Subscribe to Our Youtube Channel
Related Manuals for Perle IDS-108F
Summary of Contents for Perle IDS-108F
-
Page 1: Installation Guide
Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches Installation Guide P/N 5500339-10 (Rev E) - Page 2 Auto-negotiation on copper ports • Redundant DC power inputs • Rugged high-strength case • Industrial temperature models • Din-rail or wall/panel mounting Note – In this guide the various models will be referred to as the IDS-108F - 2 - IDS-108F Installation Guide...
- Page 3 Package Contents: • IDS-108F • DIN-rail mounting clip (pre-installed on the unit) • This guide Note – Optional panel/wall mounting kits may be ordered for the IDS-108F Front View of IDS-108F (8 port RJ-45) IDS-108F installation Guide - 3 -...
- Page 4 Front View of IDS-108F (with two Fiber ports) - 4 - IDS-108F Installation Guide...
-
Page 5: Specifications
12 AWG (0.0804-3.31 mm2), torque value 4.5 lb-in. Power The IDS-108F switch has two power inputs that can be connected simultaneously to DC or AC power sources. If one power source fails, the other acts as a backup, and automatically powers the switch. -
Page 6: Reset Button
Reset Button To reset the IDS-108F insert a paper clip into the air hole vent and gently press the reset button. The LEDs on the IDS-108F will go On and then momentarily Off when released to show that the unit has been reset. - Page 7 Dimensions for the IDS-108F IDS-108F installation Guide - 7 -...
- Page 8 - 8 - IDS-108F Installation Guide...
- Page 9 1. The DIN-rail clip will be fixed to the back panel of the IDS- 108F switch when you receive the product. 2. Position the IDS-108F such that the top of the DIN rail fits into the slot on the top of the DIN-rail clip, just below the DIN-rail hook and behind the spring.
- Page 10 6. Pull the IDS down to lock the IDS-108F to the wall mount. 7. Tighten the four screws securely to the wall. Note: For the best results use screws that have the following attributes: Head diameter .5 - .6 mm...
- Page 11 Power sources must be off prior to beginning the power connection steps. Ensure that the voltage and current ratings of the intended power source are appropriate for the IDS-108F as indicated on the product label. Ensure that the installation and electrical wiring of the equipment is...
- Page 12 If your installation requires additional grounding follow this procedure. 1. Select and obtain an appropriate grounding lug that can be affixed to the ground screw on the top of the IDS-108F. 2. Follow the grounding lug manufacturer’s instructions for attaching it to the ground wire.
- Page 13 9/125 microns Connect the fiber cable to Port 9 and Port 10 (if installed) on the IDS-108F and the other end to a compliant fiber device. If you are making your own fiber cables, remember that the RX on one side needs to go to TX on the other side and vice versa.
-
Page 14: Technical Specifications
P1 – power 1, P2 – power 2 Ports 1 – 8 G/Y – Link/Activity/Speed Port 9 /10 – port status (Fiber models only) Environmental Operating Temperature Commercial Models (IDS-108F) 0°C to 60°C (32°F to 140°F) Industrial Models (IDS-108F-XT) -40°C to 75°C (-40°F to 167°F) Storage Temperature Commercial Models (IDS-108F) -25°C to 70°C (-13°F to 158°F) - Page 15 40 km TX: 1310 Min:-3 Min:-23 IDS-108F-DS2SC40 (XT) 2 x SC duplex 24.9 miles RX:1310 Max:-5 Max:-3 40 km TX: 1310 Min:-3 Min:-23 IDS-108F-DS2ST40 (XT) 2 x ST duplex 24.9 miles RX:1310 Max:-5 Max:-3 IDS-108F installation Guide - 15 -...
-
Page 16: Contacting Technical Support
Warranty / Registration http://www.perle.com/support_services/warranty.shtml Copyright © 2014 Perle Systems Limited. All rights reserved. No part of this document may be reproduced or used in any form without written permission from Perle Systems Limited - 16 - IDS-108F Installation Guide...
Need help?
Do you have a question about the IDS-108F and is the answer not in the manual?
Questions and answers