Outback Meteor Select 3 Burner Gas BBQ MH3330 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Outback Manuals
  4. Grill
  5. Meteor Select 3 Burner Gas BBQ MH3330
  6. Assembly and operating instructions manual

Outback Meteor Select 3 Burner Gas BBQ MH3330 Assembly And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Assembly and Operating Instructions for Outback®
Meteor Select 3 Burner Gas BBQ
Drawings are not to scale.
Specifications subject to change
without prior notice.
•
For outdoor use only. Not for commercial use.
•
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
•
Warning: accessible parts may be very hot. Keep young children and pets away.
•
Do not move the appliance during use.
•
Turn off the gas supply at the gas bottle after use.
•
Any modification of the appliance, misuse, or failure to follow the instructions may
be dangerous and will invalidate your warranty. This does not affect your statutory
WARNING
rights.
•
Retain these instructions for future reference.
•
Leak test annually, and whenever the gas bottle is removed or replaced. Check that
the hose connections are tight and leak test each time you reconnect the gas bottle.
•
For Flare-up control please refer to the 'OPERATION' section of this manual.
FOR YOUR SAFETY
If you smell gas:
1.
Shut off gas to the appliance.
2.
Extinguish any open flame.
3.
Open barbecue lid or hood.
4.
If odour continues, discontinue use and
contact your local dealer.
MH3330
FOR YOUR SAFETY
1.
Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2.
A gas bottle not connected for use must not be
stored in the vicinity of this or any other
appliance.
0359

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Meteor Select 3 Burner Gas BBQ MH3330 and is the answer not in the manual?

Questions and answers

Related Manuals for Outback Meteor Select 3 Burner Gas BBQ MH3330

Summary of Contents for Outback Meteor Select 3 Burner Gas BBQ MH3330

  • Page 1 Assembly and Operating Instructions for Outback® Meteor Select 3 Burner Gas BBQ Drawings are not to scale. MH3330 Specifications subject to change 0359 without prior notice. • For outdoor use only. Not for commercial use. • Read instructions before using the appliance. Failure to follow instructions could result in death, serious bodily injury, and/or property loss.

  • Page 2: Parts List

    Parts List Quantity varies according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see the corresponding ‘Hardware Reference Diagram’. Outback® Meteor Select 3 CODE PART Burner Gas BBQ Hood (Pre-Assembled to Body)

  • Page 3: Parts Diagram

    Parts Diagram Quantity varies according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see the corresponding ‘Hardware Reference Diagram’.
  • Page 4 Hardware Reference Diagram Specifications subject to change without prior notice.
  • Page 5 Assembly IMPORTANT! • TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver, adjustable spanner or metric spanner set. • Remove any internal component or packaging from the barbecue body. • Whilst every care is taken in the manufacture of this product, care must be taken during assembly in case sharp edges are present.
  • Page 6 Unscrew the Locknuts (D9) from both ends of the Axle (C11). Slide the axle through the corresponding holes in the left legs. Slide the Wheels (C9) over each end of the axle. Secure the wheels into place with the locknuts. Place the Wheel Hubcaps (C10) onto the outside of the wheels.
  • Page 7 Attach the Left Side Shelf Panel (C2) onto one Side Shelf (C1) using M6x15 Bolts (D5x2pcs) and M6 Nuts (D8x2pcs). Attach the left side shelf assembly to the barbecue body using a ST4.0x10 Screw (D1) and M6x15 Bolts (D5x4pcs) as shown.
  • Page 8 Attach the Right Side Shelf Panel (C3) onto the other Side Shelf (C1) using M6x15 Bolts (D5x2pcs) and M6 Nuts (D8x2pcs). Attach the right side shelf assembly to the barbecue body using a ST4.0x10 Screw (D1) and M6x15 Bolts (D5x4pcs) as shown.
  • Page 9 Attach the Drip Tray Right Bracket (B10) to the barbecue body using M5x15 Bolts (D2x2pcs), Ø5 Washers (D3x2pcs) and M5 Nuts (D4x2pcs) as shown. Repeat the above process for the Drip Tray Left Bracket (B9). NOTE: Ensure that the big tabs of the brackets which stop the drip tray are located at the front of the barbecue.

  • Page 10: Warming Rack

    Carefully lay the Lava Rock (B6) into the barbecue body ensuring it lies level within the body. Lay the Grill (B7) and Griddle (B8) into place. Configuration: Left — Cooking Grill, Right — Cooking Griddle NOTE: Ensure that the lava rock lies directly underneath the grills. Attach the Warming Rack (A3) to barbecue body as shown.
  • Page 11 • Repeat test • If bubbles form again do not use the barbecue and contact your local Outback distributor for assistance. Always wipe the mixed solution (½ water and ½ liquid detergent / soap) from all joints and connections after leak testing.

  • Page 12: Gas, Regulator And Hose

    Important Information Before you use your barbecue, perform a leak test. This is the only safe and sure way Please read these instructions carefully to detect any gas leaking from joints and before assembly and use of your barbecue. connections of the barbecue after assembly. Leak test annually, and whenever the gas Retain these...

  • Page 13: Installation

    WARRANTY. Please consult your local gas Full coverage will cause excessive build-up dealer for the most suitable gas bottles and of heat and damage the barbecue. This is regulators. not covered by warranty. Preparation Before Cooking Installation To prevent foods from sticking to the cooking surface, please use a long handled brush to Selecting a Location apply a light coat of cooking or vegetable oil...

  • Page 14: Cooking Grill

    or regulator. on one side of the cooking grill. • Insert lit match through the right match- lighting hole on the right side of the Turn the burner directly under the food to the barbecue body and place near rightmost OFF position and turn all other burners to a LOW to MEDIUM position.

  • Page 15: Care And Maintenance

    given below. outside weather conditions or stored in damp, moist areas. Fat Fires Empty and clean the drip tray and drip pan (and Never handle hot parts with unprotected foil liner, if applicable) of food debris after each hands. cooking session. If the barbecue is to be used for Never douse the barbecue with water when large gatherings, it will be necessary to turn off its surfaces are hot.
  • Page 16 The burners should be removed and cleaned powders as they can permanently damage the annually, or whenever heavy build-up is found, finish. to ensure that there are no signs of blockage (debris, insects) in either the burner portholes or Fixings the primary air inlet of the burners.

  • Page 17: Technical Specifications

    Technical Specifications NOTES: Heat Injector Burners Gas /Pressure Approval Input Size Outback® Meteor 0359 8.64 28-30 mbar Butane Select 3 0.84mm 359BR665 or 37 mbar Propane Burner Gas Gas Consumption: 628g/hr Countries of Use: BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT, LU, LV, PT,...

  • Page 18: Troubleshooting

    Troubleshooting Problem Possible Cause Solution Burner will not light using LP gas bottle is empty Replace with full bottle the ignition system Faulty regulator Have regulator checked or replaced Obstructions in burner Clean burner Obstructions in gas jets or gas hose Clean jets and gas hose Electrode or ignition button wire is loose Reconnect wire...
  • Page 19 (10) years from the date of purchase. Stainless steel and cast iron burners are warranted for a period of two (2) years from the date of purchase. OUTBACK will, within this period, supply replacements for defective parts free of charge provided that: ♦...

Table of Contents