3-052-986-01 COVER (FRONT), HINGE...
6-1-6. LENS BLOCK SECTION IC401 not supplied VCL-5214WA (Note) Screw tapping (B tight) 1.7 × 4.5 (Note) Never remove the motors from the lens block because adjustments become necessary to re-assemble them once they are removed. Be sure to read “Note on the CCD imager replacement” on page 4-8 when changing the CCD Imager.
CD-207 DD-119 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor The components identified by mark ! or...
DD-119 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C361 1-135-216-11 TANTALUM CHIP 10uF Q316 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO C363 1-104-913-11 TANTAL. CHIP 10uF Q317 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO C364 1-107-682-11 CERAMIC CHIP Q318 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO C365 1-164-346-11 CERAMIC CHIP Q319 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO...
DD-119 FC-67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R357 1-216-841-11 METAL CHIP 1/16W C019 1-104-851-11 TANTAL. CHIP 10uF R358 1-216-837-11 METAL CHIP 1/16W C020 1-162-970-11 CERAMIC CHIP 0.01uF R360 1-218-883-11 RES,CHIP 0.50% 1/16W C021 1-162-970-11 CERAMIC CHIP 0.01uF R361...
FC-67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C408 1-164-677-11 CERAMIC CHIP 0.033uF C718 1-107-826-11 CERAMIC CHIP 0.1uF C409 1-162-970-11 CERAMIC CHIP 0.01uF C720 1-115-156-11 CERAMIC CHIP C410 1-107-826-11 CERAMIC CHIP 0.1uF C722 1-162-970-11 CERAMIC CHIP 0.01uF C411 1-162-970-11 CERAMIC CHIP...
FC-67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D703 8-719-049-09 DIODE 1SS367-T3SONY IC452 8-759-543-83 IC KM416V1204CT-L6T IC453 8-752-395-40 IC CXD3138R < FERRITE BEAD > IC481 8-759-564-51 IC KZ4E063G21WFP IC601 8-752-384-33 IC CXD3121R-T4 FB101 1-500-284-21 INDUCTOR CHIP 0UH IC701 8-759-298-10 IC S-8423NFS-T2 FB102...
FC-67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q701 8-729-024-48 TRANSISTOR 2SK1830-TE85L R132 1-216-864-11 METAL CHIP 1/16W Q702 8-729-032-62 TRANSISTOR 2SJ347-TE85L R133 1-216-864-11 METAL CHIP 1/16W Q703 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R134 1-216-864-11 METAL CHIP 1/16W Q704 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R135...
FC-67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R612 1-216-834-11 METAL CHIP 1/16W R748 1-216-839-11 METAL CHIP 1/16W R614 1-216-821-11 METAL CHIP 1/16W R749 1-216-853-11 METAL CHIP 470K 1/16W R615 1-216-821-11 METAL CHIP 1/16W R751 1-216-845-11 METAL CHIP 100K 1/16W...
R876 1-216-841-11 METAL CHIP 1/16W < DIODE > R877 1-216-841-11 METAL CHIP 1/16W R878 1-216-841-11 METAL CHIP 1/16W D101 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R879 1-216-841-11 METAL CHIP 1/16W R880 1-216-841-11 METAL CHIP 1/16W < IC > R881 1-216-841-11 METAL CHIP 1/16W...
PD-104 PK-45 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C933 1-107-689-21 TANTAL. CHIP R918 1-216-055-00 METAL CHIP 1.8K 1/10W C934 1-107-826-11 CERAMIC CHIP 0.1uF R919 1-216-845-11 METAL CHIP 100K 1/16W C935 1-107-682-11 CERAMIC CHIP R920 1-216-831-11 METAL CHIP 6.8K 1/16W...
R631 1-216-857-11 METAL CHIP 1/16W < DIODE > R632 1-216-833-11 METAL CHIP 1/16W R635 1-216-864-11 METAL CHIP 1/16W D701 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R701 1-216-824-11 METAL CHIP 1.8K 1/16W D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) D715 8-719-064-05 DIODE TLGU1002(TPX1,SONY) R702 1-216-819-11 METAL CHIP...
PK-45 RL-52 SE-78 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R818 1-216-833-11 METAL CHIP 1/16W A-7073-748-A RL-52 BOARD, COMPLETE R819 1-216-845-11 METAL CHIP 100K 1/16W ********************* R820 1-216-805-11 METAL CHIP 1/16W (Ref.No.:2,000 Series) R821 1-216-805-11 METAL CHIP 1/16W R822 1-216-805-11 METAL CHIP...
SE-78 VF-131 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < SENSOR > < CONNECTOR > SE201 1-803-042-31 SENSOR, ANGULAR VELOCITY (PITCH) CN5001 1-784-420-11 CONNECTOR, FFC/FPC (ZIF) 21P SE202 1-803-042-41 SENSOR, ANGULAR VELOCITY (YAW) CN5202 1-750-340-21 CONNECTOR, FFC/EPC (ZIF) 16P ************************************************************ <...
VF-131 VP-49 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5105 1-208-927-11 RES,CHIP 0.50% 1/16W < CONNECTOR > R5106 1-218-975-11 RES,CHIP 1/16W R5107 1-218-970-11 RES,CHIP 1/16W CN231 1-766-343-21 CONNECTOR, FFC/FPC 13P R5108 1-218-982-11 RES,CHIP 270K 1/16W CN232 1-766-337-21 CONNECTOR, FFC/FPC 7P R5109...
VP-49 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R254 1-218-895-11 RES,CHIP 100K 0.50% 1/16W 1-671-877-21 FP-70 (PANEL) FLEXIBLE BOARD R256 1-218-895-11 RES,CHIP 100K 0.50% 1/16W 1-671-878-11 FP-71 (CS-VP) FLEXIBLE BOARD R257 1-216-837-11 METAL CHIP 1/16W 1-671-880-11 FP-73 (VP-FC) FLEXIBLE BOARD R258 1-216-837-11 METAL CHIP...
Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. MVC-FD91 〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to FC-67 board of a set.
MVC-FD91 Sony Corporation 98J1670-1 Printed in Japan ©1998.10 Personal A&V Products Company 9-974-119-11 Published by Quality Engineering Dept. — 186 — (Osaki East)
Comments to this Manuals
Latest comments: