Advertisement
Page 6
SB-2-601-C
TROUBLESHOOTING (continued)
CONDITION
Fluid leaking from packing nut
Fluid leaking or dripping from
front of gun
Runs and sags
Thin, sandy coarse finish
drying before it flows out
Thick, dimpled finish "orange
peel".
ACCESSORIES
TGC-545 Aluminum
PTFE
TLC-555 (PTFE Lined)
Drip Free Suction Cups
Cups have a unique, two
position valve which permits
selection of either a drip free or
conventional open vent mode.
®
Scrubs
Hand Cleaner Towels
192218 (
Automotive Refinish)
29-3100 (
Industrial Finishing)
Scrubs® are a pre-moistened
hand cleaner towel for paint-
ers. No water is needed.
WR-103 Wrench
Contains all necessary tip,
hose and nut sizes used on or
with gun.
HAF-507 Whirlwind™
In-Line Air Filter
Removes water, oil, and
debris from the air line.
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited Warranty.
DeVilbiss Worldwide Sales and Service Listing: www.devilbiss.com
Industrial Finishing
DeVilbiss has authorized distributors throughout the world. For
technical assistance or the distributor nearest you, see listing below.
U.S./Canada Technical Service Office:
195 Internationale Blvd., Glendale Heights, IL 60139
Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-368-8401
CAUSE
Packing nut loose.
Packing worn or dry.
Packing nut too tight.
Dry packing.
Fluid tip or needle worn or damaged.
Foreign matter in tip.
Fluid needle spring broken.
Wrong size needle or tip.
Too much material flow.
Material to thin.
Gun tilted on an angle or gun motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Too much material coarsely atomized.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
192212
Professional Spray
Gun Cleaning Kit
Contains 6 precision
tools to effectively
clean DeVilbiss, Binks,
Finishline and other
brand spray guns
MSP-524 Twin Cartridge,
Paint Spray Respirator
NIOSH-Certified
(TC-84A-1623) for respira-
tory protection in atmos-
pheres not immediately
dangerous to life.
CORRECTION
Tighten, do not bind needle.
Replace or lubricate.
Adjust
Lubricate.
Replace tip & needle.
Clean.
Replace.
Replace.
Adjust gun or reduce fluid pressure.
Mix properly or apply light coats.
Hold gun at right angle to work and adapt to
proper gun technique
Check distance. Normally 6-8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instructions.
Check distance. Normally 6-8".
Turn in fluid adjusting screw or reduce fluid
pressure or change to a smaller tip size.
Increase air pressure or reduce fluid pressure.
Follow paint manufacturer's mixing instructions.
Follow paint manufacturer's mixing instructions.
Properly clean and prepare.
Spray Gun Lube
HAV-500 OR
SSL-10
HAV-501
(2 oz. bottle)
Adjusting Valve
(HAV-501 SHOWN)
Compatible with all
paint materials; con-
tains no silicone or
petroleum distillates
HAV-500 does not have
to contaminate paint.
pressure gauge. Use to
MSDS available upon
control air usage at gun.
request.
FLG-463
Air Cap Test Kit
(#3 Air Cap)
The purpose of this
test kit is to measure
air cap atomizing air
pressure
at
the
center air port of the
air cap.
Used to
confirm
code
compliance and as a
daily quality control
measure.
Automotive Refinishing
DeVilbiss has authorized distributors throughout the world.
For equipment, parts and service, check the Yellow Pages
under "Automotive Body Shop Equipment and Supplies."
For technical assistance, see listing below.
U.S./Canada Customer Service Office:
1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537
Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-445-6643
5/04 ©2004
Automotive Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4719
Coupler
HC-4419 Stem
1/4" NPT(M) /
1/4" NPT(F)
NPS(M)
HC-1166 Stem
HC-4720 Coupler
1/4" NPT(M)
1/4" NPT(F)
Industrial Quick Connects
Approved for HVLP Guns (Air)
High Flow Ball and Ring Type
HC-4419 1/4"
HC-4699
NPS(F)
1/4" NPT(M)
HC-4700
HC-1166
1/4" NPT(F)
1/4" NPT(M)
Inc. All rights reserved. Printed in U.S.A.
Advertisement
