Category: Sfx&Etc Sfx/Etc Effects - Korg D3200 Owner's Manual

26: Multiband Limiter
This is a stereo multi-band limiter. It is ideal for mastering.
Hi.Thresh (High Band Threshold)
Adjusts the level at which compression begins for the high-
Hi.Attack (High Band Attack)
Adjusts the attack time for the high-frequency range
Hi.Release (High Band Release)
Adjusts the release time for the high-frequency range
Hi.OutGain (High Band Output Gain)
Adjusts the output gain for the high-frequency range
Md.Thresh (Middle Band Threshold)
Adjusts the level at which compression begins for the mid-
Md.Attack (Middle Band Attack)
Adjusts the attack time for the mid-frequency range
Md.Release (Middle Band Release)
Adjusts the release time for the mid-frequency range
Md.OutGain (Middle Band Output Gain)
Adjusts the output gain for the mid-frequency range
Lo.Thresh (Low Band Threshold)
Adjusts the level at which compression begins for the low-
Lo.Attack (Low Band Attack)
Adjusts the attack time for the low-frequency range
Lo.Release (Low Band Release)
Adjusts the release time for the low-frequency range
Lo.OutGain (Low Band Output Gain)
Adjusts the output gain for the low-frequency range
Mon.Band (Monitor Band)
Lo.Xover (Low Cross over Frequency)
Sets the frequency of the crossover between the low and mid-
Hi.Xover (High Cross over Frequency)
Sets the frequency of the crossover between the mid and high-
Saturation (Tube Saturation)
Category: SFX&etc
SFX/Etc effects
27: St.Analog Record
(Stereo Analog Record)
RPM
Wah (Wah Flutter)
Sets the depth by which the record is warped
Bend
Sets the width by which the record is warped
Dry:Wet
Sets the balance between the effect and dry sounds
ClickLevel (Click Noise Level)
ClickAngle
Sets the angle of the scratch on the surface of the record
LoDamp (Low Damp)
158
–48.0...0.0dB
frequency range
–24.0...+24.0dB
–48.0...0.0dB
frequency range
–24.0...+24.0dB
–48.0...0.0dB
frequency range
–24.0...+24.0dB
Off, Low, Middle, High
Selects the band to monitor
53Hz...1.00kHz
frequency bands
1.10kHz...16.0kHz
frequency bands
Sets the depth of vacuum tube distortion
33 1/3, 45, 78
Sets the r.p.m. of a record
Dry, 1:99...99:1, Wet
Sets the level of click noise
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)
ClickPoint
Sets the distance of the scratch from the warped area
WhiteLevel (White Noise Level)
0...1.00sec
NoiseLoCut (Noise Low Cut)
0...10.0sec
NoiseHiCut (Noise High Cut)
Vinyl Level (Vinyl Noise Level)
Sets the level of noise produced by the needle scraping the vinyl
Vinyl Type (Vinyl Noise Type)
ClickAngle:
0...1.00sec
This sets the angle of the scratch. The spacing of the click noise
for one revolution will depend on the angle.
Vinyl Noise Type:
0...10.0sec
The Vinyl Noise will also depend on the amount by which the
record is warped.
28: Talking Modulator
This effect gives the input signal a character similar to a hu-
man voice. It can create the impression of a talking guitar or
0...1.00sec
synthesizer
0...10.0sec V.Bottom (Voice Bottom)
V.Centr (Voice Center)
V.Top (Voice Top)
Drive (Drive Gain)
Control (Control Source)
*LFO Speed
0...100%
Env.Resp (Envelope Response)
Env.Sens (Envelope Sensitivity)
L Delay (L Delay Time)
R Delay (R Delay Time)
*Manual (Manual Control)
Dry:Wet
Wet Trim (Wet Level Trim)
0...100%
29: St.Ring Modulator
0...100%
(Stereo Ring Modulator)
This effect creates a metallic sound by applying the oscilla-
tors to the input signal.
0...100%
Oscillator (Oscillator Frequency)
0...100
*LFO Speed
Sets the LFO speed of the oscillator frequency modulation
*LFO Depth
Sets the depth of LFO modulation for the oscillator frequency
53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Sets the level of white noise
THRU, 21Hz...8.00kHz
Sets the low-cut frequency for the noise
53Hz...20.0kHz, THRU
Sets the high-cut frequency for the noise
Selects the type of vinyl noise
Selects a vowel sound at the bottom end of control
Selects a vowel sound in the center of control
Selects a vowel sound at the top end of control
Sets the amount of gain for the distortion
Envelope, LFO, Manual
Switches the control source
Selects the response speed of envelope control
Sets the sensitivity of envelope control
Sets the left delay time
Sets the right delay time
Sets the control position manually
Sets the balance between the effect and dry sounds
Sets the effect level trim
Sets the oscillator frequency
0...100
0...100%
0...100%
0...3
[A], [E], [I], [O], [U]
[A], [E], [I], [O], [U]
[A], [E], [I], [O], [U]
0.0...+36dB
0.02...20.00Hz
Sets the LFO speed
Slow, Medium, Fast
0...100%
0...2.730sec
0...2.730sec
0...100
Dry, 1:99...99:1, Wet
0...100
0...12.00kHz
0.02...20.00Hz
0...100%