Table of Contents
Advertisement
L L e e v v e e l l i i n n g g a a n n d d A A n n c c h h o o r r i i n n g g D D i i s s h h w w a a s s h h e e r r W W i i t t h h i i n n
C C a a b b i i n n e e t t s s
1. Measure height of cabinet opening from under
side of countertop to floor. Check chart for
height opening and suggested adjustment.
2. Move dishwasher to front of installation area.
3. Loosen the rear leveling legs by turning
counterclockwise. Refer to chart for number of
turns.
4. Install the Cabinet Seal Kit (Instructions
included in Kit)
5.
Choose one of the methods of attachment
below to secure unit, holes need to be
pre-drilled using a #5 drill bit regardless of the
option chosen:
CAUTION
U U s s e e e e x x t t r r e e m m e e c c a a r r e e i i n n m m o o u u n n t t i i n n g g t t h h e e d d i i s s h h w w a a s s h h e e r r a a s s
t t o o n n o o t t s s c c r r a a t t c c h h , , b b u u m m p p o o r r o o t t h h e e r r w w i i s s e e d d a a m m a a g g e e t t h h e e
c c o o n n s s o o l l e e o o r r t t u u b b . .
a. Side Mount Cabinet Clips (Preferred
Method of attachment) (See Figure 2-7)
b. Top Mount Cabinet Clips (to be used when
Side Mount is not an available option)
(See Figure 2-8)
T T o o i i n n s s t t a a l l l l t t h h e e S S i i d d e e M M o o u u n n t t i i n n g g C C l l i i p p s s : :
Depending on space allowed in the cabinet, the
side mounting clips can be installed with the holes
for the screw up (preferred method) or down as
shown in the illustrations below. (Use extreme
caution when the clips are in the down position
while installing
the dishwasher).
N N O O T T E E : : Install side mount brackets before unit is
installed into the cabinet. Insert screws into the
front holes of the mounting clips only.
(See Figure 2-7)
T T o o i i n n s s t t a a l l l l u u s s i i n n g g T T o o p p M M o o u u n n t t C C a a b b i i n n e e t t C C l l i i p p s s : :
Depending on the depth of cabinet, the top mount
clips have a break off point that can be removed if
necessary.
N N O O T T E E : : Install Top Mount Clips before unit is
installed into the cabinet. Screw clips firmly to top
brace using screws provided in the literature pack.
(See Figure 2-8)
I I n n s s t t a a l l l l a a t t i i o o n n I I n n f f o o r r m m a a t t i i o o n n
Leg Leveler Adjustment Chart
Height of
Cabinet Opening
34" (86.4cm)
1
34
/
" (86.7cm)
8
34
5
/
" (87.2cm)
16
34
1
/
" (87.6cm)
2
Use if measures 34-1/8" to 35"
Screw
Use if measures 34" to 34-1/8"
Screw
F F i i g g u u r r e e 2 2 - - 7 7 . . S S i i d d e e M M o o u u n n t t C C a a b b i i n n e e t t C C l l i i p p s s
F F i i g g u u r r e e 2 2 - - 8 8 . . T T o o p p M M o o u u n n t t C C a a b b i i n n e e t t C C l l i i p p s s
2-7
Number of Turns to
Adjust Levelers
0
2
6
9
Hide quick links:
Advertisement
Table of Contents
