Panasonic AG-CPD20P Operating Instructions Manual page 114

Error Message
(continued)
No.
E1576
Write Protect Card found on slot1.
Record cannot be started.
E15764
Write Protect Card found on slot.
Record cannot be started.
E15765
Write Protect Card found on slot.
Record cannot be started.
E15766
Write Protect Card found on slot4.
Record cannot be started.
E15767
No SDHC Cards found.
Record cannot be started.
E15768
Write Error.
Record cannot be started.
E15769
Card Full.
Record cannot be started.
Recorder reboots by
E0801
unrecoverable card ejection error.
Please reinsert the card or reboot
E080
the system.
Firmware Update FAILED!
E0901
E0911 Microcontroller Update FAILED!
Unsupported Microcontroller
E091
Detected!
AG-RCP0 Update FAILED!
E091
Unsupported Control Panel
E09
Detected!
Officer's information file cannot be
E40
loaded.
Since you are not an
E41
administrator, you cannot open
this menu.
Officer's information file cannot be
E4
loaded.
Admin's information file cannot be
E4
loaded.
E45 Classification list cannot be
loaded.
Message
The write-protection switch on the SDHC Memory Card is set to the "LOCK"
position. Slide the write-protection switch away from the "LOCK" position.
No SDHC Memory Card is inserted. Insert an SDHC Memory Card.
The SDHC Memory Card cannot be written to. Replace the SDHC Memory
Card.
The following conditions may have occurred.
• There is no space left on the SDHC Memory Card.
• Files contained in one of the SDHC Memory Cards inserted in the SDHC
Memory Card slots 1, 2, 3, and 4 exceed 5,000 files.
Replace the SDHC Memory Card with an SDHC Memory Card with free
capacity, or free up space in the SDHC Memory Card for new data. (free
space of more than 10 MB)
Be sure to use the correct procedure to remove and load SDHC Memory
Cards.
Check the SDHC Memory Card and re-insert it, or reboot the recorder.
An error occurred during the update.
• Check whether the update file for the recorder has been correctly copied
to the SDHC Memory Card or USB memory device.
• Reformat the SDHC Memory Card or USB memory device before use.
• Use another USB memory device.
• Check whether there are multiple update files on the SDHC Memory Card
or USB memory device.
• Check whether there are multiple SDHC Memory Cards and/or USB
memory devices containing update files.
• An SDHC Memory Card with a \DATA folder cannot be used for updating.
• A USB memory device containing a folder other than the \WIDKEY folder
cannot be used for updating.
An error occurred during the update.
The recorder reboots automatically to restart an update.
Contact your supplier if the problem persists.
The recorder has broken down.
Contact your supplier.
An error occurred during an update of an AG-RCP0 connected to the
recorder.
The recorder reboots automatically to restart an update.
Contact your supplier if the problem persists.
A Remote Control Panel not supported by the recorder was detected.
Disconnect the Remote Control Panel.
The officer data file (WID
save it to a USB memory device and re-register it.
You are not registered as an administrator and cannot open this menu. Ask a
registered administrator for assistance.
There is no Officer Registration file or it contains the wrong data. Create a
correct Officer Registration file (WOFFICER.TXT), copy it to a USB memory
device and reload it.
There is no Administrator Registration file or it contains the wrong data. Create
a correct Administrator Registration file (WADMIN.TXT), copy it to a USB
memory device and reload it.
There is no classify file or the content of the file is incorrect. Copy the
correct classify file (CLASSIFY.TXT) to the USB memory device and
reregister it.
Measure
.TXT) is corrupted. Create a new officer's data file,
*****
114