Sony Trinitron BVM-F24E Operation Manual page 98

A Preset Adjustment of the Picture Level Control Knobs
— CONTROL PRESET ADJ Menu
[A1] PRESET menu/CH SET menu
Select the setting method.
MANUAL... : Set with the MANUAL knobs. k[A11]
AUTO... : Set by automatic adjustment. k[A12]
COPY FROM... : Copy data from elsewhere.
k[A13]
[A2] MATRIX menu
Select the matrix of HD-SDI signals. When
VARIABLE is selected in this menu, by carrying out
the AUTO menu (AUTO SET UP adjustment), the
matrix can be set according to the color bar signal.
Notes
• When PRESET is selected, the ITU709 is set.
• When VARIABLE is selected, carry out the AUTO
menu (AUTO SET UP adjustment). k[A12]
[A11] MANUAL menu
Adjust values by turning the BRIGHT and/or
CONTRAST knobs. After the adjustment, press the
ENTER or Ent button to confirm the adjusted values.
BRIGHT: xxxx
CONTRAST: xxxx
When you want to erase characters from the screen
while adjusting manually
Press the [F1] button. The characters disappear. To
display characters, press the [F1] button again.
To reset the setting to the default
Press the corresponding MANUAL button. The
adjusted value is reset to default.
Notes
When the PC signals (Analog RGB), SXGA/75 Hz or
SXGA/85 Hz signals are selected, the setting value of
CONTRAST is displayed up to MAX2000 (+1000)
However the actual setting value is up to around 1500
1)
(+0500) . Even if you set CONTRAST to more than
around 1500 (+0500), the contrast is not variable.
1)
The CONTRAST value shows when CONT/BRT
CENTER is set to 1000 or 0000 (the value in the
parentheses).
For details of the CONT/BRT CENTER setting, see "[C4]
Setting the Channel Selection Method and Power-Up
Conditions (SET UP4)  SYSTEM CONFIGURATION
Menu" (on page 40).
[A12] AUTO menu (AUTO SET UP adjustment)
Select the color bar signal to be used for automatic
adjustment. k Adjustment is carried out.
8COLOR BAR 100%: 100% full-field 8-color bar
(white, yellow, cyan, green, magenta, red, blue
and black)
22
8COLOR BAR 75%: 75% full-field 8-color bar
(with 100% white signal)
7COLOR BAR 100%: 100% full-field 7-color bar
(white, yellow, cyan, green, magenta, red and
blue) (with 100% white signal)
HDW COLOR BAR: The quasi SMPTE color bar for
HD (selectable when 1920 × 1080 signal is input).
[A13] COPY FROM menu
Select the source to be copied from.
OTHER VALUE... : Copy data from another channel
or common data. k[A131]
OTHER MONITOR... : Copy data from another
monitor. k[A132]
MEMORY CARD... : Copy data from a memory card.
k[A133]
[A131] OTHER VALUE menu
Choose either PRESET or CH SET.
k Copy is carried out.
PRESET: Copy common data.
CH SET: Copy data set for another channel. Input the
number of the channel from which the data will be
copied.
[A132] OTHER MONITOR menu
Input the address of the monitor from which the data
will be copied. k [A1321]
MONITOR ADDRESS: Input the address number.
[A1321] MONITOR ADDRESS menu
Choose either PRESET or CH SET.
k Copy is carried out.
PRESET: Copy common data.
CH SET: Copy data set for another channel. Input the
number of the channel from which the data will be
copied.
1)
.
[A133] MEMORY CARD menu
Select the file name. k [A1331]
FILE NAME: Select the file name.
Note
The input signal is not displayed during the data
loading.
[A1331] FILE NAME menu
Choose either PRESET or CH SET.
k Copy is carried out.
PRESET: Copy common data.
CH SET: Copy data set for another channel. Input the
number of the channel from which the data will be
copied.