Related Manuals for Yeti Cycles SB5C
Summary of Contents for Yeti Cycles SB5C
- Page 1 OWNER’S MANUAL YETI SB5C YETI CYCLES 600 Corporate Circle, Unit D Golden, CO 80401 888.576.9384 www.yeticycles.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS BRAND OVERVIEW FRAME FEATURES GEOMETRY MAINTENANCE SCHEDULE SETUP OVERVIEW SHOCK SETUP QUICK START GUIDE CABLE/LINE SETUP TECHNICAL ASSEMBLY OVERVIEW EXPLODED VIEWS REBUILD KITS LEGAL WARRANTY CONTACT INFORMATION... - Page 3 WELCOME TO THE TRIBE. CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI. We are confident your new bicycle will exceed This manual outlines basic setup and your expectations for value, performance, and maintenance recommendations of your new ride quality. Each frameset and component Yeti.
- Page 4 TAPERED INSET HEAD TUBE (44MM/56MM) Using our inset head tube on the SB5c allows for a larger head tube SUSPENSION BY FOX (7.875 X 2.0) with more area, increased stiffness, and lower overall ride height CUSTOM CHAIN-SLAP GUARDS without compromising any performance.
-
Page 5: Geometry
GEOMETRY FOX 34 / 140MM FORK 16.5 17.5 20.5 21.6 22.6 23.6 24.6 25.6 72.75 72.75 72.75 72.75 72.75 17.4 17.4 17.4 17.4 17.4 43.4 44.4 45.5 46.6 47.6 13.4 13.4 13.4 13.4 13.4 29.6 29.7 29.8 30.0 30.5 21.0 21.0 21.0 21.0... -
Page 6: Overview
It is important to remember that service intervals can vary specifications for individual parts on the SB5c are listed below, as well as in the step by step depending on climate, trail conditions and riding frequency. If you are unsure about working assembly instructions later in the manual. -
Page 7: Shock Setup
The main air spring controls the sag of the shock. Once you have set your baseline air pressure you For the SB5c to ride properly it is important to need to measure the sag. To measure the sag base line to get the rider started. Experiment setup the shock with the correct amount of sag. -
Page 8: Quick Start Guide
Please note this adjustment absorbency. This is the setting you will likely use only affects the shock performance while riding in the most on the SB5c. “trail” mode. QUICK START GUIDE - CTD ADJUST ADJUSTMENT... - Page 9 The staff at Yeti are sold on riding with a height adjustable seat post so we included specific cable guides for the post’s line on the SB5c. Run the line from your remote along the guides on The front derailleur housing routes down the bottom Your Internally routed dropper post housing runs the bottom of the top tube or use out internal routing option for a clean set-up.
- Page 10 The instructions denote whether to • Grease use a Loctite compound or grease. All the parts you need to assemble the SB5c. Secure your front triangle in a work stand using a • Blue (248) Loctite 30.9 seat post. Make sure you have all your tools •...
- Page 11 ASSEMBLY ASSEMBLY While holding the link in place lightly tighten the Using a well calibrated torque wrench finish Apply pink Loctite to the threads on the lower link Prep the main pivot axle with pink (222) Loctite bolts. You want them to snug so that the link tightening the Switch Infinity link bolts.
- Page 12 ASSEMBLY ASSEMBLY Using the 10mm Allen wrench, tighten the upper Using a 5mm Allen wrench, install the collet bolts Your bike comes with two cover options for the Install the internal seat post cable routing cover. link axle. Keeping the rag in place behind the into the non-drive side of the main pivot axle and internal seat post routing.
-
Page 13: Exploded View
EXPLODED VIEW GREASE LOCTITE 28 32... - Page 14 EXPLODED VIEW PARTS LIST ITEM# PART # DESCRIPTION ITEM# PART # DESCRIPTION FRONT TRIANGLE SB-5C 300030151 BOLT-TI-MALE M6X12.0MM 300070006 ICE AXE HEAD BADGE 300030154 STUD YETI TI FEMALE 8.0OD X 54.5MM, M6 300060067 YETI SEAT CLAMP QR 300030249 BOLT YETI TI FEMALE 8.0OD X 31.5MM, M6 300030069 WASHER 8.8X12.5X0.5 MM 300040443...
-
Page 15: Rebuild Kits
REBUILD KITS PART # DESCRIPTION 200020227 SB5-C HARWARE KIT 2014 300030057 BOLT CAP M6X1X20 PART # DESCRIPTION 200020226 SB5-C MASTER REBUILD KIT 300030062 WASHER SS 6.5MM ID 12.5 OD .5M 300030069 WASHER SS 8.8MM ID 12.5MM OD . 300020045 BEARING F6902 2RS 28X15X7 OUT 300030151 BOLT-TI-MALE M6X12MM 300020046... -
Page 16: Warranty
YETI Cycles shall have no liability or obligation beyond the repair or replacement of your frame Yeti Cycles will repair or replace, at its option, any of the above listed frames it determines to pursuant to the terms outlined in the warranty.