Yamaha F100C Service Manual page 339

Good working practices ..............................1-4
H.
Hose routing................................................4-2
How to use this manual...............................1-1
I.
Identification................................................1-5
Ignition system ................................ 1-11
Ignition system and ignition control
system.......................................................8-7
Ignition timing control ................................1-18
Installing the clamp brackets........... 7-27
Installing the cylinder head .......................5-34
Installing the drive shaft .................. 6-20
Installing the lower unit ................... 6-23
Installing the power trim and tilt motor ......7-47
Installing the power trim and tilt
unit ................................................ 7-51
Installing the power unit ............................5-51
Installing the propeller shaft
housing ......................................... 6-21
Installing the pump housing ......................7-41
Installing the sprockets and timing belt .....5-18
Installing the steering arm............... 7-23
Installing the tilt ram ..................................7-36
Installing the trim rams..............................7-34
Installing the upper case ................. 7-20
Installing the valves...................................5-33
Installing the water pump and
shift rod ......................................... 6-22
L.
Lower unit ................................1-15
Lower unit (F100B) .....................................6-4
Lower unit (F100C) ...................................6-31
Lubrication ................................................3-16
Lubrication system ....................................1-20
M.
Maintenance interval chart..........................3-2
Maintenance specifications.........................2-3
Manual format .............................................1-1
Measuring the forward and reverse gear
backlash..................................................6-29
Measuring the forward gear backlash.......6-56
Measuring the lower resistance ..................8-2
Measuring the peak voltage........................8-2
N.
Not installed .................................... 7-48
60C5D11
P.
Parts, lubricants, and sealants ................... 1-3
Power trim and tilt electrical system ......... 7-90
Power trim and tilt motor (F100B)............. 7-42
Power trim and tilt motor (F100C) ............ 7-86
Power trim and tilt unit .............................. 3-12
Power trim and tilt unit (F100B) ................ 7-29
Power trim and tilt unit (F100C)................ 7-69
Power unit.....................1-6
,
1-18
Predelivery checks ................................... 1-25
Propeller selection .................................... 1-25
Propeller shaft housing (F100B)................. 6-9
Propeller shaft housing (F100C)............... 6-37
,
7-67
Propeller size............................................ 1-25
PTT (power trim and tilt) unit (F100B) ...... 1-22
,
6-48
PTT (power trim and tilt) unit (F100C) ...... 1-24
,
6-51
R.
,
7-70
Refacing the valve seat ............................ 5-29
Removing and installing the oil filter ......... 5-39
Removing the clamp brackets .........7-27
,
6-49
Removing the cylinder head ..................... 5-25
Removing the drive shaft.................6-17
Removing the lower unit ....................6-7
,
7-64
Removing the power trim and tilt
unit.................................................7-30
Removing the power unit.......................... 5-10
,
7-62
Removing the propeller shaft housing
assembly .......................................6-11
Removing the starter motor pinion ........... 8-17
,
6-49
Removing the steering arm .............7-23
Removing the timing belt and sprockets... 5-17
Removing the water pump and
shift rod............................................6-8
, ,
2-6 3-13
Replacing the timing belt ............................ 3-7
Replacing the valve guides....................... 5-28
S.
Safety while working................................... 1-3
Selecting the connecting rod big end bearing .
5-44
Selecting the crankshaft main journal bearing.
5-47
Selecting the forward gear shims ....6-27
Selecting the pinion shims...............6-26
Selecting the reverse gear shims ....6-28
Selection................................................... 1-25
Self-protection ............................................ 1-3
Serial number ............................................. 1-5
Shimming.........................................6-26
Shimming (F100B).................................... 6-25
,
7-88
Shimming (F100C) ................................... 6-53
1
, , , ,
2
2-3 3-5 5-3 9-1
3
4
,
7-67
,
6-45
,
6-35
5
,
7-70
,
6-39
6
,
7-64
,
6-36
7
8
,
6-55
9
,
6-54
,
6-56
,
6-54
i-3