Related Manuals for LabelStation Pro200 series
Summary of Contents for LabelStation Pro200 series
- Page 1 © Advanced Labelling Limited July 2008 LabelStation Pro200/300 User Guide LabelStation Pro Series Set Up Manual July 2008...
-
Page 2: Table Of Contents
LabelStation Pro Series to PC Connection • Fig.4. Attach power supply to printer 2.2. Loading the Print Ribbon 2.2.1. Installing the Print Ribbon into the LabelStation Pro Series printer • Fig.5. Ribbon Installation 1 • Fig.6. Ribbon Installation 2 2.3. - Page 3 Printer Specifications 3.5.2. Label Stock Specifications 3.5.3. Ribbon Stock Specifications 3.5.4. Options 3.6. Compliances 3.7. Warranty Information 3.7.1. Thermal Print Head 3.7.2. Warranty Service Procedures 3.7.3. General Warranty Provision 3.7.4. Limitation of Liability LabelStation Pro Series Set Up Manual July 2008...
-
Page 4: Getting Started
The printer has been specially packaged to withstand damage in the shipping process. However, upon receiving the LabelStation Pro Series printer, carefully inspect the package and the device. In case of evident damage, contact Advanced Labelling Systems directly to specify the nature and extent of the damage. -
Page 5: Getting To Know Your Labelstation Pro Series
© Advanced Labelling Limited July 2008 1.3. Getting to Know your LabelStation Pro Series This section shows the various parts of the LabelStation Pro Series printer. We recommend that you familiarize yourself with these parts. 1.3.1. LabelStation Pro Series Printer External View 1. -
Page 6: Labelstation Pro Series Printer External Label Roll Mount
© Advanced Labelling Limited July 2008 1.3.3. LabelStation Pro Series External Label Roll Mount (optional) This is used when a larger diameter roll of labels or heat shrink tubing is being used (in excess of 100mm). The label mount sits behind the printer and the labels feed through a slot in the back of the printer. -
Page 7: Setting Up Your Labelstation Pro Series
If the ribbon is installed, but the printer is not winding it on, please refer to the ribbon calibration procedure to calibrate the ribbon sensor sensitivity. (Chapter 5.1.1. Ribbon Sensor Calibration) 2.2.1. Installing the Print Ribbon into the LabelStation Pro Series printer. • Push down on the ribbon access window to unlock and open the cover. •... - Page 8 © Advanced Labelling Limited July 2008 • Close the ribbon access window. LabelStation Pro Series Set Up Manual July 2008...
- Page 9 © Advanced Labelling Limited July 2008 Ribbon Access Window Paper Core Ribbon Spindle Back Hub Front Hub Fig.5. Ribbon Installation 1 Ribbon Supply Spindle Ribbon Leader Rear Hub Ribbon Rewind Paper Core Fig.6. Ribbon Installation 2 LabelStation Pro Series Set Up Manual July 2008...
-
Page 10: Loading Label Stock
To close the printer top cover, lift the cover to the ultimate open angle then use both hands to close the cover gently. Close the printer top cover slowly and make sure the cover locks latch securely. - 10 LabelStation Pro Series Set Up Manual July 2008... -
Page 11: Using The External Roll Holder
Install a roll of labels (loaded onto the label spindle) on the external paper roll mount. • Feed the labels through the external label feed opening through the rear paper guide. - 11 LabelStation Pro Series Set Up Manual July 2008... - Page 12 MAKE SURE THE LABELS ARE INSTALLED IN THE PRINTER SO THE LABELS ARE COMING OFF THE BASE OF THE ROLL NOT OFF THE TOP. THIS IS THE OPPOSITE OF THE DIAGRAM ON THE BASE - 12 LabelStation Pro Series Set Up Manual July 2008...
-
Page 13: Loading Labels With The Cutter Unit Attached (Optional)
Fig.13. Label installation in cutter mode • Close the top cover by lifting up the top cover support and close the top cover slowly Fig.14. Complete label installation in cutter mode - 13 LabelStation Pro Series Set Up Manual July 2008... -
Page 14: Closing The Top Cover
• Use both hands to gently push down the top cover to close it and make sure the cover is latched on both sides. Fig.16. Top cover is fully open and ready to close - 14 LabelStation Pro Series Set Up Manual July 2008... - Page 15 Do not force the cover! If you are not sure if top cover is fixed at stop position, please do not push top cover to close it or the top cover will be damaged. - 15 LabelStation Pro Series Set Up Manual July 2008...
-
Page 16: Labelstation Pro Series Specifications
Calibrate label pitch • Print out thermal print head check pattern • Print out the internal settings • Enter dump mode Reset the printer by turning the POWER switch off and on. - 16 LabelStation Pro Series Set Up Manual July 2008... -
Page 17: Self Test Printout
The characters received will be shown in the first column, and their corresponding hexadecimal values, in the second. This is often helpful to users for the verification of programming commands or debugging of printer programs. - 17 LabelStation Pro Series Set Up Manual July 2008... -
Page 18: Printer Initialisation
8 data bits, 1 stop bit Code Page Country Code Clear Flash Memory Note: When printer initialization is done, please calibrate the gap sensor again – see 5.1.2 Gap Sensor Calibration Utility. - 18 LabelStation Pro Series Set Up Manual July 2008... -
Page 19: Maintenance
Exterior Wipe it with water-dampened cloth. Interior Brush or air blow 3.3. Troubleshooting This section lists the common problems you may encounter when operating the LabelStation Pro Series printer. Also, it provides solutions. 3.3.1. LED Status LED Status/Colour Printer Status Solution Number 5.3.1.1. -
Page 20: The Printer Is Out Of Labels Or Ribbons Or The Printer Setting Is Not Correct
Emailed requests for support should be directed to info@labelzone.co.uk Our technical support is available to you during working hours, please call with any problems you may have. Tech Support Line – 01202 683212 - 20 LabelStation Pro Series Set Up Manual July 2008... -
Page 21: Led & Button Operation
Release the button when LED turns green after 5 orange flashes. (Any green will do during the 5 flashes). • Always do gap/black mark sensor calibration after printer initialization. - 21 LabelStation Pro Series Set Up Manual July 2008... -
Page 22: Specifications And Warranties
Centronics. Power AC input: 100-240V universal auto switching power supply. DC output: 24V 3.75A. Note: Use only the LabelStation Pro Series power supply; failure to do so could cause serious damage to the LabelStation Pro Series printer. Firmware Font Type 8 alpha-numeric bitmap fonts, and 1 true type font. -
Page 23: Label Stock Specifications
© Advanced Labelling Limited July 2008 3.5.2. Label Stock Specifications LabelStation Pro Series is capable of printing on a wide range of media. Refer to the supplies price list for specifications of compatible label media. Item Specification Type Label (Continuous, Die-cut, Fan-fold). -
Page 24: Compliances
Advanced Labelling Systems warrants to the customer, that under normal use and service, the LabelStation Pro Series printer (with the exception of the print head) purchased hereunder shall be free from defects in material and workmanship for a period of one year, from the date of shipment by Advanced Labelling Systems.