Table of Contents
Advertisement
Quick Links
MIG/MAG WELDING MACHINES
Content:
1.
INTRODUCTION ............................................................................................. 2
2.
SAFETY INSTRUCTIONS AND WARNINGS ....................................................... 2
3.
CONDITIONS OF USE ...................................................................................... 6
4.
TECHNICAL DATA ........................................................................................... 7
5.
ACCESSORIES ................................................................................................. 7
6.
DESCRIPTION OF THE APPLIANCE .................................................................. 8
7.
GETTING STARTED ....................................................................................... 10
8.
WELDING ..................................................................................................... 13
9.
ROUTINE MAINTENANCE & INSPECTION ...................................................... 14
10. STATEMENT OF WARRANTY ........................................................................ 14
11. DISPOSAL ..................................................................................................... 15
ALFA IN a.s. © 2013
PEGAS 250 MIG MAN
PEGAS 320 MIG MAN
INSTRUCTION MANUAL
www.alfain.eu
PEGAS 250-320 MIG MAN manual EN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alfa IN PEGAS 250 MIG MAN
Summary of Contents for Alfa IN PEGAS 250 MIG MAN
-
Page 1: Table Of Contents
MIG/MAG WELDING MACHINES PEGAS 250 MIG MAN PEGAS 320 MIG MAN INSTRUCTION MANUAL Content: INTRODUCTION ..................... 2 SAFETY INSTRUCTIONS AND WARNINGS ............2 CONDITIONS OF USE ..................6 TECHNICAL DATA ................... 7 ACCESSORIES ....................7 DESCRIPTION OF THE APPLIANCE ..............8 GETTING STARTED .................. -
Page 2: Introduction
Page 2 of 15 INTRODUCTION Congratulations on your new ALFA IN product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This Operating Manual has been designed to instruct you on the correct use and operation of your ALFA IN product. - Page 3 Noise can cause permanent hearing loss. Welding arc processes can cause noise levels to exceed safe limits. You must protect your ears from loud noise to prevent permanent loss of hearing. • To protect your hearing from loud noise, wear protective ear plugs and/or ALFA IN a.s. © www.alfain.eu...
- Page 4 Places without increased DC current: 113V AC current: 113V risk of electric shock peak value peak value and 80V effective Torches held DC current: 141V AC current: 141V mechanically with peak value peak value and ALFA IN a.s. © www.alfain.eu...
- Page 5 PROTECTIVE UTTILITIES • Welding helmet with filter shade at least 10 • Welding gloves • Welding apron and cloth • Welding boots RISK OVERVIEW • Risk of electric shock. • Ultraviolet light and light radiation ALFA IN a.s. © www.alfain.eu...
-
Page 6: Conditions Of Use
(see EN 60974-10). • The machine must be protected against a) moisture and rain and snow b) mechanical damage c) draft and any ventilation of neighbouring machine d) excessive overloading - crossing technical parameters e) rough handling ALFA IN a.s. © www.alfain.eu... -
Page 7: Technical Data
• Feed roll 0,8 - 1,0mm ACCESSORIES TO ORDER • Earthing cable 3 5 m with a clamp • Gas hose • Wire cleaner • CO2 Gas pre heating cable • Reduction valve • Gas cylinder ALFA IN a.s. © www.alfain.eu... -
Page 8: Description Of The Appliance
Torch ABIMIG AT 305-C LW 3m 018.D976.1 Torch ABIMIG AT 305-C LW 4m 018.D977.1 Torch ABIMIG AT 305-C LW 5m DESCRIPTION OF THE APPLIANCE MAIN PARTS Fig. 1 - Main parts EURO connector Voltage potentiometer ALFA IN a.s. © www.alfain.eu... - Page 9 = 10 mm b = 30 mm b = 30 mm Grove type Wire diameter Item No 0,6-0,8 2187 5434 Steel 0,8-1,0 2188 5435 1,0-1,2 2189 5436 0,8-1,0 2270 5437 Aluminium 1,0-1,2 2269 5438 ALFA IN a.s. © www.alfain.eu...
-
Page 10: Getting Started
B2 clockwise. • Plug the mains plug to 3x400 V mains. • Switch the machine on by the ON/OFF switch at the rear panel of the welder INSERTING THE WIRE Spool Holder Nut Spool Holder Adapter ALFA IN a.s. © www.alfain.eu... - Page 11 CHANGING THE WIRE FEEDER ROLL • Every wire feeding roll in ALFA IN machines can be used for two different diameters of welding wire – the rolls have two grooves. • When the machine is equipped with two roll wire feeder move the lever E1 to the right (2 roll feeder)/ forward (4 roll feeder).
- Page 12 Fig. 7 – Gas fitting. The picture is just for illustration. The portable PEGAS 250/320 MIG MAN are not equipped to support the gas cylinders. The gas cylinders must be well fitted in another gadget in accordance with the appropriate safety rules. ALFA IN a.s. © www.alfain.eu...
-
Page 13: Welding
To select the voltage potentiometer 2. To select the current (that is linked to the wire speed) use the voltage potentiometer 3 To modify the arc characteristic use the chope potentiometer 12. WELDING MODES Machines works in four modes: ALFA IN a.s. © www.alfain.eu... -
Page 14: Routine Maintenance & Inspection
ALFA IN welding products are manufactured for use by commercial and industrial users and trained personnel with experience in the use and maintenance of electrical welding and cutting equipment. • ALFA IN will repair or replace, at its discretion, any warranted parts or ALFA IN a.s. © www.alfain.eu... -
Page 15: Disposal
The warranty period begins on the date of sale to the end user. • If warranty is being sought, please contact your ALFA IN product supplier for the warranty repair procedure. • ALFA IN warranty will not apply to: •...
Need help?
Do you have a question about the PEGAS 250 MIG MAN and is the answer not in the manual?
Questions and answers