Dahua NVRPRO User Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Network Hardware
  5. NVRPRO
  6. User manual
Dahua NVRPRO User Manual

Dahua NVRPRO User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Network Video Recorder User's Manual
1

Advertisement

Table of Contents
loading

Related Manuals for Dahua NVRPRO

Summary of Contents for Dahua NVRPRO

  • Page 1 Network Video Recorder User’s Manual...
  • Page 2 Table of Contents ......................... 10 ..............................10 ..............................10 ............................11 ......................... 14 .............................. 14 ............................... 19 2.3.1 Device-end to PC-end........................22 2.3.2 PC-end to the device-end....................... 23 ............................ 23 ............................25 ............................31...

  • Page 3: Table Of Contents

    ............................32 ..............................33 ................................. 33 ............................ 34 ............................... 34 ..........................35 ............................... 38 6.5.1 HDD Information ..........................38 6.5.2 BPS ..............................39 6.5.3 Log ..............................40 6.5.4 Version .............................. 41 6.5.5 Online Users ............................. 41 ..............................42 6.6.1 General ............................. 42 6.6.2 Encode ..............................
  • Page 4 6.6.9 Display ............................... 63 6.6.10 Default ..............................64 ..............................65 6.7.1 HDD Management ........................... 65 6.7.2 Abnormity ............................68 6.7.3 Alarm Output ............................ 69 6.7.4 Manual Record ..........................69 Manual record menu ......................69 6.7.4.1 6.7.4.2 Basic operation ..........................69 Enable/disable record ......................
  • Page 5 8.2.4 Preview Window Switch ......................... 83 8.2.5 PTZ Control ............................83 8.2.6 Color and More Setup ........................85 ............................86 8.3.1 System Information ......................... 86 Version Information ........................ 86 8.3.1.1 HDD information ........................87 8.3.1.2 Log ............................87 8.3.1.3 8.3.2 System Configuration ........................
  • Page 8 Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. 2 Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
  • Page 10 It is a high performance network video recorder. This series product support local preview, multiple-window display, recorded file local storage, remote control and mouse shortcut menu operation, and remote management and control function. All these functions support this series product to be used in various situations.
  • Page 11 Through network, sending audio/video data compressed by IPC or NVS to client-ends, then the data will be decompressed and display. If bandwidth is big enough, latency is less than 500ms Network Support max 10 connections Monitor Transmit audio/video data by HTTP, TCP, UDP, MULTICAST, RTP/RTCP and etc.
  • Page 12 Operation Embedded Linux real-time operation system System Operation WEB/Local GUI Interface H.264/MPEG4 Video Compression For H.264, it max supports 16*D1, 8*720,4*1080P. Encode Capacity Audio G.711a Compression 1-channel VGA analog video output. Video Output 4/8/16-ch network compression digital video input Video Input 1-ch HDMI output.
  • Page 13 Network One RJ45 10/100M/1000M self-adaptive Ethernet port. Connection One power port, power adapter. Input Power Port DC 12V. One power button in the rear panel. Power Button One power button in the front panel. Power Button Remote Control Receiver Built-in clock. Clock 16 record status indication lights One power status indication light.
  • Page 14 2.1.1 1U Series The -1U series NVR front panel is shown as below. See Figure 2-1. Figure 2-1 Please refer to the following sheet for detail information. Name Icon Function Power button, press this button for three seconds to boot up or Power button shut down NVR.
  • Page 15 Go to menu Manually stop/start recording, working with direction keys Record or numeral keys to select the recording channel. Slow play Multiple slow play speeds or normal playback. One-window monitor mode, click this button to display assistant function: PTZ control and image color. Backspace function: in numeral control or text control, press it for 1.5seconds to delete the previous character before the cursor.
  • Page 16 Record light 1-16 It becomes on when system is recording. IR Receiver It is to receive the signal from the remote control. abnormity The red light is for the HDD abnormity indicator Network abnormity The red light is for the network abnormity indicator...
  • Page 17 2.2.1 1 U Series The 1U series NVR real panel is shown as in Figure 2-3. Figure 2-3 Please refer to the following sheet for detailed information. Port Name Connection Function USB port. Connect to USB mouse. Network port 10M/100M self-adaptive Ethernet port. Connect to the network cable.
  • Page 18 Port Name Connection Function 1-3-ch alarm NO1 NO3 3 groups of alarm output ports. (Group 1 output port port NO1 C1,Group 2:port NO2 C1 C3 C2,Group 3:port NO3 C3 ).Output alarm signal to the alarm device. Please make sure there is power to the external alarm device.
  • Page 19 Please refer to the following sheet for mouse operation instruction. Left click When you have selected one menu item, left click mouse to view menu content. mouse Modify checkbox or motion detection status. Click combo box to pop up dropdown list...
  • Page 20 In input box, you can select input methods. Left click the corresponding button on the panel you can input numeral/English character (small/capitalized). Here ← stands for backspace button. stands for space button. In English input mode: _stands for input a backspace icon and ← stands for deleting the previous character.
  • Page 21 The remote control interface is shown as in Figure 2-4 X282H282H282H Please note remote control is not our standard accessory and it is not included in the accessory bag. Figure 2-6 Please refer to the following sheet for detailed information. Serial Number Name Function...
  • Page 22 Next record In playback mode, playback the next video. Previous record In playback mode, playback the previous video. Play/Pause In pause mode, click this button to realize normal playback. In normal playback click this button to pause playback. In real-time monitor mode, click this button to enter video search menu.
  • Page 23 and Video color. Switch the PTZ control menu in PTZ control interface. In motion detection interface, working with direction keys to complete setup. 0-9 number key Input password, channel switch channel. Shift is the button to switch the input method. Figure 2-1...
  • Page 25 Please refer to the following figure for 2U series connection. Figure 4-1...
  • Page 26 The max. system capability that this product series supports is 16-CH standard definition with transmission rate 2mbps every channel or 4-ch high definition with transmission rate 8mbps. The delay time for switch-in is under 500ms every channel. Model System capability 4-ch series Max.
  • Page 27 Connect the device to the monitor, insert the mouse and connect the power cable. Push the on/off button in the rear panel and then you can see the analog video output. You can use the mouse to implement some simple GUI operation. Please refer to the following chapter for detail information. All the operations listed below are based on our 16-ch series device.
  • Page 28 Figure 6-2 After you logged in the device, right click mouse, you can see the short cut menu. Please see Figure 6-3. Here you can set local playback window, PTZ control, video color, search records, remote device and etc. The local playback window includes 1/4/9/16. You can set the detail channel amount in 1/4-window.
  • Page 29 Click search button in the main menu, search interface is shown as below. See Figure 6-5. Usually there are three file types: R: Regular recording file. A: External alarm recording file. M: Motion detection recording file Figure 6-5 Please refer to the following sheet for more information. Name Function Display...
  • Page 30 Playback mode 1/4/9/16. (It may vary due to different series.) In 1-window playback mode: you can select 1-16 channels. Playback In 4-window playback mode: you can select 4 channels according to your mode requirement. In 9-window playback mode, you can switch between 1-9 and 10-16 channels. channel In 16-window playback mode, you can switch between1-16 and 17-32 selection...
  • Page 31 Smart search The volume of the playback Click the snapshot button in the full-screen mode, the system can snapshot 1 picture per second. It is to display the record type and its period in current search criteria. In 4-window playback mode, there are corresponding four time bars. In other playback mode, there is only one time bar.

  • Page 32: Hdd Information

    When the system is in full-screen playback mode, left click the mouse in the screen. Drag your mouse in the screen to Digital zoom select a section and then left click mouse to realize digital zoom. You can right click mouse to exit. Note: All the operations here (such as playback speed, channel, time and progress) have relationship with hardware version.

  • Page 33: Bps

    Figure 6-7 In Figure 6-7, click view record d time button, HDD record time information interface is shown as in Figure 6-8. Figure 6-8 Parameter Function SATA 1-4 here means there are 4 HDDS. For 1U series product there are max 2 HDDs. For 2U series product there are max 8 HDDs.

  • Page 34: Log

    Figure 6-9 6.5.3 Log Here is for you to view system log file. System lists the following information. See Figure 6-10. Log types include system operation, configuration operation, data management, alarm event, record operation, log clear and etc. Please select start time and end time, then click search button. You can view the log files. System max displays 100 logs in one page.

  • Page 35: Version

    Figure 6-11 6.5.4 Version Here is for you to view some version information. See Figure 6-12. Channel Alarm in Alarm out System version: Build Date Serial number Figure 6-12 6.5.5 Online Users Here is for you manage online users connected to the local device. See Figure 6-13. You can disconnect one user or block one user if you have proper system right.

  • Page 36: General

    Figure 6-13 In main menu, highlight setting icon and double click mouse. System setting interface is shown as below. See Figure 6-14. Figure 6-14 Important Please note you need to have the proper right to implement the following operation. 6.6.1 General General setting includes the following items.
  • Page 37 Language: System supports various languages: Chinese (simplified), Chinese (Traditional), English, Italian, Japanese, French, Spanish (All languages listed here are optional. Slight difference maybe found in various series.) HDD full: Here is for you to select working mode when hard disk is full. There are two options: stop recording or rewrite.

  • Page 38: Encode

    Figure 6-17 6.6.2 Encode Encode setting includes the following items. See Figure 6-18. Please note some series do not support extra stream. Channel: Select the channel you want. Type: Please select from the dropdown list. There are three options: regular/motion detect/alarm.

  • Page 39: Schedule

    Figure 6-18 Figure 6-19 6.6.3 Schedule In the main menu, from setting to schedule, you can go to schedule menu. See Figure 6-20. Channel: Please select the channel number first. You can select “all” if you want to set for the whole channels.

  • Page 40: Rs232

    Figure 6-20 Shortcut settings: Users can copy the settings of channel A to channel B to achieve the same configuration effect.E.g. choose channel 1 and click the copy button after relevant settings are done, then paste to channel3, you can find that the configuration of channel3 is the same as that of channel1.

  • Page 41: Network

    Figure 6-21 6.6.5 Network Here is for you to input network information. See Figure 6-22. IP address: Here you can input IP address. DHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet mask /Gateway. These values are from DHCP function. If you have not enabled DHCP function, IP/Subnet mask/Gateway display as zero.

  • Page 42: Advanced Setup

    Figure 6-22 6.6.5.1 Advanced Setup Advanced setup interface is shown as in Figure 6-23. Please draw a circle to enable corresponding function and then double click current item to go to setup interface. Figure 6-23 6.6.5.2 IP Filter IP filter interface is shown as in Figure 6-24. You can add IP in the following list. The list supports max 64 IP addresses.

  • Page 43: Ntp Setup

    6.6.5.3 NTP Setup You need to install SNTP server (Such as Absolute Time Server) in your PC first. In Windows XP OS, you can use command “net start w32time” to boot up NTP service. NTP setup interface is shown as in Figure 6-25. Host IP: Input your PC address.

  • Page 44: Pppoe

    Figure 6-26 Here you can set a multiple cast group. Please refer to the following sheet for detailed information. IP multiple cast group address -224.0.0.0-239.255.255.255 -“D” address space The higher four-bit of the first byte=”1110” Reserved local multiple cast group address -224.0.0.0-224.0.0.255 -TTL=1 When sending out telegraph -For example...

  • Page 45: Ddns Setup

    Figure 6-27 6.6.5.6 DDNS Setup DDNS setup interface is shown as in Figure 6-28. You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In other words, this PC is a DNS (domain name server). In network DDNS, please select DDNS type and highlight enable item.
  • Page 46 Status: When the UPNP is offline, it shows as “Unknown”. When the UPNP works it shows “Success” Router LAN IP: It is the router IP in the LAN. WAN IP: It is the router IP in the WAN. The port mapping list here is the one to one relationship with the router’s Port Mapping list port mapping setting.

  • Page 47: Email

    Figure 6-30 6.6.5.8 Email The email interface is shown as below. See Figure 6-31. SMTP server: Please input your email SMTP server IP here. Port: Please input corresponding port value here. User name: Please input the user name to login the sender email box. Password: Please input the corresponding password here.

  • Page 48: Ftp

    Figure 6-31 Figure 6-32 6.6.5.9 FTP You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP service. Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> Serv-U Administator.

  • Page 49: Alarm Center

    Figure 6-34 System also supports upload multiple NVRs to one FTP server. You can create multiple folders under this FTP. In Figure 6-22, select FTP and then double click mouse. You can see the following interface. See Figure 6-35. Please highlight the icon in front of Enable to activate FTP function.

  • Page 50: Alarm

    6.6.6 Alarm In the main menu, from Setting to Alarm, you can see alarm setup interface. See Figure 6-37. Alarm setup: Alarm interface is shown as below. See Figure 6-37. Alarm in: Here is for you to select channel number. Event type: There are two types.
  • Page 51 Figure 6-37 Figure 6-38 Figure 6-39 Figure 6-40...

  • Page 52: Detect

    6.6.7 Detect Go to Detect Menu In the main menu, from Setting to Detect, you can see motion detect interface. See Figure 6-41.There is three detection types: motion detection, video loss, camera masking. Motion Detect Detection menu is shown as below. See Figure 6-41 Event type: from the dropdown list you can select motion detection type.
  • Page 53 Fn to switch between arm/withdraw motion detection. After setting, click enter button to exit. Figure 6-41 Figure 6-42 Figure 6-43...
  • Page 54 Figure 6-44 Figure 6-45 Video Loss In Figure 6-41, select video loss from the type list. You can see the interface is shown as in CFigure 6-46.This function allows you to be informed when video loss phenomenon occurred. You can enable alarm output channel and then enable show message function. Tips: You can enable preset activation operation when video loss occurs.

  • Page 55: Ptz

    Camera Masking When someone viciously masks the lens, or the output video is in one-color due to the environments light change, the system can alert you to guarantee video continuity. Camera masking interface is shown as in Figure 6-47. Tips: You can enable preset/tour/pattern activation operation when video loss occurs.
  • Page 56 Channel: select the current camera channel. Protocol: select corresponding PTZ protocol(such as PELCOD) Address: default address is 1. Baud rate: select corresponding baud rate. Default value is 9600. Data bits: select corresponding data bits. Default value is 8. Stop bits: select corresponding stop bits. Default value is 1. Parity: there are three options: odd/even/none.

  • Page 57: Display

    Figure 6-50 Here is a sheet for you reference. Name Function function Shortcut Function function Shortcut Zoom Wide ► Focus Near Iris Close Open 6.6.9 Display Display setup interface is shown as below. See Figure 6-51. Transparency: Here is for you to adjust transparency. The value ranges from 128 to 255. Channel name: Here is for you to modify channel name.

  • Page 58: Default

    Figure 6-51 In Figure 6-51, click modify button after channel. You can see an interface shown as in Figure 6-52. Please note all your modification here applies to local end only. You need to refresh web or client-end to get the latest channel name. System max support 25-digital character. Figure 6-52 In tour mode, you can see the following interface.

  • Page 59: Hdd Management

    Please highlight icon to select the corresponding function. After all the setups please click OK button, system goes back to the previous menu. Warning! System menu color, language, time display mode, video format, IP address, user account will not maintain previous setup after default operation! Double click advanced icon in the main window, the interface is shown as below.
  • Page 60 Figure 6-55 For the HDD group setup operation, please note: Each channel’s records can be stored into the specified HDD Group. Each HDD Group is corresponding to several hard disks, while one hard disk is only included in one HDD Group. Each channel is only corresponding with one HDD Group, while one HDD Group can store records from several channels.
  • Page 61 Figure 6-56 In Figure 6-57, you can see the 6th and 7th position hard disks both belong to HDD Group 2. Important Once you change the HDD Group settings, system will pack the records and snapshots, and then reboot. Figure 6-57 Channels Setting Click the button named with “Channels Settings”...

  • Page 62: Abnormity

    The Figure 6-58 and Figure 6-59 show that channels 1 to 16 are associated to HDD Group NO 1, and channels 17 to 32 are associated to HDD Group NO 2. Therefore the records of channels 1 to 16 are stored into the hard disk(s) which belong to HDD Group NO 1, and the records of channels 17 to 32 are stored into the hard disk(s) which belong to HDD Group NO 2.

  • Page 63: Alarm Output

    Figure 6-60 6.7.3 Alarm Output Here is for you to set proper alarm output. Please highlight icon to select the corresponding alarm output. After all the setups please click OK button, system goes back to the previous menu. See Figure 6-61.

  • Page 64: Enable/Disable Record

    There are three statuses: schedule/manual/stop. Please highlight icon to select corresponding channel. Manual: The highest priority. After manual setup, all selected channels will begin ordinary recording. Schedule: Channel records as you have set in recording setup (Main Menu->Setting->Schedule) Stop: All channels stop recording. Figure 6-62 6.7.4.3 Enable/disable record Please check current channel status: “○”...

  • Page 65: Stop All Channel Recording

    Figure 6-64 All channel manual record Please highlight “ALL” after “Manual.” See Figure 6-65. When system is in manual recording, all scheduled set up you have set in will be null ((Main menu->Setting->Schedule)). You can see indication light in front panel turns on, system begins manual record now. Figure 6-65 6.7.4.5 Stop all channel recording Please highlight “ALL”...

  • Page 66: Modify Password

    The user name and group name can consist of eight bytes. One name can only be used once. There are four default users: admin/888888/666666 and hidden user “default”. Except user 6666, other users have administrator right. Hidden user “default” is for system interior use only and can not be deleted. When there is no login user, hidden user “default”...

  • Page 67: Add/Modify Group

    Figure 6-68 6.7.5.2 Add/Modify Group Click add group button, the interface is shown as below. See Figure 6-69. Here you can input group name and then input some memo information if necessary. There are total 60 rights such as control panel, shut down, real-time monitor, playback, record, record file backup, PTZ, user account, system information view, alarm input/output setup, system setup, log view, clear log, upgrade system, control device and etc.

  • Page 68: Auto Maintenance

    6.7.6 Auto Maintenance Here you can set auto-reboot time and auto-delete old files setup. You can set to delete the files for the specified days. See Figure 6-71. You can select proper setup from dropdown list. After all the setups please click save button, system goes back to the previous menu. Figure 6-71 6.7.7 Remote Device The remote device interface is shown as in Figure 6-72.
  • Page 69 The configuration file backup interface is shown as below. See Figure 6-73. This function allows you to copy current system configuration to other devices. Figure 6-73 Double click shutdown button, system pops up a dialogue box for you to select. See Figure 6-74. Logout menu user: log out menu.
  • Page 70 Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. Double click the ConfigTools.exe icon, you can see an interface is shown as in Figure 7-1.
  • Page 71 Figure 7-2 Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 7-3. Figure 7-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set.
  • Page 72 Figure 7-5...

  • Page 73: Preparation

    The device web provides channel monitor menu tree, search, alarm setup, system setup, PTZ control and monitor window. Important The following operation is based on 16-channel series device. 8.1.1 Preparation Before log in, please make sure: Step1: PC and NVR connection is OK. Step2: You have set PC IP address, NVR IP address, subnet mask and gateway.
  • Page 74 Figure 8-2 IE Safety Setup After installation, the interface is shown as below. See Figure 7-3. Figure 8-3 Login interface Please input your user name and password. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login. NVR web main interface is shown as in Figure 7-4.

  • Page 75: Monitor Channel Menu Tree

    There are six sections: Section 1: Monitor channel menu tree Section 2: System menu Section 3: PTZ control Section 4: Video setup and other setup Section 5: Preview window Section 6: Monitor window switch 8.2.1 Monitor Channel Menu Tree The monitor channel menu tree is shown as in Figure 7-5. Figure 8-4 Monitor Channel Menu Tree Please refer to the following sheet for detailed information.
  • Page 76 Parameter Function CAM 1 to CAM channel 1 to channel 16 Click this button to open all video channels. Open all /close Once all video channels are open, it becomes close all button. Local play Click local play button to select file to play in PC. Refresh Click this button to refresh monitor channel name.

  • Page 77: System Menu

    8.2.2 System Menu System menu is shown as in .Figure 7-7. Please refer to chapter 7.3 Configuration, chapter 7.4 Search, chapter 7.5 Alarm, chapter 7.6 About, chapter 7.7 Log out for detailed information. Figure 8-6 System Menu 8.2.3 Monitor Window Switch The monitor window switch interface is shown as in Figure 7-8.
  • Page 78 You can click this icon to display or hide the PTZ control platform. Figure 8-9 PTZ Interface Click PTZ set button, the interface is shown as in Figure 7-11. Figure 8-10 PTZ Setup...

  • Page 79: Color And More Setup

    Please refer to the following sheet for PTZ setup information. Parameter Function Move the camera to you desired location and then click left limit Scan button. Then move the camera again and then click right limit button to set a right limit. Use direction keys to move the camera to your desired location and Preset then input preset value.

  • Page 80: System Information

    operation here It is to adjust monitor video contrast ness. applies to WEB end only. It is to adjust monitor video saturation. It is to adjust monitor video hue. Reset Restore system default value. Click more button, the interface is shown as in Figure 8-12. Figure 8-12 Color and More Please refer to the following sheet for detailed information.

  • Page 81: Hdd Information

    Figure 8-13 Version Information 8.3.1.2 HDD information Here you can view local storage status such as free capacity and total capacity. See Figure 8-14. Figure 8-14 HDD Information 8.3.1.3 Log Here you can view system log. See Figure 8-15...

  • Page 82: System Configuration

    Figure 8-15 Log Please refer to the following sheet for log parameter information. Parameter Function Log types include: system operation, configuration operation, data Type management, alarm event, record operation, user management, log clear and file operation. Set time to start search. Start time Set time to finish search Finish time...
  • Page 83 8-16 Figure 8-16. Figure 8-16 General Setup...
  • Page 84 Figure 8-17 DST Figure 8-18 DST Please refer to the following sheet for detailed information. Parameter Function Here is for you to modify system time. Please click Save button after System Time your completed modification Sync PC You can click this button to save the system time as your PC current time.

  • Page 85: Encoding Configuration

    8.3.2.2 Encode Figure 8-19 Parameter Function Channel Select the corresponding channel. Channel Display the current channel ID. You can also modify the channel ID here. Name Encoding The device does not support it. mode For the main stream, recorded file only contains video by default. You need to draw a circle here to enable audio function.

  • Page 86: Schedule

    Here you can privacy mask the specified video in the monitor video. One channel max supports 4 privacy mask zones. Overlay The privacy mask includes two options: Never/monitor. Never: It means do not (Cover area) enable privacy mask function. Monitor: the privacy mask zone can not be viewed in monitor mode.

  • Page 87: Rs232

    Figure 8-22 Copy Please refer to the following sheet for detailed information. Parameter Function Please select a channel first. Channel Pre-record Please input pre-record value here. When alarm record or motion detection record occurs, system can record the several seconds video before activating the record operation into the file.

  • Page 88: Network

    Figure 8-23 RS232 Please refer to the following sheet for detailed information. Parameter Function RS232 There is only one option COM 01, corresponding to RS232. Console is for debug. Function Control keyboard: Switch between RS232 and control keyboard. Network keyboard: COM control protocol. You can use network keyboard to control NVR via COM.

  • Page 89: Advanced Setup

    Figure 8-24 Network Please refer to the following sheet for detailed information. Parameter Function Ethernet Please select the network card first. DHCP Dynamically get IP address. You can get the device IP from the DHCP server if you enabled this function. Device ID The ID for recognition in network TCP Port...
  • Page 90 Figure 8-25 Network Function Parameter PPPOE Remote Input the user name and password which ISP(Internet service supplier) host provided and chose enable. Reboot system after configuration is saved and the device will auto connect to Internet. The IP address is the WAN IP. There are two conditions for reboot, 1.
  • Page 91 Figure 8-26 Email Please refer to the following sheet for detailed information. Parameter Function Input server address and then enable this function. SMTP Server You can also input the corresponding server domain name here, but you need to go to DNS interface (chapter 7.3.4.1) to set the server IP that can parse the domain.
  • Page 92 Figure 8-27 DDNS Please refer to the following sheet for detailed information. Parameter Function Server Type You can select DDNS protocol from the dropdown list and then enable DDNS function. The private DDNS protocol means you use our self-defined private protocol to realize DDNS function. Server IP DDNS server IP address Server Port...
  • Page 93 Figure 8-28 NAS Figure 8-29 NAS Setup Please refer to the following sheet for detailed information. Parameter Function Please select network storage protocol and then enable NAS enable NAS function. The network storage protocol includes FTP. Server IP Input remote storage server IP address. Input Remote storage server port number.
  • Page 94 Parameter Function Password The password you need to login the server. Remote Path Remote storage file path. Channel Select a monitor channel . Period In NAS interface, click set button, you can go to the info. corresponding setup interface. See Figure 7-29 Setup .Please set schedule period and then select corresponding record type: schedule/alarm.
  • Page 95 Parameter Function Enable Enable NTP function or not. Server IP Server IP address Port Server port. System supports TCP only and default port value is 123. Time Zone Device current time zone. Update Interval Time update interval value. Alarm Centre Alarm centre interface is shown as below.

  • Page 96: Alarm

    Figure 8-32 UNPN 8.3.2.6 Alarm Alarm setup interface is shown as in Figure 8-33. Figure 8-33 Alarm Setup...
  • Page 97 Figure 8-34 PTZ Setup Figure 8-35 Please refer to the following sheet for detailed information. Parameter Function Event It includes local alarm/network alarm/other. Type Local alarm: Device detects alarm from input port. Network: Device detects alarm from network. Alarm in Select corresponding alarm channel.

  • Page 98: Detect

    Parameter Function Period Alarm record function becomes activated in the specified periods. There are six periods in one day. Please draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole week.
  • Page 99 Figure 8-36 Detect Parameter Function Event type Motion detect, video loss and video masking Channel select the channel to activate recording function Sensitivity System supports 6 levels. The sixth level has the highest sensitivity. Enable button Tick to enable There are PAL22X18/NTSC22X15 small zones. Region Blue area is the detection zone.

  • Page 100: Ptz

    Parameter Function tour &pattern when there is an alarm. 8.3.2.2 PTZ PTZ interface is shown as in Figure 8-37 Please note, before operation please make sure you have set speed dome address and the NVR and speed dome connection is OK. Figure 8-37 PTZ Please refer to the following sheet for detailed information.

  • Page 101: Advanced

    Please note system can not restore some information such as network IP address. Figure 8-38 Default and Backup Please refer to the following sheet for detailed information. Parameter Function Select All Restore factory default setup. Export Export system configuration to local PC. Configuration Import Import configuration from PC to the system.
  • Page 102 Figure 8-39 HDD Management Please refer to the following sheet for detailed information. Parameter Function Format Clear data in the HDD. Read/write Set current HDD as read/write Read only Set current HDD as read. Redundant Set current HDD as redundant HHD. Recover Fix the HDD error.

  • Page 103: Abnormity

    8.3.3.2 Abnormity Parameter Function Event The abnormal events include: no disk, no space, disk error, offline, IP Type conflict. You need to draw a circle to enable this function. Threshold: It refers to the HDD free space.

  • Page 104: Alarm I/O

    Parameter Function Normal The corresponding alarm output channel when alarm occurs. For 1U series product, there are three channels. For 2U series product, there are six channels. The 6 channel is the controllable +12V alarm output. Latch The alarm output can delay for the specified time after alarm stops. The value ranges from 10s to 300s.

  • Page 105: Record

    Parameter Function Alarm output For 1U series product, there are three channels. For 2U series product, there are six channels. The 6 channel is the controllable +12V alarm output. Please click the corresponding number and then click the trigger button. Trigger Enable/disable alarm output.

  • Page 106: Account

    8.3.3.5 Account Here you can add, remove user or modify password. See Figure 8-42. Figure 8-42 Account Figure 8-43 Add user...

  • Page 107: Auto Maintenance

    Parameter Function User Input the user name of the new established account. Reusable The reusable account means that this account can be used in more than one PC at the same time. Password Input the password of the new established account. Confirm Input the password of the new established account again.

  • Page 108: Remote Device

    8.3.3.7 Remote device Figure 8-45 Remote device Parameter Function Channel Please select the local device channel number to connect to the remote device.. You need to highlight the enable item to activate this function. Now you can see remote device type, IP address and etc. Resolution type Choose the remote resolution type Please input remote device IP address, port number, remote device...

  • Page 109: Dns

    Figure 8-46 Auto register 8.3.4.2 DNS Here you can set server or local operator DNS address. See Figure 3-34. Once you input the domain name in SMTP server in the email interface (chapter 7.3.2.4 Network->email), you need to input the corresponding address here, otherwise the device can not parse the domain name.
  • Page 110 Click search button, you can see an interface is shown as in Figure 8-48. Please select record playback mode, and then select start time, end time and channel. Then please click search button, you can see the corresponding files in the list. Select the file(s) you want to download and then click download button, system pops up a dialogue box , and then you can specify file name and path to download the file(s) to your local pc.
  • Page 111 Type Parameter Function Alarm Search alarm record. Motion Search motion detection record. Detection This function is not available in current device. Local Search local record. Snapshot Search snapshot file. This function is not available in current device. Card This function is not available in current device. Parameters Start time Set the file start time.
  • Page 112 Figure 8-49 Alarm Please refer to the following sheet for detailed information. Type Parameter Function Alarm Video loss System alarms when video loss occurs. Type This function is not available in current device. Motion detection System alarms when motion detection alarm occurs, This function is not available in current device.
  • Page 113 Type Parameter Function Path Here you can specify alarm sound file. Click about button, you can view the web information. See Figure 7-47. Figure 8-50 About Click log out button, you can go back to log in interface. See Figure 7-48. Figure 8-51 Alarm...

Table of Contents