Advertisement
Page 6
SB-2-511-A
TROUBLESHOOTING (continued)
CONDITION
Fluid dripping or leaking from
bottom of cup
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange peel"
ACCESSORIES
SRI-5033-215 Air Cap Test Kit
The purpose of this test kit is
to measure air cap pressures.
Used to confirm code com-
pliance and as a daily quality
control measure.
Automotive Refinish Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4419 Stem
HC-4719 Coupler
1/4" NPT(F)
1/4" NPT(M) /NPS(M)
HC-1166 Stem
HC-4720 Coupler
1/4" NPT(M)
1/4" NPT(F)
192219 Gun Holder, Coated
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited Warranty.
DeVilbiss Worldwide Sales and Service Listing: www.devilbiss.com
DeVilbiss Automotive Refinishing
DeVilbiss has authorized distributors throughout the world.
For equipment, parts and service, check the Yellow Pages
under "Automotive Body Shop Equipment and Supplies."
For technical assistance, see listing at right.
CAUSE
Cup loose on gun.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun
motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
MSP-524
Twin Cartridge, Paint Spray
NIOSH-Certified (TC84A-1623)
for respiratory protection in
atmospheres not immediately
dangerous to life.
HAV-500 OR
HAV-501
Adjusting Valve
(HAV-501 SHOWN)
HAV-500 does not
have pressure gauge.
Use to control air
usage at gun.
192212 Professional
Spray Gun Cleaning Kit
Contains six precision tools
designed to efffectively clean
all DeVilbiss, Binks, Finishline
and other brand products.
U.S./Canada Customer Service Office:
1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537
Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-445-6643
CORRECTION
Tighten.
Clean
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and
adapt to proper gun technique.
Check distance. Normally approx. 3-6".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instrs.
Check distance. Normally approx. 3-6".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instrs.
Properly clean and prepare.
54-4350 Gun Holder
Consists of: 2 brushes,
1 wire pick. Helps keep
Designed to hold gravity
air cap clean and per-
feed guns and cups. Also
holds paint strainers.
forming properly.
®
192218 Scrubs
Hand Cleaner Towels
Scrubs® are a premoistened hand
cleaner towel for painters, body
men and mechanics that go where
you go and no water is needed.
10/04 ©2004
KK-5060 Air Cap
HAF-507
Cleaning Kit
Whirlwind™
In-Line Air Filter
Removes water, oil,
and debris from the
air line.
Spray Gun Lube
SSL-10 (2 oz. bottle)
Compatible with all paint materials;
contains no silicone or petroleum
distillates to contaminate paint.
MSDS Sheet available upon request.
All rights reserved. Printed in U.S.A.
Advertisement
