Table of Contents
Advertisement
Page 6
SB-2-168-K
TROUBLESHOOTING (continued)
CONDITION
Fluid dripping or leaking from
bottom of cup
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange peel"
ACCESSORIES
GFC-501 (Acetal) 20 Oz. Cup
GFC-502 (Aluminum) 1 Liter Cup
Gravity Feed Cups
These gravity feed cups
are designed to be used
with FLG, GFG, GFHV or
GTI gravity feed spray guns.
GTI-5033-2000
Air Cap Test Kit
The purpose of this test kit
is to measure air cap
atomizing air pressure at
the center air port of the air
cap. Used to confirm code
compliance and as a daily
quality control measure.
Automotive Refinish Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4419 Stem
HC-4719 Coupler
1/4" NPT(F)
1/4" NPT(M) /NPS(M)
HC-1166 Stem
HC-4720 Coupler
1/4" NPT(M)
1/4" NPT(F)
WR-103 Wrench
Contains all necessary
tip, hose and nut sizes
used on or with gun.
DeVilbiss Worldwide Sales and
Service Listing: www.devilbiss.com
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited
Warranty.
CAUSE
Cup loose on gun.
Cup gasket worn or missing below cup.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun
motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
HAV-500 OR
192212 Professional
HAV-511
Cleaning Kit
Adjusting Valve
(HAV-511 SHOWN)
Contains six preci-
sion tools designed
HAV-500 does not
to effectively clean
have pressure gauge.
all DeVilbiss, Binks,
Use to control air
Finishline and other
usage at gun.
brand spray guns.
MSP-524
Twin Cartridge,
Paint Spray
Respirator
NIOSH-Certified
(TC84A-1623) for respira-
tory protection in atmos-
pheres not immediately
dangerous to life.
HAF-507 Whirlwind™
In-Line Air Filter
Removes water, oil,
and debris from the
air line.
ITW Automotive Refinishing
DeVilbiss has authorized distributors throughout the world.
For equipment, parts and service, check the Yellow Pages
under "Automotive Body Shop Equipment and Supplies."
For technical assistance, see listing below.
U.S./Canada Customer Service Office:
1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537
Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-445-6643
5/04 ©2004 Illinois Tool Works Inc. All rights reserved. Printed in U.S.A.
CORRECTION
Tighten.
Replace cup gasket.
Clean.
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and
adapt to proper gun technique.
Check distance. Normally approx. 8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instrs.
Check distance. Normally approx. 8".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instrs.
Properly clean and prepare.
JGA-156-K10
Spring Clips
Spray Gun
Joins any single
piece DeVilbiss air
cap
with
version MBC-368,
MSA-1 or GTI-3
retaining
Helps prevent parts
loss and provides
easier assembly.
GH-505 Gun
Holder
Gun Holder
Gun holders are
Gun holder made to
made to hold stan-
hold
dard paint cups, grav-
gravity cups.
ity feed guns and
cups, and paint filters.
OMX-70-K48 Paint Cup Liner Kit
Allows quick and
easy clean-up, and
also allows spraying
with the gun point-
ing upward.
192218 Scrubs
®
Hand Cleaner Towels
latest
®
Scrubs
are
a
moistened hand cleaner
rings.
towel for painters, body
men and mechanics that
go where you go and no
water is needed.
Spray Gun Lube
192219
SSL-10 (2 oz. bottle)
Compatible with all
paint materials;
contains no silicone
or petroleum distil-
lates to contami-
guns
with
nate paint. MSDS
Sheet
available
upon request.
Consists of :
1 - Piercing Tool
48 - Disposable Liners
48 - Drain Bushings
pre-
Advertisement
Table of Contents
