Subscribe to Our Youtube Channel
Related Manuals for Alfa IN PEGAS 40 PLASMA PFC
Summary of Contents for Alfa IN PEGAS 40 PLASMA PFC
- Page 1 PLASMA CUTTING MACHINE PEGAS 40 PLASMA PFC OPERATING MANUAL ALFA IN a.s © www.alfain.eu NA124-103...
-
Page 2: Table Of Contents
COMMENTS ON CONSUMABLES ..........12 GETTING STARTED................12 FIRST STEPS...................12 REQUIREMENTS FOR SOURCE OF COMPRESSED AIR....13 OPTIONAL AIR FILTERS ..............14 CUTTING..................14 IMPORTANT RULES................15 SOURCES OF POOR QUALITY CUTS ..........15 MAINTENANCE ..................16 STATEMENT OF WARRANTY ..............17 10. DISPOSAL .....................18 ALFA IN a.s © www.alfain.eu3... -
Page 3: Introduction
Manual represents the Manufacturer's best judgement, the Manufacturer assumes no liability for its use. Machine PEGAS 40 PLASMA PFC is designed for cutting metal on the basis of modern technology cutting material through a thin beam plasma gas. -
Page 4: Safety Instructions And Warnings
• Keep all fumes and gases from the breathing area. • Keep your head out of the fume plume. • Use an air-supplied respirator if ventilation is not adequate to remove all fumes and gases. ALFA IN a.s © www.alfain.eu3... - Page 5 The earthing of the piece being worked could increase the risk of injury to the operator. • EN 60974-1 Standard: Open-circuit voltage. During the operation of the machine, the highest voltage, with which it is possible to come into contact, ALFA IN a.s © www.alfain.eu3...
-
Page 6: Electromagnetic Compatibility (Emc)
• Domestic electronic appliances (radios, TVs, videos, telephones, burglar alarms, etc.). • Computers, robots, electro-medical instruments and life-support systems. • Radio-television transmitters and receivers. • Pacemakers and hearing aids. ALFA IN a.s © www.alfain.eu3... -
Page 7: Protective Uttilities
During installation, any electric work must only be carried out by trained personnel. • Do not expose the plasma machine to direct sunlight or to rain or snow. This equipment conforms to protection rating IP23S. ALFA IN a.s © www.alfain.eu3... -
Page 8: Technical Data
- crossing technical parameters e) rough handling TECHNICAL DATA PEGAS 40 PLASMA PFC Unit Plasma cutting Method V/Hz 1 x 110/50-60... -
Page 9: Operator Controls
2. LED illuminates and the air valve regularly opens and closes - the cutting tip and the electrode are not fitted properly. 3. LED flashes – there is not shield cup or the shield cup is ALFA IN a.s © www.alfain.eu3... -
Page 10: Accessories
Circular Cutting Attachment ABICUT 45 D640710 Filter for plasma DFP 6 R3/8 VM0328 Set for addition filter DFP to plasma S777a Light Reactive Welding Helmet ALFA IN S777 Circular Cutting Air Supply Adapter Quick connector Pegas Attachment ABICUT PEGAS Plasma 160/40 ALFA IN a.s ©... - Page 11 748.0059.1 Multi key ABI25/45 748.0057.1 Cable bundle ABI45 Note – the bold items are equipped on the torch Recommended starting kit for the Torch: Pos. Item No Description 748.START Starting Kit for ABICUT 45 PEGAS ALFA IN a.s © www.alfain.eu3...
-
Page 12: Comments On Consumables
Before beginning work is necessary to connect the machine to the mains. (1 x 110-230 V, 50/60 Hz). • Check completeness of the mounted cutting torch. • Connect the compressed air quick connector to the connector on the rear wall of the machine. ALFA IN a.s © www.alfain.eu3... -
Page 13: Requirements For Source Of Compressed Air
Maximal size of solid particles 15 microns • The minimal size of an air tank is 50 l • No additional oiling if the pressure air is permitted. That could damage the plasma machine and the cutting torch. ALFA IN a.s © www.alfain.eu3... -
Page 14: Optional Air Filters
(see Figure 3). This workflow must always be followed, if the thickness of material is above ALFA IN a.s © www.alfain.eu3... -
Page 15: Important Rules
Unplug the machine from the mains before any intervention inside the machine. • PEGAS 40 PLASMA PFC is adapted for use with torch ABICUT 45. This combination comply with EN 60974-7 Article 10.1.4. Using any other type and design of a torch must be approved by ALFA IN a.s. -
Page 16: Maintenance
Special maintenance is not necessary for the control unit parts in the plasma cut machine. If these parts are damaged for any reason, replacement is recommended. CAUTION • Do not blow air into the plasma cut during cleaning. Blowing air into the ALFA IN a.s © www.alfain.eu3... -
Page 17: Statement Of Warranty
• ALFA IN will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. The warranty period begins on the date of sale to the end user. -
Page 18: 10. Disposal
-18- necessary to ensure trouble free operation. NOTE • Warranty repairs must be performed by either an ALFA IN Service Centre, an ALFA IN distributor or an Authorised Service Agent approved by the company ALFA IN. 10. DISPOSAL Only for EU countries. Do not dispose of electric tools together with household waste material.
Need help?
Do you have a question about the PEGAS 40 PLASMA PFC and is the answer not in the manual?
Questions and answers