Demo Mode ("A" Control) - Electrolux EIDW6105GS0 Technical & Service Manual

D D e e m m o o M M o o d d e e
F F o o r r E E l l e e c c t t r r o o l l u u x x " " A A " " C C o o n n t t r r o o l l A A c c t t i i v v a a t t i i n n g g D D e e m m o o M M o o d d e e : :
P P r r i i o o r r t t o o i i n n i i t t i i a a t t i i n n g g D D e e m m o o M M o o d d e e
1. Remove Toe and Kickplate with a #2 Phillips
screwdriver.
2. Remove cover to the junction box with a #15
Torx bit.
3. Install the provided Romex Connector in the
junction box. Connect white/white,
black/black and green/green.
4. Replace the junction box cover.
5. Connect the drain hose to the back of the unit.
Use the cork and worm clamp provided to
plug the end of the drain hose.
6. Connect power to unit.
I I n n i i t t i i a a t t i i n n g g D D e e m m o o M M o o d d e e
1. Demo mode is entered by holding the Select
Option and Right Arrow keys for 5 seconds (If
unable to access Demo menu, holding the
"SET" key for 5 seconds will reset the unit and
allow access to Demo menu).
2. The Arrow keys scrolls between Control Demo
and Sound Demo.
3. Select Control Demo by hitting the "SET" key.
4. Once in Control Demo the "SET" key will turn
ON and OFF the Control Demo.
5. Press "SET" to turn ON the Control Demo.
6. All outputs are shut off except the user inter
face, door latch and blue end-of-cycle floor
beam/indicator.
The display will flash "Control Demo" indicating
that you are in the Control Demo mode.
N N O O T T E E : : "Control Demo" refers to control demo
mode so that service technician knows to deacti-
vate the demo mode instead of replacing the con-
trol if the unit reaches a consumer's home with
demo mode activated.
7. Press and hold the Select Option and Right
Arrow keys for 5 seconds.
Welcome is displayed and control is activated to
select cycles, options, delay start, settings etc.
E E l l e e c c t t r r o o n n i i c c C C o o n n t t r r o o l l
N N O O T T E E : : The user interface selections operate as
normal. The exception is that when the user
presses the start key, there is no prompt given to
close the door. Instead the display will flash
Washing (2 seconds), Drying (2 sec) and Clean (2
sec). When Clean is displayed, the blue beam will
cycle on and remain active for 10 seconds. If the
user presses start or closes the door, then all acti-
vation resets and control returns to step 3. If delay
start is selected, then the display counts down in 1
second intervals from the delay time selected (e.g.
4 hours would be 4, 3, 2, 1 in 1 second intervals
washing, drying, clean in two
second intervals).
8. After the control demo is activated, the user
interface will default to step 3 each time the
door is opened, until the demo mode is
deactivated. If any key is pressed, the control
defaults to step 3.
9. If a power failure occurs, the unit remains in
demo mode. This prevents having to setup
all the products in a store setting after a power
failure.
10. After 10 seconds of inactivity with the door
open, the user interface becomes inactive. To
reactivate, simply press any key.
11. If the user wishes to just watch the control
demo at any time without selecting cycles,
options, etc. then the control can be activated
by pressing the start key. The start key
memory should be active to repeat the last
setting selected, and follow with the drying,
clean and blue beam.
12. Arrow to the Control DEMO ON option in the
demo menu. Press SET to turn OFF the
demo feature. Control DEMO OFF will be
displayed. At this time, all outputs are
operational.
13. To exit and return to normal operation, press
and hold Select Option and Right Arrow keys
for 5 seconds.
3-13