Related Manuals for Yeti Cycles SB95-C 2013
Summary of Contents for Yeti Cycles SB95-C 2013
- Page 1 OWNER’S MANUAL 2013 YETI SB 95-C YETI CYCLES 621 Corporate Circle, Unit B Golden, CO 80401 888.576.9384 www.yeticycles.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS BRAND OVERVIEW FRAME FEATURES GEOMETERY MAINTENANCE SCHEDULE SETUP OVERVIEW SHOCK SETUP CABLE/LINE SETUP TECHNICAL ASSEMBLY OVERVIEW DROPOUT SYSTEM EXPLODED VIEWS REBUILD KITS LEGAL WARRANTY CONTACT INFORMATION... - Page 3 WELCOME TO THE TRIBE. CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI. We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun.
- Page 4 THIS IS THE CULMINATION The SB95-Carbon delivers 5 inches of travel with our new Switch Technology. Efficient pedaling performance while still smooth and OF MORE THAN SIX YEARS continuous when the going gets rough. Compact, stiff, and fully sealed, the eccentric assembly is the key OF WORK AND TESTING ON component to Switch Technology and is virtually maintenance free.
-
Page 5: Geometery
GEOMETRY FOX 34 120 MM FORK 16.5 18.0 19.5 21.0 22.1 23.1 24.1 24.9 68.5 68.5 68.5 68.5 72.0 72.0 72.0 72.0 17.5 17.5 17.5 17.5 43.9 44.9 46.0 46.8 13.2 13.2 13.2 13.2 28.2 28.8 29.0 29.8 21.0 21.0 21.0 21.0 FOX 34 140 MM FORK... -
Page 6: Overview
KEEP YOUR NEW YETI FRESH AND CLEAN OVERVIEW TORQUE Following these guidelines will help maintain the performance of your bicycle and prevent Yeti strongly recommends using a torque wrench when assembling your frame. Torque more serious problems from arising. It is important to remember that service intervals can vary specifications for individual parts on the SB-95 are listed below, as well as in the step by step depending on climate, trail conditions and riding frequency. -
Page 7: Shock Setup
SHOCK SETUP YETI TIPS TOOLS NEEDED Inspect your shock for any visible damage. • Shock Pump If oil is leaking or you notice any damage to • Tape Measue the surfaces or seals, please contact the Fox Racing Shox service center for repair at 800. FOX.SHOX. - Page 8 SHOCK SETUP SHOCK SETTING NOTES: PRESSURE: MEASURED SAG (MM): REBOUND SETTING: 04. COMPRESSION DAMPING 05. TRAIL ADJUST The compression dampening has three levels The trail adjust dial controls the “trail” mode low of adjustment and is controlled by the blue speed compression adjustment.
- Page 9 CABLE SETUP YETI TIPS The SB95 Carbon uses full cable housing. This allows riders to experience better overall shifting performance by reducing the entrance of unwanted elements such as sweat and sediment. Use of full cable housing helps prevent corrosion from the elements and keeps the shifting smoother for a longer period of time.
- Page 10 Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer Lightly grease the 40mm integrated axle and Lightly grease the threads on the stop bolt and insert it through the drive side main pivot bearing.
- Page 11 ASSEMBLY ASSEMBLY Slide the upper link over the lower pivot axle Prepare a Ti male bolt with blue loctite and install Create two collet bolt assemblies. Place a collet Lightly apply pink Loctite to the collet axle sleeve on the front triangle. Ensure the Yeti logo into the threads on the drive side of the eccentric wedge over each collet bolt and secure the threads.
- Page 12 ASSEMBLY ASSEMBLY Repeat step 16 for the rear of the shock where it Tighten a collet bolt assembly into the non drive Lightly grease the shaft of the upper link collet Gently check the movement of the swingarm. It attaches to the link. side of the upper link collet axle with a 5mm allen axle.
- Page 13 12MM X 142MM DROPOUTS Axle nut and retaining hardware. This system With the rear wheel installed close the quick allows for clocking of the skewer lever for easy, release lever to the proper tension and in the consistant removal and replacement of the rear desired orientation.
-
Page 14: Exploded Views
EXPLODED VIEW 300040429 0_RING_QUAD_50P4X54X1P6 300040435 AXLE 45MM SB-95C Loctite 300040436 AXLE 40MM SB-95C Grease 300030235 BUMPER STOP RUBBER 300030234 BOLT STOP M12X1P25X10MM SB-66 40-45 in-lb [4.52-5.09 Nm] HNA00000BA00000000000 BEARING 15X24X7 3802 2RS MAX DBL ROW 300030062 WASHER 6.5X12.5X0.5 MM 300030069 WASHER 8.5X12.5X0.5 MM 300030110 BOLT-TI-MALE M6X1 12MM... -
Page 15: Rebuild Kits
200020195 SB95-C HARDWARE KIT 13 REBUILD KITS 300030062 X3 WASHER SS 6.5MM ID 12.5MM OD .5MM 300030069 X2 WASHER SS 8.5MM ID 12.5MM OD .5MM 300030110 X3 BOLT-TI-MALE M6X1 12MM 300030150 X2 BOLT-TI-FEMALE 8.0X36.5MM PART # DESCRIPTION 300030237 X1 SB-95C RETAINING RING MAIN PIVOT 200020193 SB95-C MASTER REBUILD KIT 13 300040439 X1... -
Page 16: Warranty
(applies to SB4.5c / SB5c / Beti SB5c / SB6c / ASRc / Beti ASRc) in the event of a crash or any other non-warranty situation. Yeti Cycles does this at its sole discretion and reserves the right to refuse this offer.