Exchange Two Entire Tracks (Swapwholetrk); Swapping Entire Tracks; Fade-In/Fade-Out (Fadetrk); Creating A Fade-In - Korg D3200 Owner's Manual

Exchange two entire tracks (SwapWholeTrk)

This command exchanges an entire track of recorded data
(from the beginning to the end) with another track.
• You can exchange one or more tracks in a single operation.
This can be used in ways such as the following.
• Rearrange recorded tracks to organize them by type.
• Rearrange data that extends across differing virtual tracks
so that each track uses (for example) virtual track "A."
• Place two tracks that were recorded separately into adja-
cent tracks so that they can be paired.

Swapping entire tracks

Swapping track 1 virtual track "A" with track 2 virtual
track "B"
(1) Select the source track that you want to swap.
In the TRACK, "Vtrk1–32" tab page, select track 1 vir-
tual track "A."
(2) Select the destination track that you want to swap.
In the TRACK, "Vtrk1–32" tab page, verify that track 2
virtual track "B" is the track you want to swap.
(3) Select "SwapWholeTrk."
In the TRACK, "EditTrk" tab page, click the Edit Trk
Type cell. In the Edit Trk Type dialog box, choose
"SwapWholeTrk" and click the OK button (or press the
panel YES key).
(4) (3)
(4) Select the swap-source track number.
Click the popup button of the Source cell, and choose
track "1" in the Source Track dialog box. You can also
click the cell to select this.
(5) Select the swap-destination track number.
Click the popup button of the Destination cell, and
choose track "2" in the Destination Track dialog box.
You can also click the cell to select this.
If you specified two or more tracks as the "Source," you must
specify the same number of tracks in "Destination."
(6) Select the swap-destination virtual track.
In the Virtual cell, select virtual track "B".
(7) Execute the editing operation.
Click the Exec. button. Then in the SwapWholeTrk dia-
log box, click the Yes button (or press the panel YES key)
to execute the operation.
When the operation is finished, the display will indicate
"Completed." Click the OK button (or press the panel
YES key).
(8) In the TRACK, "Vtrk1–32" tab page, select virtual
track "B" for track 2.
(9) Check the results of the editing operation.
Play back from the beginning of the song to verify that
the swapping was performed correctly. In the same way,
check the "Source" track 1 virtual track "A" as well.
If you are not satisfied with the results, you can use
Undo to return to the previous state. (→p.141)
In this case, return the track 1 virtual track selection to "A."
76
(5)
(6)
(7)

Fade-in/fade-out (FadeTrk)

This command fades-in or fades-out the specified region
(IN–OUT) of recorded track data. By using both of these op-
erations, you can create cross-fades.
• You can fade-in or fade-out one or more tracks simultane-
ously.

Creating a fade-in

Fading-in the IN–OUT region of track 1
(1) Specify the region that you want to fade-in.
Set the following locations to specify the region where
the fade-in will occur (→p.69).
• Set the IN point to specify the beginning of the region
where the fade-in will occur.
• Set the OUT point to specify the end of the region
where the fade-in will occur.
(2) Select "FadeTrk."
In the TRACK, "EditTrk" tab page, click the Edit Trk
Type cell. In the Edit Trk Type dialog box, click "Fade-
Trk" and click the OK button (or press the panel YES
key).
(3) Select the fade-in curve.
Click the Mode button to display the Fade Mode dialog
box.
A.B.C: Fade-in curve
D.E.F: Fade-out curve
For details on how these curves differ, refer to "Fade-
Trk" (→p.133).
For this example, select the type "A" curve and click the
OK button (or press the panel YES key) to return to the
"EditTrk" tab page.
(4) Select the track number that you want to fade-in.
• Click the popup button of the Destination cell, and
choose track "1" in the Destination Track dialog box.
You can also click the cell to select this.
• Check the IN and OUT locations. If you want to set
the locations with more precision, click the Destina-
tion WAVE button, and use the Wave dialog box
(→p.128) to set the location.
(2)
(5) Execute the editing operation.
Click the Exec. button. Then in the FadeTrk dialog box,
click the Yes button (or press the panel YES key) to exe-
cute the operation.
When the operation is finished, the display will indicate
"Completed." Click the OK button (or press the panel
YES key).
(6) Check the results of the editing operation.
Press the LOC 1/IN key, and play back from the IN loca-
tion to verify that the fade-in performs correctly.
If you are not satisfied with the results, you can use
Undo to return to the previous state. (→p.141)
The length of the IN–OUT area specified will determine the
amount of time it takes to complete the Fade-in operation.
(4) (3)
(5)