Advertisement
Note：Once the battery is disconnected, the loads are not protected
from power outages.
1.
Use an insulated philip screwdriver to remove the four screws located
at the base of the UPS.
2.
Remove the front panel and top cover.
3.
Use an insulated philip screwdriver to remove the two screws from the
battery holding plate. (for 1500L/1800L/2200L only)
4.
Disconnect the battery cable terminals before removing the battery
from the UPS.
Step1: Loosen the black cable from the negative (-) terminal.
Step2: Loosen the red cable from the positive (+) terminal.
Refer to the steps below should the UPS fail to
function correctly
Step 1: Is the AC Mains switch in the "ON"
position?
Step 2: Is the UPS plugged into the AC power
supply?
Step 3: Is the power supply within specified
unit values?
Step 4: Has the fuse gone in the mains plug?
Step 5: Is the UPS overload?
Step 6: Is the battery flat or defective?
Description
Model
Capacity
Input
Voltage
Voltage Range
Output
Voltage Regulation
Transfer Time
Waveform
Battery
Type & Number
Charging time
Physical
Dimension (WxHxD, mm)
Net Weight (kg)
Packaging Dimension
(WxHxD, mm)
Gross Weight (kg)
Environment
Humidity
Noise level
Safety
Security certificate
REPLACING THE BATTERY
5.
Connect the battery cables to the terminals of the new battery.
Step1: Insert the black cable to the negative (-) terminal.
Step2: Insert the red cable to the positive (+) terminal.
Note: Small sparks at the battery connectors are normal during connection.
6.
Slide the battery into the UPS.
7.
Use an insulated philip screwdriver to fasten the two screws on the battery holding plate. (for 1500L/1800L/2200L only)
8.
Close the front panel and fasten the four screws located at the base of the UPS.
9.
Dispose off the old battery properly at an appropriate recycling facility.
STEP2
STEP1
800L/1000L
TROUBLESHOOTING
Situation
Problem / Possible Causes
Battery voltage is low.
No LEDs display on the front
Battery is defective.
panel.
The UPS is not turned on.
Alarm beeps continuously
The UPS is overloaded.
when the Utility is normal.
The UPS is overloaded.
UPS does not provide
expected backup time.
Battery voltage is too low.
Battery is defective.
The Utility is normal but LED
Power cord is loose.
is flashing.
Ablerex 800L / 1000L SPECIFICATIONS
800L
1000L
800VA
1000VA
12V/7Ah x 1
12V/9Ah x 1
100 x 140 x 292
5
137 x 226 x 321
5.5
STEP1
STEP2
Charge the UPS at least 6 hours.
Replace the battery with the same capacity.
Press the power switch again to turn on the UPS.
Remove some loads/equipment first. The connected equipment exceeds the
UPS specified 'capacity/load".
Remove some loads/equipment first. The connected equipment exceeds the
UPS specified 'capacity/load".
Charge the UPS at least 6 hours.
Replace the battery with the same capacity.
Reconnect the power cord properly.
Ablerex 1500L / 1800L / 2200L SPECIFICATIONS
1500L
1500VA
220/230/240VAC
160~290Vac
+/- 10%
Typical 2-6ms, 10 ms max.
Simulated Sine Wave
12V/7Ah x 2
4-6 hours recover to 90% capacity
5.5
9
6
10
0-90 % RH @ 0-40 C (non-condensing)
Less than 40 dB
CE
2
1500L/1800L/2000L
Solution
1800L
22000L
1800VA
2200VA
12V/7Ah x 2
12V/9Ah x 2
148 x 198 x 315
10.5
11.8
229 x 302 x 411
11.5
12.8
Advertisement
