DeVilbiss FinishLine FLG-611-114 Operation Manuals

Conventional and hvlp gravity feed spray gun and cup outfits. finishline flg-611 series; finishline flg-631 series
Hide thumbs

Advertisement

Quick Links

CONVENTIONAL AND HVLP GRAVITY FEED
SPRAY GUN AND CUP OUTFITS
Read and follow all instructions and SAFETY PRECAUTIONS
DESCRIPTION
The FLG-611 and FLG-631 are lightweight, general purpose spray guns for both conventional and HVLP spraying applications
suitable for use with a wide variety of common coating materials.
The No.1 (conventional) air cap on the FLG-611 requires an air supply at gun inlet of approximately 45 psi and can be
operated from a 3 hp compressor. The No.2 (conventional) air cap on the FLG-611 requires an air supply at the gun of
approximately 40 psi and can be operated from a 1-1/2 - 2 hp compressor. The No.3 (HVLP) air cap on the FLG-631 requires
a maximum of 23 psi gun inlet pressure, and can be operated from a 3 hp air compressor.
Products shown here are covered by US patent number 5,803,367.
IMPORTANT: These guns may be used with most common coating and finishing materials. They are designed for use with
mildly corrosive or non abrasive materials. If used with other high corrosive or abrasive materials, it must be expected that
frequent and thorough cleaning will be required and the necessity for replacement of parts will be increased.
MODELS
FLG-611
Conventional Gravity Feed Gun and Cup Outfit
FLG-631
HVLP Gravity Feed Gun and Cup Outfit

SPECIFICATIONS

Maximum recommended working pressure: 100 psi
Air inlet threads
Materials in contact with coating materials
Fluid tip material
Fluid inlet threads
Fluid needle
HVLP models
Operation Manual:
Important:
before using this equipment
1
:
¼
" NPS(M)
4
: Polyarylamide
: Stainless steel.
: Stainless steel.
: 23 psi air inlet pressure (with trigger pulled) delivers 10 psi air cap pressure
SB-US-2- 579-C

Advertisement

loading

  Related Manuals for DeVilbiss FinishLine FLG-611-114

  Summary of Contents for DeVilbiss FinishLine FLG-611-114

  • Page 1: Specifications

    SB-US-2- 579-C Operation Manual: CONVENTIONAL AND HVLP GRAVITY FEED SPRAY GUN AND CUP OUTFITS Important: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment DESCRIPTION The FLG-611 and FLG-631 are lightweight, general purpose spray guns for both conventional and HVLP spraying applications suitable for use with a wide variety of common coating materials.
  • Page 3 SPRAY GUN SPRAY GUN NO. ON REFERENCE #2 REFERENCE #3 FLUID REFERENCE #6 AIR CAP COMPUTER MODEL AIR CAP AIR CAP FLUID TIP FLUID NEEDLE TIP, NEEDLE NUMBER NUMBER PART PART SIZE PART NUMBER NUMBER (MM) NUMBER 512114 FLG-611-114 519001(FLG-1-1K) 519014 (FLG-2-14K) 1.4(STD) 519114(FLG-401-14K) 519174(FLG-451-14)
  • Page 4: Installation

    Lubrication Oil daily, the air valve stem where it enters the gun body and the needle (6) where it enters the screw (8). DeVilbiss spray gun lube (SSL-10) is recommended for spray gun lubrication. REPLACEMENT OF PARTS NOTE: The air and coating material connectors are not removable.
  • Page 5: Safety Warnings

    SAFETY WARNINGS FIRE AND EXPLOSION Solvents and coating materials can be highly flammable or combustible, especially when sprayed. • Work stations must be provided with adequate ventilation/exhaust to prevent the build-up of flammable vapours. • Smoking and naked flames must not be allowed in the spraying or mixing areas. •...
  • Page 6: Service Checks

    ACCESSORIES Gravity Feed Gun Hook: Order GFG-6 - A handy wall mounted bracket to hang up your gravity feed spray guns. SERVICE CHECKS NORMAL SPRAY PATTERN Fluid leakage from packing nut Will not spray CONDITION CAUSE CORRECTION 1. No pressure at the gun. 1.
  • Page 7 EZ LINERS ASSEMBLY Liner Hold liner Piercing Drain stretches around bushing to make a leak- proof seal Piercing/assembly Drain ) Remove protective cap from piercing/assembly tool tip. Place drain bushing on tool. (2) Install tool with bushing into the liner and pierce a hole in the bottom, centre of liner. (3) Firmly push the bushing and liner into the drain hole in the paint cup bottom.
  • Page 8 Hold tube brush here when installing into Waste paint Drain Straighten brush before (4) Properly dispose of remaining paint in paint liner. Open zipper to allow for quicker draining of paint. Dispose of used liner and bushing – DO NOT REUSE. (5) Pour a small amount of clean paint solvent into paint cup.

This manual is also suitable for:

Finishline flg-611-212Finishline flg-611-318