Installation Manual SPH-DA210 SPH-DA110 AppRadio...
Connecting the system • Do not route wires where they will be Precautions before exposed to high temperatures. If the connecting the system insulation heats up, wires may become damaged, resulting in a short circuit or WARNING malfunction and permanent damage to Do not take any steps to tamper with or the product.
Connecting the system To prevent damage WARNING • Use speakers over 50 W (output value) and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers ACC position No ACC position for this unit. • The black cable is ground. When • To avoid short-circuiting, cover the dis- installing this unit or power amp (sold connected lead with insulating tape.
Connecting the system Parts supplied Installing the HDMI cable holder ® 1 Insert the lower tab of the HDMI ca- ble holder into the groove of this prod- uct. Groove This product Power cord GPS antenna Microphone 2 Insert the two upper tabs into the this product by pushing the HDMI ca- HDMI cable holder ble holder.
Connecting the system Connecting the system This product 3.55 m Wired remote input (1 ft. 2 in.) Please refer to the instruction manual for the Hard-wired remote control adapter (sold separately). (13 ft. 1 in.) Vehicle antenna Microphone GPS antenna WARNING • To avoid the risk of accident and the potential violation of applicable laws, this product should never be used while the vehicle is being driven except for navigation purposes.
Connecting the system When connecting an iPhone with 30-pin USB interface cable for iPod / iPhone (*4) (sold separately) (6 ft. 7 in.) iPhone with 30-pin (*3) (*3) For details concerning operations and compatibility, refer to the Operation Manual. (*4) For details about how to connect the separately sold USB interface cable for iPod / iPhone (CD-IU201N), refer to the USB interface cable for iPod / iPhone manual.
Connecting the system When connecting an Android device with an MHL port USB - micro USB cable (*8) (Type USB A - micro USB B) USB cable (*8) (Type USB A - USB A) (sold separately) 1.5 m (4 ft. 11 in.) (sold separately) 0.75 m (2 ft.
Connecting the system Connecting the power cord (1) Yellow To terminal supplied with power regardless of ignition switch position. To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Orange/white To lighting switch terminal. Black (ground) To vehicle (metal) body. Notes • When a subwoofer is connected to this product instead of a rear speaker,...
Connecting the system This product Power cord Fuse (10 A) Blue/white To auto-antenna relay control terminal. If the vehicle has a glass antenna, connect to the antenna booster power control terminal (max. 300 mA 12 V DC).
Otherwise vehicle model. For details, consult you cannot switch to the rear view camera your authorized Pioneer dealer or picture. an installation professional. WARNING LIGHT GREEN LEAD AT POWER CONNECTOR IS...
Connecting the system When connecting to separately sold power amp/subwoofer Front outputs (FL, FR) This product Power amp (sold separately) RCA cables (sold separately) Power amp (sold separately) Subwoofer/rear outputs (SW/RL, SW/RR) Power cord System remote control Blue/white To system control terminal of the power amp (max.
Connecting the system This product When connecting a rear view camera When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the shift lever is moved to REVERSE (R). Rear View mode also allows you to check what is behind you while driving.
Installation • Do not install this product where it Precautions before may (i) obstruct the driver’s vision, (ii) installation impair the performance of any of the vehicle’s operating systems or safety CAUTION features, including airbags, hazard • Never install this product in places lamp buttons or (iii) impair the driver’s where, or in a manner that: ability to safely operate the vehicle.
Installation • When installing, to ensure proper heat Installing this product dispersal when using this unit, make Installation notes sure you leave ample space behind the rear panel and wrap any loose cables so • Do not install this product in places sub- they are not blocking the vents.
Installation Parts supplied Installation using the screw holes on the side of this product 1 Fasten the unit to the factory radio- mounting bracket. Position this product so that its screw holes are aligned with the screw holes of the brack- et, and tighten the screws at three or four lo- The display unit Truss head screw...
Installation Installing the GPS antenna Parts supplied CAUTION Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or mal- GPS antenna Metal sheet function and permanent damage to this product.
Installation When installing the antenna inside the vehicle (on the dashboard or rear shelf) WARNING Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as doing so may interfere with the proper functioning of such sensors or vents and may compro- mise the ability of the metal sheet under the GPS antenna to properly and securely affix to the dashboard.
Installation Attach the microphone clip to the Installing the microphone sun visor • Install the microphone in a place where its direction and distance from the driver make it easiest to pick up the driver’s Microphone clip voice. • Be sure to turn off (ACC OFF) the prod- uct before connecting the microphone.
Microphone base 2 Mount the microphone on the steering Adjusting the microphone angle column. The microphone angle can be adjusted. Double-sided tape Install the microphone on the steering column, keeping it away from the steering wheel. CAR STEREOS PIONEER AUDIO SYSTEMS...