Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fire Sense 61280
Summary of Contents for Fire Sense 61280
-
Page 2: Table Of Contents
Contents DANGER General Safety Information........DANGER indicates an imminently hazardous situation Assembly Instructions……………………………….. which, if not avoided, will result in death or serious injury. Components & Hardware........Additional Requirements........Installation Process…………………………………... WARNING Step1 - Attach Wheel Assembly to Base....Step 2 – Attach Sand Box to Base......WARNING indicates an imminently hazardous situation which, if not avoided, could result in death or serious injury. - Page 3 DANGER DANGER • EXPLOSION - FIRE HAZARD • CARBON MONOXIDE HAZARD • Keep solid combustibles, such as building materials, • This heater is a combustion appliance. All combustion paper or cardboard, a safe distance away from the heater appliances produce carbon monoxide (CO) during the as recommended by the instructions.
-
Page 5: Additional Requirements
Hardware Picture Description Used in Step(s) M6x12 Hex Bolt Installation process Assembly time: 40 minutes M6 Flange Nut M6x10 Round Head Screw M5 Flange Nut tep 1 – Attach Wheel Assembly to Base Line up holes in Wheel Bracket with corresponding M6 Cap Nut holes in Base and insert 2 - M 8 x 1 2 B o l t s through holes. -
Page 6: Step 3 -Attach L-Shaped Brackets To Base
For models without table, skip to Step 6. Insert Sand Box inside Base and screw on M8 nut. Step 5 – Table Installation Tighten with Philips screwdriver. Slide part 4 over Post and down onto Cylinder Housing. Slide Part 3 down over post and onto Part 4. -
Page 7: Step 7 - Attach Head Assembly To Post
Step 7 – Attach Head Assembly to Post Unscrew 4 Small Bolts and 4 Lock Washers pre-assembled in Head Assembly. 4 Small Bolts 4 Lock Washers Load Head Assembly by inserting hose into post. Insert Head Assembly into post. 9 M6x10 Flat Head Screws 9 M6 Cap Nuts Control knob should be above decal on post. -
Page 8: Step 9 - Attach Reflector Assembly To Studs
tep 9 – Attach Reflector Assembly to Studs The minimum permissible gas supply pressure of 10 W.C. is required for purpose of input adjustment. Support Heater. Slide 3 M 8 Flat Washers over threaded end The minimum hourly of 17000 BTU is required Reflector Studs. -
Page 9: Leak Check
Leak Check Operation WARNING DANGER • Perform all leak tests outdoors. • Extinguish all open flames. • CARBON MONOXIDE HAZARD • NEVER leak test when smoking. • For outdoor use only. Never use inside a house or any • Do not use the heater until all connections have been leak other unventilated or enclosed areas. - Page 10 Push and release the igniter button on the control Before Turning Gas Supply ON: panel until flame is visible through Viewing Hole. Release Control Knob after 30-60 seconds. Pilot Your heater was designed and approved for outdoor Light will remain lit. If not, return to step 1. use only.
-
Page 11: Operation Checklist
Shut Down: experience ignition problems please consult “Troubleshooting” on page 11. Turn Control Knob clockwise to Pilot. (Normally, burner will make a slight popping sound when Caution: Avoid inhaling fumes emitted from the extinguished.) Burner will extinguish but Pilot will heater’s first use. -
Page 12: Troubleshooting
Troubleshooting If the problem is: And this condition exists: Then do this Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control Pilot won’t light Air in gas line knob in) for not more than 1 - 2 minutes or until you smell gas... -
Page 13: Storage
Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. hail, snow, dust and debris). Heater glow is excessively uneven. If desired, cover heater to protect exterior surfaces Heater makes popping noises. - Page 14 Customer Service Hours: Mon. – Fri. 9:00 a.m. – 6:00 p.m. (EST) Fire Sense®, Mojave Sun ®, and Well Traveled Living® are registered trademarks of Well Traveled Imports, Inc®. All assembly instruction presentations are the property of Well Traveled Imports, Inc.® and are protected by U.S. copyrights and trademarks. All rights reserved.