Subscribe to Our Youtube Channel
Related Manuals for Perle IDS-710
Summary of Contents for Perle IDS-710
- Page 1 IDS-710 Hardware Installation Guide Managed Industrial Ethernet Switches Updated: December 2020 Version: A.15.12.2020 Document Part# 5500471-10 www.perle.com...
- Page 2 Modifications to this product not authorized by Perle could void the FCC approval and negate your authority to operate the product. Perle Systems Limited reserves the right to make changes without further notice, to any products to improve reliability, function, or design.
-
Page 3: Table Of Contents
Table of Contents Preface ......................2 Overview . -
Page 4: Preface
Switch. It covers hardware features as well as installation and operation of the switch. This document does not cover how to configure your Perle IDS Switch. Information to configure your Perle IDS Switch can be found in the IDS PRO Feature Set User Guide. Package Contents •... -
Page 5: Overview
The table below gives a brief overview of the models covered in this guide. For more details and for the most up-to-date list of models, please refer to the product pages at: www.perle.com 10/100/1000 Base-T Fixed SFP Standard Models Software Set Temp Ethernet Ports Port PoE Enabled IDS-710 Standard IDS-710-XT Industrial IDS-710 Hardware Installation Guide... -
Page 6: Switch Models Views
Switch Models Views IDS-710 (including XT models) 1 – Reset / FS (Fast Setup) 6 – SFP slots 2 – Status LEDs 7 – 10/100/1000Base-T Ethernet Ports with PoE/PoE+/PoE++ capability 3 – Terminal Block for Digital Input and 8 – Ethernet LED 1 Relay 4 –... - Page 7 100 meters (328ft) in length. SFP Slots The SFP slots can accommodate industry standard SFPs from Perle or other suppliers. These SFPs can be fiber or copper. The fiber SFP run at a speed of 1000 or 2500 Mbps.
-
Page 8: Port Status Indicators
LED 1: Green LED 2: Green 100 Mbps LED 1: Off LED 2: Green 10 Mbps On solid Port Link Random blinking Port Link and Activity Slow blinking Error disabled Rapid blinking Port in Fast Setup Mode IDS-710 Hardware Installation Guide... - Page 9 SFP Status LEDs State Description Green Fiber link established Green flashing Link/activity No Link Each SFP has a corresponding LED to indicate the current state of the fiber link. IDS-710 Hardware Installation Guide...
-
Page 10: Terminal Block Connectors
P2 (+/-) — Power Input 2. Either P1 or P2 can power the unit. When both are connected, one will act as a backup. IN(+/-) — Digital Input. Dry Contact. Relay — Normally Open (NO) relay. IDS-710 Hardware Installation Guide... -
Page 11: Installation
Warning: In case of malfunction or damage, no attempts at repair should be made. Do not dismantle the product. All repairs need to be made by a qualified Perle representative. Warning: For equipment installed within the same end-product enclosure ensure leads are segregated or insulate the leads from different circuits. -
Page 12: Connecting Power To The Ids Switch
To connect the digital input; 1. Ensure the power source is off prior to connection. 2. Strip 2x12-20AWG (3.31 mm² -0.52 mm²) twisted pair copper wires 7-8 mm. 3. Loosen the terminal block screws and connect wires into the terminals. IDS-710 Hardware Installation Guide... -
Page 13: Connecting The Console Port
• 8 data bits • 1 stop bit • No parity • None (flow control) 6. The PC will display the bootloader sequence. 7. Press Enter to display the setup prompt when the booting of the IDS is completed. IDS-710 Hardware Installation Guide... -
Page 14: Connecting Data Ports
Note: It may take a few seconds for the device to become active. By default the IDS switch will have Rapid Spanning Tree (RSTP) protocol enabled. This protocol will first check the network for any cabling loops prior to bringing the port up, in order to prevent network disruptions. IDS-710 Hardware Installation Guide... - Page 15 2. If the SFP module is equipped with a clasp, move it to the unlocked position and use the clasp to pull the SFP towards you. 3. If the SFP module is not equipped with a clasp, then with your fore finger and thumb, firmly grip the SFP and pull towards you. IDS-710 Hardware Installation Guide...
-
Page 16: Resetting The Switch
Press and hold the reset button • While continuing to hold the reset button, apply power to the switch • When the PWR LED goes from to YELLOW, release the reset button. The switch is now reset to factory default configuration. IDS-710 Hardware Installation Guide... - Page 17 Rapid blinking on the first available RJ-45 port to which the PC can be connected. Password Recovery When the switch is not in factory default, the "Fast Setup Mode" sequence will activate Password recovery. Note: The password recovery feature can be disabled in the software. IDS-710 Hardware Installation Guide...
-
Page 18: Configuring The Ids Switch
Web Device Manager The Perle Web Device Manager is an embedded Web based application that provides an easy to use browser interface for managing the switch. This interface provides the ability to configure and manage the switch. This is accessible through any standard desktop web browser. -
Page 19: Appendix A - Technical Specifications
Appendix A - Technical Specifications This appendix provides the technical specification for the IDS-710(-XT) switches. Technical Specification Power Power Connector • 8-Pin Removable Terminal Block (4 pins are used for power 1 and Power 2) • Grounding screw on metal chassis •... - Page 20 Technical Specification SFP slot • 2 SFP slots provided • Supports 1000Base-X and 2500Base-X SFP mod- ules supplied by Perle, Cisco or other manufactur- ers of MSA compliant SFPs SFPs supporting SGMII protocol are also supported (example 1000Base-T) Console port •...
- Page 21 IEC/EN 61000-4-11 IEC/EN 61000-6-2 (General Immunity in Industrial Environments) Laser Safety Class 1 Laser safety requirements for those models with fixed fiber transceiver modules EN 60825-1:2007 FDA/CDRH 21 CFR1040.10 and 21 CFR1040.11 Environmental Reach RoHS WEEE Compliant IDS-710 Hardware Installation Guide...
- Page 22 Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. www.perle.com/support_services/support_request.shtml Warranty / Registration This product is covered by the Perle Ethernet Switches Warranty. Details can be found at: https://www.perle.com/support_services/warranty.shtml IDS-710 Hardware Installation Guide...
-
Page 23: Appendix B - Sample Labels
Appendix B - Sample Labels IDS-710 Hardware Installation Guide... -
Page 24: Appendix C - Mechanical Drawings
Appendix C - Mechanical Drawings IDS-710 Hardware Installation Guide... -
Page 25: Appendix D - Din Rail And Wall Mounting
2. Insert a flat blade screwdriver into the slot and twist the base to release the clip. Alter- natively a downward force on the clip will release the clip. 3. When the clip is released, pull the bottom of the switch out slightly and remove the switch from the DIN rail. IDS-710 Hardware Installation Guide... - Page 26 Wall Mounting the IDS If you have purchased the optional wall mounting kit (Perle part number: 07010290) then proceed as below: 1. Remove the DIN rail clip from the rear panel on the IDS switch. 2. Attach the wall mount plates to the IDS switch as shown below using the screws provided in the kit.
- Page 27 IDS-710 Hardware Installation Guide...
-
Page 28: Appendix E - Ids Maintenance
Do not use solvents or cleaning agents on this unit • Keep vent holes clear of debris • If case gets dirty wipe with a dry cloth • Ensure all cables are in good working condition • Replace any frayed cables or cables without clips IDS-710 Hardware Installation Guide... -
Page 29: Appendix F - Cables And Connectors
(NIC-type or HUB/Switch-type) connected to the port. Requirements: • Cat 5 UTP or STP. Cat 5e cables are preferable when running 1000Mbps speeds. • 24-22 AWG (0.20mm - 0.33mm • Straight through or Ethernet Crossover cable Ethnernet Connector - 8-pin RJ45 IDS-710 Hardware Installation Guide...
Need help?
Do you have a question about the IDS-710 and is the answer not in the manual?
Questions and answers