1. Manuals
  2. Brands
  3. Lightspeed Manuals
  4. Microphone system
  5. DELTA PA
  6. User manual

Lightspeed Delta PA User Manual

Hide thumbs Also See for Delta PA:
Table of Contents

Advertisement

Quick Links

Download this manual
DELTA PA
U s e r M a n u a l

Advertisement

Table of Contents
loading

Related Manuals for Lightspeed Delta PA

Summary of Contents for Lightspeed Delta PA

  • Page 1 DELTA PA U s e r M a n u a l...

  • Page 3: Table Of Contents

    Installing or Replacing Receiver Module SECTION 2: Step 1. Connecting the DELTA PA Receiver to a Power Supply Set-up & Use Step 2A. Setting up one DELTA PA Receiver Step 2B. Using More Than One DELTA PA Receiver Handheld Transmitter Step 3. Channel Selection Step 4.

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Read these instructions. 12. Use only with a cart, stand, tripod, bracket or table Keep these instructions. specified by the manufacturer, Heed all warnings. or sold with the apparatus. When a cart is used, use Follow all instructions. caution when moving the Do not use the apparatus near cart/apparatus combination to...

  • Page 5: Overview

    SECTION 1: OVERVIEW SYSTEM COMPONENTS AND UNPACKING The standard configuration of the DELTA PA will contain: DELTA PA Public Address System and Power Supply DELTA PA Carry Case...

  • Page 6: Optional Components

    OPTIONAL COMPONENTS Optional equipment which may be part of your DELTA PA system: BP016 Transmitter and Charger 831S Audio -Technica 831 TK250S Noise- Lapel Mic Cancelling Headset Microphone HM016 Transmitter Individual Components DPA016R 16 Channel UHF Receiver Module HM016 16 Channel UHF Handheld Transmitter...
  • Page 7 TOP PANEL: WIRELESS RECEIVER CONTROLS RECVR 2 RECVR 2 POWER/ RECVR 1 POWER RED: LOW BATT GREEN: ON CHARGE RED: CHARGING GREEN: FULL RECVR 1 1. WIRELESS RECEIVER 1: One or 5. TRANSMITTER LOW BATTERY INDICATOR: This LED will light two wireless receiver modules are located at the top panel.
  • Page 8 Charge. Red = Charging the treble setting. If you hear low- pitched howling, lower the bass *Note: Internal Delta PA lithium setting. ion battery must be replaced by licsensed Lightspeed service 3. AUX IN/MIC IN: Controls the center.

  • Page 9: Rear Panel Controls And Connections

    [NOTE: replacement is a 3.15A SB signal, while fully clockwise 250V slow blow fuse.] represents a line level signal. 8. DC POWER: This jack provides 5. AUX OUT: This ¼” jack provides a connection for the DELTA PA power supply.
  • Page 10 INSTALLING OR REPLACING A RECEIVER MODULE NOTE: Make sure the DELTA PA is turned off. 1. Remove the two screws securing the module panel using a small phillips head screwdriver. 2. Remove the module from the enclosure by carefully inserting...

  • Page 11: Set-Up & Use

    SECTION 2: SET-UP & USE 1. CONNECTING THE DELTA PA RECEIVER TO A POWER SUPPLY Note: When the DELTA PA is received, plug in the power supply and let charge overnight before using. 1. Locate the power supply. 2. Insert the DC connector into the “POWER INPUT”...
  • Page 12 RECVR 2 2A. SETTING UP ONE DELTA PA RECEIVER RECVR 2 RECVR 2 1. Turn the DELTA PA ON by rotating POWER/ RECVR 1 the POWER/RCVR 1 knob POWER RECVR 2 clockwise. The green LED will RED: LOW BATT GREEN: ON...
  • Page 13 2B. USING MORE THAN ONE DELTA PA RECEIVER If you have a second DELTA PA: A) Verify that RECVR 1 transmitter and receiver 1 are on and set to the same clear channel. B) Make sure the transmitter for RECVR 2 is turned off.
  • Page 14 3. CHANNEL SELECTION: HANDHELD TRANSMITTER Once a channel has been selected on the receiver, you now need to select that same channel on the handheld transmitter. If you have a belt-pack transmitter, go to page 19 for channel selection instructions. Same Channel 1.
  • Page 15 Use only AA NiMH batteries when recharging. NOTE: Do not mix battery types. WARNING: Do not use NiCad batteries! They will not charge properly and may cause damage to the transmitter. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work.
  • Page 16 3. Note the polarity in the battery compartment. IMPORTANT: Replace batteries with the same type, (alkaline or NiMH), that were installed in your Handheld Microphone. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work properly.
  • Page 17 A full charge will be attained in 8-10 hours. Fully charged Lightspeed microphones will last over 7 hours. WARNING: Do not attempt to charge alkaline batteries. They can overheat and expand, creating a significant hazard and damaging the transmitter.
  • Page 18 To remove, press the black button on the microphone connector and pull out. Microphone Options Lightspeed offers two types of microphones that can be used with this system. The BP016 Transmitter can be used with either a lapel style microphone or a headset microphone.
  • Page 19 8. CHANNEL SELECTION: BELT-PACK TRANSMITTER Channel Selection: Once a channel has been selected on the receiver, you now need to select that same channel on the belt- pack transmitter. 1. Turn the transmitter power on by sliding the PWR button to on. The LED will flash red.
  • Page 20 GT dial. Using a high impedance source requires a special cable. Contact Lightspeed Customer Service at 800-732- 8999 for more information. Customers in Canada should contact their local reseller.
  • Page 21 AA NiMH batteries when recharging. NOTE: Do not mix battery types. WARNING: Do not use NiCad batteries! They will not charge properly and may cause damage to the transmitter. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work.
  • Page 22 AA sized batteries. 3. Note the polarity in the battery compartment. IMPORTANT: Replace batteries with the same type, (alkaline or NiMH), that were installed in your belt-pack transmitter. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work properly.
  • Page 23 ONLY): Make sure there are NiMH recharge- able batteries in the transmitter before plugging in the charger. Fully charged Lightspeed transmitters will last over 7 hours. A full charge will be attained in 8-10 hours. WARNING: Do not attempt to charge alkaline batteries.

  • Page 24: Daily Use Instructions

    RED: CHARGING GREEN: FULL NOTE: Do not stand directly in front RECVR 1 of the DELTA PA speaker with the microphone on. This will result in feedback or ‘squealing.’ It is best to RECVR 1 stand behind or to the side of the unit when setting volume level.

  • Page 25: Optional Accessories

    SECTION 3: OPTIONAL ACCESSORIES HANDHELD MICROPHONE TRANSMITTER 1. RED LED: Lights up briefly when power is switched on, flashes continuously when audio is muted. 2. POWER ON/OFF: Turns the audio on and off. The red LED will flash when power is turned on. 3.
  • Page 26 BELT-PACK TRANSMITTER 1. ON/OFF BUTTON Provides adjustment for differing voice levels and microphone 2. RED LED: Lights up briefly when sensitivities. power is switched on. 8. MT (MICROPHONE GAIN): 3. MICROPHONE JACK: Provides adjustment for differing Microphone connects to levels of high impedance sources, transmitter here.
  • Page 27 3. Insert safety pin at an appropriate level. (see figure 1) figure 1 5. Place the Delta PA (DPA) amplifier upside down on a table top. 6. Locate the 3 screw holes on the botom of the amplifier. 7. Align the screw holes with the 3 holes on the bracket as shown in figure 2.

  • Page 28: Troubleshooting

    DELTA PA is turned on. If you review these instructions and still have questions, write down the serial number and model number of your system and call Lightspeed Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST. Customers in...

  • Page 29: Specifications

    Lightspeed Technologies’ option bulbs, or any other failings due to during the warranty period. For warranty service, please contact Lightspeed Customer Service Department to obtain return authorization approval and an RA number. Our Service Department (800.732.8999, 5 a.m. – 5 p.m., PST) will handle your repair/replacement needs.
  • Page 30 800.732.8999 authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). LABEL SPECIFICATIONS DELTA PA & BP016 & HM016 LABEL PART: 334-00118-00 ndustry anada...

  • Page 31: System Specifications

    SYSTEM SPECIFICATIONS OVERALL SPECIFICATIONS Nominal SPL [1W/1M] 89 dB Maximum SPL 102 dB 30 W at 2 Ω System Power [RMS] 40 W at 2 Ω Music Power [RMS] Amplifier Type Analog Class AB Frequency Response of amplifier 90 Hz - 18 kHz Full-Range 6.5”/4 Ω...
  • Page 32 SYSTEM SPECIFICATIONS CONT’D RECEIVER SPECIFICATIONS Carrier System Microprocessor Controlled PLL Synthesized Macro Frequency Range 620 to 679.75 MHz [3 Macro-Groups] Micro Frequency Range 25 MHz each Macro-Group Selectable Frequencies Deviation ± 40 KHz Nominal Sensitivity -100 dBm at S/N ratio of >80 dB Tone-code Frequency 32.768 KHz Image Rejection...
  • Page 33 LIGHTSPEE D TE CHNOLOGIES 11509 SW HERMA N ROA D / T UA LAT IN, OR 97062 TOLL FR EE: 800 .73 2.8 999 / PHON E: 503.684.5538 / FAX: 503.684.3197 L IGHTSPEED -TEK.COM MN0374US01-7...

Table of Contents