FUNAI HT2-M200 Owner's Manual page 47

Enable(Custom)
In following cases, select "Enable(Custom)" to set each
setting as necessary.
- When connection test failed with the setting of
"Enable(Easy)".
- When instructed by your Internet service provider to
make specific settings in accordance with your
network environment.
IP Address Setting / DNS Setting
1
Follow steps 1 to 4 in "Connection Test" on
page 46.
2
Use [K / L] to select "Enable(Custom)", then
press [ENTER].
3
Use [K / L] to select "IP Address Setting", then
press [ENTER] repeatedly to select the desired
setting.
"Auto(DHCP)" : If your router has DHCP server
function, select "Auto(DHCP)".
"Manual" : If your router does not have DHCP
server function, select "Manual".
If you select "Manual", follow the following
instruction to set the IP address and DNS.
3-a) Use [K / L] to select "IP Address", "Subnet Mask"
or "Default Gateway", then press
address setting screen will appear. Enter IP
address, subnet mask and default gateway with
cursor buttons and number buttons.
Others
IP Address Setting
IP Address
Subnet Mask
Default Gateway
then press 'ENTER'.
• Enter the IP address number after checking the
specifications of your router.
• If the IP address is unknown, check the IP
address of other devices. (e.g. PC connected via
LAN cable) and assign a different number from
those of other devices.
3-b) After you enter all correctly, press
• Confirmation message will appear. Select "Yes"
to complete the settings.
3-c) Use [K / L] to select "Primary DNS" or "Secondary
[ENTER]
DNS", then press
will appear. Enter primary DNS and secondary
DNS with cursor buttons and number buttons.
• Enter the DNS addresses provided by your
Internet provider.
• If the DNS address is unknown, check the DNS
address of other devices (e.g. PC connected via
LAN cable) and assign the same DNS address.
EN
FUNCTION SETUP
[ENTER]
. IP
xxx . xxx . xxx . xxx
xxx . xxx . xxx . xxx
xxx . xxx . xxx . xxx
[ENTER]
.
. DNS setting screen
3-d) After you enter all correctly, press
• Confirmation message will appear. Select "Yes"
to complete the settings.
4
Press [RETURN] to go back to the previous
screen, or press [SETUP] to exit.
Note
• The range of input numbers is between 0 and 255.
• If you enter a number larger than 255, the number
will automatically be 255.
• The manually entered addresses will be saved even if
you change the setting to "Auto(DHCP)".
• When you enter a wrong number, press [CLEAR] to
cancel. (The number will be back to "0".)
• If you want to enter 1 or 2 digit number in one cell,
press [B] to move on to the next cell.
• If the entered IP address or the default gateway or
primary DNS address is same as the default setting,
IP address setting will be set to "Auto(DHCP)". (The
manually entered number will be saved.)
• When IP address setting is set to "Manual", the
setting of DNS setting will automatically be "Manual"
and when IP address setting is set to "Auto(DHCP)",
you can set either "Auto(DHCP)" or "Manual" for DNS
setting.
Proxy Setting
1
Follow steps 1 to 4 in "Connection Test" on
page 46.
2
Use [K / L] to select "Enable(Custom)", then
press [ENTER].
3
Use [K / L] to select "Proxy Setting", then
press [ENTER] repeatedly to select the desired
setting.
• For default settings, select "Do Not Use".
• If you need to change the proxy setting as instructed
by your Internet service provider to set the designated
proxy address and port, select "Use".
If you select "Use", follow the following instructions
to set the proxy address and proxy port.
3-a) Use [K / L] to select "Proxy Address", then press
[ENTER]
. Proxy address setting screen will
appear. Enter proxy address.
• The keyboard screen will appear.
[K / L / 0 / 1] : Move the highlight.
[the Number buttons] : Enter number.
[ENTER] : Enter the highlighted number/word.
[RED] : Clear the entered number or word.
[GREEN] : Clear all the entered numbers or words.
[YELLOW] : Switch between abc ? ABC ? @!?
[BLUE] : Set the entered number or word.
3-b) After you enter proxy address correctly, press
[BLUE].
• Confirmation message will appear. Select "Yes"
to complete the settings.
3-c) Use [K / L] to select "Proxy Port" , then press
[ENTER]
. Proxy port setting screen will appear.
Enter proxy port number with number buttons.
3-d) After you enter proxy port correctly, press
[ENTER]
.
[ENTER]
.
47