Table of Contents
Advertisement
Installation Instructions
l“‚‹ aŒŒ o‚ŠŒ“~‰
For ease of installation, remove oven door(s) before
placing unit into cutout. This will reduce the weight of the
unit by about 35 pounds per door. Remove oven door(s)
as follows:
: Open oven door to the "Full Open" position (see
Figure 1).
: Rotate hinge locking lever DOWN, to unlock hinge
from the unit (see Figure 2).
: Close oven door to the "Removal" position (until it
stops; see Figure 3).
: Grasp the door firmly on each side and lift the door
straight up and off the unit.
klqbW q…‚ Œ“‚‹ ŒŒ † …‚~“–K _‚ ’‚ –Œ’ …~“‚ ~
ƒ†Š „† ‚ƒŒ‚ ‰†ƒ‘†‹„ ‘…‚ Œ“‚‹ ŒŒ Œƒƒ ‘…‚ ’‹†‘K
aŒ ‹Œ‘ ‰†ƒ‘ ‘…‚ ŒŒ – ‘…‚ …~‹‰‚>
A – 6
Hinge Locking Lever
(Locked Position)
c†„’‚ N
Hinge Locking Lever
(Unlocked Position)
c†„’‚ O
c†„’‚ P
16022506
l“‚‹ aŒŒ o‚‰~€‚Š‚‹‘
Replace oven door(s) after placing unit into cutout.
Replace oven door(s) as follows:
: Grasp oven door firmly on each side, hold oven door
at approximately a 30° angle and align oven door
hinge arm (see Figure 4) with hinge receiver on unit
(see Figure 5).
: Insert oven door hinge arm into hinge receiver until
the hinge arm slots (see Figure 4) align with horizontal
pins on the hinge receiver (see Figure 5) and place
hinge arm onto the hinge receiver.
: Once the hinge arms are resting on the hinge receiver
pins (see Figure 3) open oven door slowly to the "Full
Open" position (see Figure 2).
: Rotate hinge locking lever UP to the locked position to
secure the oven door to the unit (see Figure 1).
klqbW Make sure that hinge locking lever is rotated fully
UP to the locked position as shown (see Figure 1)
before closing oven door.
`^rqflk
aŒŒ ”†‰‰ ‹Œ‘ €‰Œ‚ ~‰‰ ‘…‚ ”~– ~‹ €Œ’‰ ƒ~‰‰ Œƒƒ
”…‚‹ Œ‚‹‚ †ƒ ‘…‚ …†‹„‚ ‰Œ€ˆ†‹„ ‰‚“‚ ~‚ ‹Œ‘
Œ‘~‘‚ ƒ’‰‰– rm ‘Œ ‘…‚ ‰Œ€ˆ‚ Œ†‘†Œ‹K
If hinge locking lever will not rotate fully UP to the locked
position as shown (see Figure 1) then the hinge arm is
not properly seated on the receiver. Rotate the hinge
locking lever DOWN to the unlocked position (see Figure
2) and remove oven door as outlined in the Oven Door
Removal procedure. Then replace the oven door as
outlined in the Oven Door Replacement procedure,
making sure that the hinge arm slots are fully seated on
the horizontal pins in the hinge receiver.
: Once the hinge locking lever is rotated fully UP to the
locked position (see Figure 1) close the oven door.
Hinge Arm Slots
Hinge Arm
c†„’‚ Q
Hinge Receiver
Horizontal Pins
c†„’‚ R
©2003 Maytag Appliances Company
Hide quick links:
Advertisement
Table of Contents
