Page 1
Product Family Quick Installation User's Guide Thank you for buying an Intel® Server System. The following information will help you assemble your Intel ® Server System and install components. If you are not familiar with ESD [Electrostatic Discharge] procedures used during system integration, see the complete ESD procedures described in your Service Guide.
Front Control Panel * 2.5" Hard Drive Bay system as shown Useful Information: • Riser Slot 2 is not functional without having two processors installed. • The SCU1 (4-7) port requires an Intel RAID C600 Upgrade Key installed to be functional. ®...
General Installation Process The installation instructions in this section are for common components of Intel® Server System R2000GZ/GL Product Family. Minimum Hardware Requirements Preparing the System To avoid integration difficulties and possible board damage, your system must meet the following minimum requirements: Observe normal ESD (Electrostatic Discharge) •...
General Installation Process Install the Processor(s) A. Open the Socket Lever B. Open the Load Plate Push down the lever and slide away from the socket to Press the locking lever slightly to raise the release it. load plate. Repeat step A to release the lever on the other side. Open the load plate all the way.
NOTE: For additional memory configurations, see the Service Guide on the Intel Server Deployment & Management DVD that accompanied your Intel ® ® Server System, or go to http://www.intel.com/support. Memory sizing and configuration is supported only for qualified DIMMs approved by Intel. For a list of supported memory, go to: http://serverconfigurator.intel.com.
General Installation Process Install Memory Modules ... Continued To Install DIMMs: CAUTION: Avoid touching contacts Open both DIMM socket levers. when handling or installing DIMMs. Note location of alignment notch. Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot. Push down firmly on the DIMM until it snaps into place and both levers close.
Page 10
General Installation Process Install Hard Drives ... Continued 3.5" Hard Drive Carrier (For system with 3.5" hard drive bay only) Remove the four screws securing the Remove the drive carrier by pressing the green button HDD interface bracket and remove the and opening the lever.
General Installation Process Install Optical Drive Install the plastic guide onto the back Insert the optical drive into chassis opening IMPORTANT NOTE: If you do not and push all the way until it stops. install a device at this location, of the drive and attach with two screws install the optical device bay filler as shown.
(optional) NOTE: Rack handles are required to install the bezel. For detailed instructions, see the product Squeeze the sides of the I/O module Service Guide available on the Intel Server ® Deployment & Management DVD. bay filler plate, and pull it away from the chassis back panel.
1. Verify the system top cover is installed. 2. Install the server into the rack using the instructions provided with the rack mounting kit. 3. Connect your USB keyboard/mouse, video and other I/O cables/devices NIC 2 NIC 4 Serial Intel ® RMM4 Intel ® as shown.
NOTE: The FRUSDR utility must be run for full platform management functionality. B. Configure your RAID Controller: If using a RAID card, use the instructions provided with the RAID controller. If using on-board RAID, you must activate RAID in the BIOS setup. See the Intel ®...
Chassis Intrusion System Fan 5 Fan 1 Fan 2 System Front Panel Fan 4 * - For server systems integrated with Intel® Server Board S2600GZ only. See your Intel Server System R2000GZ/GL Service Guide for expanded component and connection information. ®...
Page 16
Reference System Fan Connection FAN 1 FAN 2 FAN 3 FAN 4 FAN 5 A complete list of accessories and spares can be found at http://www.intel.com/support.
Reference System Cabling Diagram For system with 8 x 3.5” hard drive bay: NOTES: To activate the port SCU1 (4-7) on the server board, a proper Intel RAID C600 Upgrade Key must be installed. For instructions, see Intel RAID C600 ®...
Page 18
Reference System Cabling Diagram For system with 12 x 3.5” hard drive bay: Intel ® RAID ® Intel Integrated Expander Card RAID Module RES2SV240 Power Supply Server Board Interposer Board 12 x 3.5" HSBP...
Page 19
Reference System Cabling Diagram For system with 8 x 2.5” hard drive bay: NOTES: To activate the port SCU1 (4-7) on the server board, a proper Intel RAID C600 Upgrade Key must be ® installed. For instructions, see Intel RAID C600 Upgrade Key Installation Guide.
Page 20
System Cabling Diagram For system with 16 x 2.5” hard drive bay: NOTE: A second SSD is supported when the optical drive is NOT in use. For cable routing, please refer to Page 17. ® Intel Integrated RAID Module Power...
Page 21
Reference System Cabling Diagram For system with 24 x 2.5” hard drive bay: NOTE: To activate the port SCU1 (4-7) on the server board, a proper Intel RAID C600 Upgrade Key must be ® installed. For instructions, see Intel RAID C600 Upgrade Key Installation Guide.