Subscribe to Our Youtube Channel
Related Manuals for Perle IDS-105G
Summary of Contents for Perle IDS-105G
-
Page 1: Installation Guide
Perle IDS-105G (XT) Unmanaged 10/100/1000 Ethernet Switches Installation Guide P/N 5500340-10 (Rev D) - Page 2 The SFP transceiver ports support SFP’s supplied by Perle, Cisco or other manufacturers of MSA complaint SFP modules. Visit the Perle website for the most up to date installation guides, models and specifications. http://www.perle.com/...
- Page 3 Industrial temperature models • DIN-rail or wall/panel mounting Note – In this guide the various models will be referred to as the IDS-105G Getting to know your IDS-105G Switch Package Contents: • IDS-105G • DIN-rail mounting clip (pre-installed on the unit) •...
- Page 4 Front View of IDS-105G (5 port RJ-45) - 4 - IDS-105G Installation Guide...
- Page 5 Front View of IDS-105G (with two SFP transceiver ports) IDS-105G Installation Guide - 5 -...
- Page 6 Front View of IDS-105G (with one fiber port) - 6 - IDS-105G Installation Guide...
-
Page 7: Reset Button
Reset Button To reset the IDS-105G insert a paper clip into the air hole vent and gently press the reset button. The LEDs on the IDS-105G will go On and then momentarily Off when released to show that the unit has been reset. -
Page 8: Led Status
Port Link / Speed (Green and Yellow LEDs) On: Link up 1000 Mbps: Green On; Yellow Off 100 Mbps: Green On; Yellow On 10 Mbps: Green Off; Yellow On Flashing: Link up and Ethernet activity detected Off: Link Down - 8 - IDS-105G Installation Guide... - Page 9 Views for the IDS-105G Note: all dimensions are in mm IDS-105G Installation Guide - 9 -...
- Page 10 - 10 - IDS-105G Installation Guide...
- Page 11 1. The DIN-rail clip will be fixed to the back panel of the IDS- 105G switch when you receive the product. 2. Position the IDS-105G switch such that the top of the DIN-rail fits into the slot on the top of the DIN-rail clip, just below the hook and behind the spring.
- Page 12 6. Pull the IDS down to lock the IDS-105G to the wall mount. 7. Tighten the four screws securely to the wall. Note: For the best results use screws that have the following attributes: Head diameter .5 - .6 mm...
-
Page 13: Hazardous Location Warnings
Power sources must be off prior to beginning the power connection steps. Ensure that the voltage and current ratings of the intended power source are appropriate for the IDS-105G as indicated on the product label. Ensure that the installation and electrical wiring of the equipment is... - Page 14 Connecting the IDS-105G to ground If your installation requires additional grounding follow this procedure. 1. Follow the manufacturer’s instructions for attaching the ground wire to grounding lug. 2. Attach the grounding lug to the chassis and secure with the grounding screw provided.
- Page 15 50/125 microns or 62.5/125 microns 9/125 microns Connect the fiber cables to Port 6/7 on the IDS-105G and the other end to a compliant fiber devices. If you are making your own fiber cables, remember that the RX on one side needs to go to TX on the other side and vice versa.
-
Page 16: Technical Specifications
Port 6 – port status (Fiber or SFP models) Port 7 – port status (SFP models) Environmental Operating Temperature Commercial Models 0°C to 60°C (32°F to 140°F) IDS-105G-(D)SFP and IDS-105G-xxxxxxxx Industrial Models -40°C to 75°C (-40°F to 167°F) IDS-105G-(D)SFP-XT and IDS-105G-xxxxxxxx-XT Storage Temperature Commercial Models -25°C to 70°C (-13°F to 158°F) -
Page 17: Fiber Specifications
6.2 miles RX:1310 Max:-3 Max:-3 20 km TX: 1310 Min:-8 Min:-22 IDS-105G-S1SC20U None duplex 12.4 miles RX1490 Max:-3 Max:-3 20 km TX: 1490 Min:-8 Min:-22 IDS-105G-S1SC20D None duplex 12.4 miles RX:1310 Max:-3 Max:-3 IDS-105G Installation Guide - 17 -... - Page 18 TX: 1550 Min:0 Min:-32 IDS-105G-S2SC160 None duplex 100 miles RX:1550 Max:5 Max:-9 160 km TX: 1550 Min:0 Min:-32 IDS-105G-S2ST160 None duplex 100 miles RX:1550 Max:5 Max:-9 * fiber characteristics are determined by the SFP inserted - 18 - IDS-105G Installation Guide...
-
Page 19: Contacting Technical Support
This product is covered by the Perle Ethernet Switches Warranty. Details can be found at: http://www.perle.com/support_services/warranty.shtml Copyright © 2014 Perle Systems Limited all rights reserved. No part of this document may be reproduced or used in any form without written permission from Perle Systems Limited.
Need help?
Do you have a question about the IDS-105G and is the answer not in the manual?
Questions and answers