Subscribe to Our Youtube Channel
Related Manuals for Perle 07013050
Summary of Contents for Perle 07013050
- Page 1 IDS-305G Hardware Installation Guide Managed Industrial Ethernet Switches Updated: September 2016 Revision 1.00 www.perle.com Document Part#: 5500401-10...
-
Page 2: Table Of Contents
Table of Contents Preface ......................2 Overview . - Page 3 Modifications to this product not authorized by Perle could void the FCC approval and negate your authority to operate the product. Perle reserves the right to make changes without further notice, to any products to improve reliability, function, or design.
-
Page 4: Preface
This document describes the hardware and physical characteristics of the Perle IDS switch. It covers hardware features as well as installation and operation of the switch. This document does not cover how to configure your Perle IDS switch. Information to configure your Perle IDS switch can be found in the Perle IDS User’s Guide Package Contents •... -
Page 5: Overview
10/100/1000Base-T (RJ45) 1000Base-X SC/ST fiber Standard IDS-305G-XXXXXX-XT 10/100/1000Base-T (RJ45) 1000Base-X SC/ST fiber Industrial Note: xxxxxx denotes the specific type of fiber port installed. Refer to the Perle Website for up to date details on the available options. IDS-305G Hardware Installation Guide... -
Page 6: Switch Model View
Switch Model View IDS-305G Note: Fiber Port may appear different, depending on the type of fiber port installed. IDS-305G Hardware Installation Guide... -
Page 7: Led Indicators
LED Indicators P (Power Inputs) State Description Green P1 and P2 Power inputs within specifications Yellow P1 or P2 Providing power within specifications Neither P1 or P2 providing power within specifications Sys (System Status) State Description Green - blinking (after power on) System booting Green - solid System ready/operating normally... - Page 8 LED Indicators 6 RM (Ring Master) State Description Ring Master not activated Green - solid Ring Master Active, redundant port blocked. Coupling Link enabled Green - flashing Ring Master unable to establish a ring due to missing link on one of the Ring ports Yellow - solid Ring Master Active, redundant port unblocked - indicates a break in the Ring...
-
Page 9: Ports
These ports provide a built in fiber module that provides fiber connectivity at 100 Mb/s. These fiber ports are available on the switches in a variety of distances, wavelengths and connector types. Consult the full model list at www.perle.com. Power Connector The power input connector has provisions for dual inputs. -
Page 10: Port Status Indicators
Port Status Indicators Ethernet Port Status Indicators Port Link / Speed (Green and Yellow LEDs) State Description Green 1000 Mbps Green / Yellow 100 Mbps Yellow 10 Mbps On solid Port Link Random blinking Port Link and Activity Slow blinking Error disabled Rapid blinking Port in Fast Setup Mode... -
Page 11: Installation
Installation This chapter discusses the following topics: • Cautions and Warnings • Terminal Block-Power Connectors • Grounding the IDS Switch • Connecting Power to the IDS Switch • Wiring the Relay Alarm • Connecting the Console Port • RJ45 Console Port •... -
Page 12: Terminal Block-Power Connectors
Warning: In case of malfunction or damage, no attempts at repair should be made. Do not dismantle the product. All repairs need to be made by a qualified Perle representative. Warning: Explosion hazard. Do not remove or replace lamps, fuses or plug-in modules (as applicable) unless power has been disconnected or the area is free of ignitable concentrations. -
Page 13: Connecting The Console Port
Installation 11 Connecting Power to the IDS Switch The IDS switch has two power inputs that can be connected simultaneously to provide redundant power. If one power source fails the other source acts as a backup, and automatically powers the switch. Conductors suitable for use in an ambient temperature of 98 C must be used for the Power Supply Ter- minals. -
Page 14: Connecting Destination Ports
Installation 12 3 Click the Hardware tab and choose Device Manager, Expand the Ports(COM & LPT) section. This will expand the drop down to show the number of com ports on your system. Connect the cable to one of these ports (probably com1 or com2). 4 Start an terminal-emulation program (such as Putty or SecureCRT ) on the COM port where you have connected the cable PC. -
Page 15: Resetting The Switch
Installation 13 Resetting the Switch The Reset/Fast Setup button is located near the bottom of the switch. A small tool such as a paper clip is needed to access the recessed button. Soft Reset To reset/restart the switch you can perform a soft reset. Press and immediately release the reset button to perform a soft reset. -
Page 16: Booting The Switch
Installation 14 Booting the Switch When first applying power to the IDS switch, it will startup and go through the boot process. The LEDs will behave according to the table below. Behavior Yellow during the booting process. Once the system software has been loaded, the PWR LED will reflect the status of the power inputs. -
Page 17: Configuring The Ids Switch
Command Line Reference Guide for more information. Web Device Manager The Perle Web Device Manager is an embedded Web based application that provides an easy to use browser interface for managing the switch. This interface provides the ability to configure and manage the switch. -
Page 18: Appendix A - Technical Specifications
Appendix A - Technical Specifications This appendix provides the technical specification for the IDS-305G(-XT ) switches. Specifications Dual input terminal block 9.6 to 60 VDC SELV, limited-energy per 61010-1 cl.9.4 Models Rated Voltage Max. Rated Alarm Relay Output (CLASS 2) Current IDS - 205G(-XT) 9.6 Vdc... - Page 19 60°C (140°F). However, the IDS switch can function in the environmental conditions listed above. Contacting Technical Support Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. A Technical Support Query may be made via this webpage. www.perle.com/support_services/support_request.shtml Warranty / Registration This product is covered by the Perle Ethernet Switches Warranty.
-
Page 20: Appendix B - Labels
Appendix B - Labels IDS-305G IDS-305G-XT IDS-305G Hardware Installation Guide... -
Page 21: Appendix C - Mechanical Drawings
Appendix C - Mechanical Drawings 5-port RJ-45 IDS-305G Hardware Installation Guide... -
Page 22: Appendix D - Ids Din Rail And Wall Mounting
Appendix D - IDS DIN Rail and Wall Mounting This appendix provides instruction on the following: • Mounting the IDS Switch on a DIN Rail • Removing the IDS from the DIN Rail • Wall Mounting the IDS Mounting the IDS Switch on a DIN Rail 1 The DIN rail clip will be fixed to the back of the IDS unit when you receive the switch. - Page 23 Appendix D - IDS DIN Rail and Wall Mounting 21 3 Use the wall mount plates as a guide to mark the spot where the screws will be placed. 4 Drive the screws into the wall leaving about 2 mm of the screw protruding from the wall to allow room for sliding the wall mount panel between the wall and the screws.
-
Page 24: Appendix E - Ids Maintenance
Appendix E - IDS Maintenance • Ensure there is clearance of 50.8mm (2 inches) on all sides of the IDS switch to provide proper airflow through the unit • Do not use solvents or cleaning agents on this unit • Keep vent holes clear of debris •... -
Page 25: Appendix F - Cables And Connectors
- 0.33mm • Straight through or Ethernet Crossover cable Note: An optional cable adapter is available to provide RJ45 to DB9 conversion: Perle’s optional RJ45 to DB9-F crossover adapter model DB0020C enables a straight through Ethernet cable to connect the RJ45 console port to a PC serial port. - Page 26 Appendix F - Cables and Connectors 24 Ethnernet Connector - 8-pin RJ-45 Fiber Port Cabling Requirements Duplex SC or ST Connector • Multimode 50/125 or 62.5/125 micron fiber cable • Single mode 9/125 micron fiber cable Simplex (BIDI, single strand) SC or ST connector •...
Need help?
Do you have a question about the 07013050 and is the answer not in the manual?
Questions and answers