1. Manuals
  2. Brands
  3. Acorp Manuals
  4. Motherboard
  5. 6M810E
  6. User manual

Acorp 6M810E User Manual

Micro-atx form factor main board
Hide thumbs Also See for 6M810E:
Table of Contents

Advertisement

Quick Links

6M810E/6M810ECD
Micro-ATX Form Factor
Main Board
User' s Manual
( ver 2.0 )

Advertisement

Table of Contents
loading

Related Manuals for Acorp 6M810E

Summary of Contents for Acorp 6M810E

  • Page 1 6M810E/6M810ECD Micro-ATX Form Factor Main Board User' s Manual ( ver 2.0 )
  • Page 2 Copyright Copyright ©2001 by this company. No part of this document may be reproduced, transmitted, transcribed, stored in a retrievable system, or translated into any natural or computer language, in any form or by any means without prior written permission. This manual and the information contained herein are protected by copyright.
  • Page 3 Warning and disclaimer This manual is designed to provide information about the Pentium® III / Celeron & Cyrix III main board. Meticulous efforts have been made to make this manual as accurate as possible, but no warranty or fitness is implied. All the information is provided on an 'as is' basis.

  • Page 4: Table Of Contents

    Table of contents Chapter 1 Introduction…………………..….…..….….. Overview…………………………………………………………….1 Specifications………………………………………………………..3 Limitation……… ………………………………………………..5 Notice of Hardware Installation……..…………………………..6 Notice of CD Driver Installation…..………..….………….…..……….….7 Chapter 2 Installation…………………………………..8 Layout Reference……………………………………..…….……..8 Jumper Setting…………………………………………..….……..9 2-2-1 JP10 : Audio Function Selector……………………………………9 2-2-2 SMART: Smart Card Reader Connector…..……………..…….10 2-2-3 CMOS Status…………….………………………………………..11 Connectors..………………………………..…………………..….12 2-3-1 Front Panel……………….……………………..…..……………12...
  • Page 5 Chapter 3 BIOS Setup………………………………..23 Award BIOS CMOS Setup………………………………………23 3-1-1 Standard CMOS Features…...……………….…………….……24 3-1-2 Advanced BIOS Features……………………………………..27 3-1-3 Advanced Chipset Features ………..…………...…….…..……32 3-1-4 Integrated Perpherals……………..…………………………..35 3-1-5 Power Management Setup………….…….…………….……..39 3-1-6 PNP/PCI Configuration Setup……………………………...…..42 3-1-7 Frequency/Voltage Control.……...……………………….……43 3-1-8 Supervisor/User Password…………….………………………….44 3-1-9 Load Optimized Defaults………..………………………….…47 3-1-10 Save and Exit Setup………..……...………..…………...………48 3-1-11 Quit Without Saving….…..…………………...………...………49 Chapter 4 Appendix…………………….…………..

  • Page 6: Chapter 1 Introduction

    33MB/s. It supports back to back sequential CPU to PCI Memory writes to PCI Burst Write for full PCI throughput. The AMR Slot is designed to fit low cost A(Audio) M(Modem) R(Riser) or MR card. 6M810E Main Board...
  • Page 7 CPU Installation This model is a jumperless main board, there is no selector needed for CPU frequency selection,, Please load optiomized Defaults in the CMOS setting,. The main board will automatically detect CPU frequency (66/100/133 MHz) 6M810E Main Board...

  • Page 8: Specifications

    ● PCB Board size : 17.0cm x 24.5cm, Micro ATX form factor ● Optional Items : • TV-out (Chrontel CH7007 chip is needed) Caution : System needs at least PC-100 memory & over 5VSB 1 Ampere current ≧ ATX power supply for this main board 6M810E Main Board...
  • Page 9 ● Other features • Modem ring on • Windows 95/98 power off • Keyboard wake-up • Mouse wake-up • DMI, ACPI supported BIOS 6M810E Main Board...

  • Page 10: Limitation

    ∗ Must use PC-100 specification DIMM (PC-133 for i810E only) ∗ Must use over 5VSB ≧ 1 Ampere current. 2. Software (Driver or BIOS): ∗ Windows 95 & 98 don’t provide driver (utilities) for i810 chipset. User needs to install driver carefully before using this board 6M810E Main Board...

  • Page 11: Notice Of Hardware Installation

    During hardware installation, be sure that there is no power connected in this period. C. Avoid ESD (Electrical Static Discharge) While working with this main board, always wear a grounded wristband or ankle strap to avoid ESD (Electrical Static Discharge). 6M810E Main Board...

  • Page 12: Notice Of Cd Driver Installation

    Driver of ALC100 & ALC200 is the same. Go to the IntelAC97 directory & run either ALC200 (or ALC100) setup.exe file. Due to “CIH” virus will damage BIOS completely, user needs to load Pc-cillin anti-virus software when sets up system. 6M810E Main Board...

  • Page 13: Chapter 2 Installation

    Chapter 2 Installation 2-1 Layout Reference COM1 MIC/LINE-IN/LINE-OUT GAME MOUSE ATX PWR COM2 SDRAM Intel 810 SDRAM FW82810E Intel PGA370 FW82801AA DIMM1 DIMM2 6M810E Main Board...

  • Page 14: Jumper Setting

    AMR card installed on slot, set “2-3” to enable on board audio function and use MR card installed on slot. JP10 : Audio Function Selector Disable on board Enable on board AC-97 CODEC AC-97 CODEC 6M810E Main Board...

  • Page 15: Smart: Smart Card Reader Connector

    The Smart Card is capable of providing secured storage facilities for sensitive personal information (such as Private keys, Account numbers, Passwords, Medical information, etc…). The Smart Card Reader can be used for a broad range of application in GSM, ID, pay TV, banking, … and so forth. 6M810E Main Board...

  • Page 16: Cmos Status

    Step 5: Link the power cable to the connector & connect AC power to power supply. Step 6: Turn on system power. If you’d like to set password, press “Del” Key during system boot up to enter CMOS setup and establish a new password. 6M810E Main Board...

  • Page 17: Connectors

    There are many connectors on this main board. Refer to the following pages for details. 2-3-1 Front Panel Front panel has connectors such as “POWER-LED,” “SPEAKER,” “RESET,” “HD-LED,” “TB-LED,” ”POWER-SW.” Please refer to the following further information. 6M810E Main Board...
  • Page 18 Hard Disk LED. TURBO-LED is a 2-pin Berg strip on case front panel indicates the current speed status of system. POWER-SW. is a 2-pin connector which controls power “on” and “off”. 6M810E Main Board...

  • Page 19: Back Panel Connectors

    2-3-2 Back Panel Connectors Back Panel Connectors are GAME Port, MIC, LINE-IN, LINE-OUT, COM1/ COM2, LPT, USB, PS/2 keyboard, and PS/2 mouse on case back panel. Refer to below details. Game port PS/2 Mouse Keyboard COM1 LINE-OUT LINE-IN COM2 6M810E Main Board...

  • Page 20: Com 1/Com2

    Universal Serial Bus connector, marked as “USB,” is used to connect USB devices. There are 2 USB connectors on this main board. Midi/Game Port & External Audio Connectors Midi/Game port has 15 pins connecting to the game joystick. External Audio connectors are “LINE-OUT, LINE-IN, MIC-IN” for audio functions. 6M810E Main Board...

  • Page 21: Atx Power Supply Connector

    Push the switch again to turn off the power to the system board. To support i810 chipset, we suggest that Pin 17 signal 5VSB on ATX Power supply should be able to offer at least 750 mA driving ability. 6M810E Main Board...

  • Page 22: Fan Connectors

    2-3-4 Fan Connectors There are 3 fan connectors on this system board, and it is marked as “FAN”. Each fan connector has three pins. Fan Signal 6M810E Main Board...

  • Page 23: Connector

    PDA and printers. This connector supports HPSIR, ASKIR, and Fast IR. Attach Infrared module to IR connector. Be sure to put in the right orientation during attachment. I.R.:INFRA-RED CONNECTOR IR3 IR4 IR3(normal IR) IR4(consumer IR) IRRX CIRRX IRTX CIRTX 6M810E Main Board...

  • Page 24: Floppy Disk Connector

    2-3-6 Floppy Disk Connector Floppy Disk connector has 34 pins and is used to attach the floppy drive cable. 6M810E Main Board...

  • Page 25: Ide1 & Ide2

    IDE1 and IDE2 are 39 – pin IDE connectors (Ultra 66). IDE1 is primary channel, and IDE2 is secondary channel. Each channel supports 2 IDE devices, and 4 devices in total for this main board. IDE2 IDE1 6M810E Main Board...

  • Page 26: Cd1/Cd2: Cd-In

    2-3-8 CD1& CD2: CD-in CD1 & CD2 is a CD ROM external audio input signal to line-out (speaker) of the main board. CD2 CD1 6M810E Main Board...

  • Page 27: Dimm Installation

    Insert the module as shown. Due to different number of pins on either side of the breaks, the module will only fit in the orientation as shown. SDRAM DIMM modules have different pin contacts on each side and therefore have a higher pin density. 3.3V SDRAM memory supports PC-100 DIMM or above. 6M810E Main Board...

  • Page 28: Chapter 3 Bios Setup

    When a selection is made, the menu of the selected item will appear. So the user can modify associated configuration parameters. 6M810E Main Board...

  • Page 29: Standard Cmos Features

    BIOS and displayed for your reference. When a field is highlighted (direction keys to move cursor and <Enter> key to select). The entries in the field will be changed by pressing <PageDown> or <PageUp> key or user can enter new data directly from the keyboard. 6M810E Main Board...
  • Page 30 "LBA" or "LARGE" or "CHS". However, if your hard disk cylinder is more than 1024 and does not support the LBA function, you have to set at "LARGE.” Select "NORMAL" if your hard disk supporting cylinder is below 1024. 6M810E Main Board...
  • Page 31 “auto”, the hard disk size and model will be auto detected on display during POST. Note2: "halt on" is to determine when to halt the system by the BIOS if error occurred during POST. 6M810E Main Board...

  • Page 32: Advanced Bios Features

    [F1] key to display help message of the selected item. This setup program also provide 2 convenient ways to load the default parameter data from BIOS [F6] and [F7] area if shown data is corrupted. This provides the system a capability to recover from any possible error. 6M810E Main Board...
  • Page 33 This category determines which drive the system searches first. System will search in turn for floppy disk drive; then hard disk drive, and finally Floppy drive. Default value is “FLOPPY”. Options are as below: FLOPPY; LS120; HDD-0; SCSI; CDROM; HDD-1; HDD-2; HDD-3; ZIP100; LAN; Disabled 6M810E Main Board...
  • Page 34 BIOS will determine if the floppy disk drive is 40 or 80 tracks. 360k type is 40 tracks while 720K/1.2M and 1.44M are all 80 tracks. Default value is enabled. :Enabled :Disabled (default) BOOT UP NUMLOCK STATUS :On (default) :Off GATE A20 OPTION :Normal :Fast (default) 6M810E Main Board...
  • Page 35 After setting password in BIOS CMOS in CMOS setup “Supervisor Password” User menu Password,” it protects BIOS CMOS setup. System Security protection This function secures the system under in system boot-up system boot-up and BIOS setup after setting & BIOS setup password. 6M810E Main Board...
  • Page 36 This option is especially set for OS2 operating system. Set “OS2” for RAM memory over 64MB and set “Non-OS2” for other operating systems like Windows® 95/98 or NT. :Non-OS2 (default) :OS2 HDD S.M.A.R.T CAPABILITY :Enabled :Disabled (default) REPORT NO FDD FOR WIN 95 :No (default) :Yes 6M810E Main Board...

  • Page 37: Advanced Chipset Features

    3-1-3 Advanced Chipset Features 6M810E Main Board...
  • Page 38 MEMORY HOLE AT 15M-16M: this field enables a memory hole in main memory space. CPU cycles matching an enabled hold are passed on to PCI note that a selection can not be changed while the L2 cache is enabled. :Enabled :Disabled (default) 6M810E Main Board...
  • Page 39 :Disabled LOCAL MEMORY FREQUENCY :100MHz(default) :133MHz ONBOARD DISPLAY CACHE SETTING CAS# Latency :3(default) PAGING MODE CONTROL :Close :Open (default) RAS-TO-CAS OVERRIDE :by CAS # LT(default) :Override(2) RAS# TIMING :Slow :Fast (default) RAS# PRECHARGE TIMING :Slow :Fast (default) 6M810E Main Board...

  • Page 40: Integrated Peripherals

    ONCHIP SECONDARY PCI IDE :Enabled(default) :Disabled IDE PRIMARY MASTER PIO This feature detects your primary master hard disk device. :Auto (default) :Mode 0,1,2,3,4 IDE PRIMARY SLAVE PIO This feature detects your primary slave hard disk device. :Auto (default) :Mode 0,1,2,3,4 6M810E Main Board...
  • Page 41 IDE PRIMARY SLAVE UDMA :Auto(default) :Disabled IDE SECONDARY MASTER UDMA :Auto(default) :Disabled IDE SECONDARY SLAVE UDMA :Auto(default) :Disabled USB CONTROLLER :Enabled(default) :Disabled USB KEYBOARD SUPPORT :Enabled :Disabled(default) INIT DISPLAY FIRST :PCI Slot (default) :Onboard AC97 AUDIO :Auto(default) :Disabled 6M810E Main Board...
  • Page 42 Select an address and corresponding interrupt for the first serial port. :Auto (default) :2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, 3F8/IRQ4, Disabled ONBOARD SERIAL PORT 2 Select an address and corresponding interrupt for the second serial port. :Auto (default) :2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, 3F8/IRQ4, Disabled UART MODE SELECT :Normal (default) :IrDA 6M810E Main Board...
  • Page 43 Select a DMA channel for the parallel port for using during ECP mode. :3 (default) PWRON AFTER PWR-FAIL :Off (default) :On, Former-Sts GAME PORT ADDRESS :201 (default) :209, Disabled MIDI PORT ADDRESS :300, 330 :Disabled (default) MIDI PORT IRQ :10 (default) 6M810E Main Board...

  • Page 44: Power Management Setup

    3-1-5 Power Management Setup ACPI FUNCTION :Enabled(default) :Disabled POWER MANAGEMENT :User Define(default)--users can configure their own power management :Min Saving :Max Saving VIDEO OFF METHOD :DPMS(default) :Blank Screen :V/H Sync+Blank 6M810E Main Board...
  • Page 45 When Enabled, you can set the date and time on RTC (real-time clock) alarm awaken a system which has been powered down. :Enabled :Disabled (default) DATE(OF MONTH) ALARM/TIME(HH:MM:SS) You can set the date (of month) and timer (hh:mm:ss), any event occurring will awaken a system which has been powered down. 6M810E Main Board...
  • Page 46 RELOAD GLOBAL TIMER EVENTS Primary IDE0 :Enabled :Disabled (default) Primary IDE1 :Enabled :Disabled (default) Secondary IDE0 :Enabled :Disabled (default) Secondary IDE1 :Enabled :Disabled (default) FDD. COM, LPT Port :Enabled :Disabled (default) PCI PIRQ (A-D)# :Enabled :Disabled (default) 6M810E Main Board...

  • Page 47: Pnp/Pci Configuration Setup

    The table will show the below items: IRQ-3 ~ IRQ15 assigned to PCI DEVICES. The user can adjust the shown items as required. :Auto (ESCD) The table will not show the above items, and the system will automatically assign the above setup. PCI/VGA PALETTE SNOOP :Disabled (default) :Enabled 6M810E Main Board...

  • Page 48: Frequency/Voltage Control

    : x 3.5 ; x 4 ; x 4.5 ; x 5 ; x5.5 ; x 6 ; x 6.5 ; x 7 ; x 7.5; x 8 This selection is reserved for manufacturers to pass CE test only not available for users. 6M810E Main Board...

  • Page 49: Supervisor/User Password

    EXIT SETUP,” and “EXIT WITHOUT SAVING.” 1. How to set “Supervisor Password” & “User Password” The setup of “Supervisor Password” and “User Password” has the same steps. Step 1: Enter Password --Press <Enter> after appointing the password. 6M810E Main Board...
  • Page 50 After setting password, enter “Security Option” in “BIOS Features Setup.” There are 2 options “Setup” & “System.” “Setup” will only secure CMOS setup through password. “System” is to secure PC sytem and password is required during system boot-up in addition to CMOS setup. 6M810E Main Board...
  • Page 51 When it shows “Enter Password”, press the <Enter> key instead of entering a new password when "ENTER PASSWORD" appears. It will inform “PASSWORD DISABLED PRESS ANY KEY TO CONTINUNE.” Then, press any key as instructed to disable the password. 6M810E Main Board...

  • Page 52: Load Optimized Defaults

    A line will appear on screen asking if you want to load the setup default values. Press the <Y> key and then press the <Enter> key. The setup defaults will then load. If not, enter <N>. 6M810E Main Board...

  • Page 53: Save And Exit Setup

    3-1-10 Save & Exit Setup The "Save & Exit Setup" option will bring you back to boot up procedure with all the changes you have made which are recorded in the CMOS RAM. 6M810E Main Board...

  • Page 54: Quit Without Saving

    3-1-11 Quit Without Saving The "Quit Without Saving" option will bring you back to normal boot up procedure without saving any data into CMOS RAM. All of the old data in the CMOS will not be changed. 6M810E Main Board...

  • Page 55: Chapter 4 Appendix

    E0000-EEFFF Available for UMB EF000-EFFFF Video service routine for monochrome & CGA adapter F0000-F7FFF BIOS CMOS setup utility F8000-FCFFF BIOS runtime service routine (2) FD000-FDFFF Plug and play escd data area FE000-FFFFF BIOS runtime service routine (1) 6M810E Main Board...

  • Page 56: I/O Map

    Parallel port 2 2B0-2DF Graphics adapter controller 2F8-2FF Serial port 2 360-36F Network ports 378-37F Parallel port 1 3B0-3BF Monochrome & parallel port adapter 3C0-3CF EGA adapter 3D0-CDF CGA adapter 3F0-3F7 Floppy disk controller 3F8-3FF Serial port-1 6M810E Main Board...

  • Page 57: Time & Dma Channels Map

    DMA channel 1 onboard ECP (option) DMA channel 2 floppy disk (ITE chip) DMA channel 3 onboard ECP (default) DMA channel 4 cascade for DMA controller 1 DMA channel 5 available DMA channel 6 available available DMA channel 7 6M810E Main Board...

  • Page 58: Interrupt Map

    5. parallel port 2 6. floppy disk (ITE chip) 7. parallel port 1 8. RTC clock 9. available 10. available 11. available 12. PS/2 mouse 13. math coprocessor 14. onboard hard disk (IDE1) channel 15. onboard hard disk (IDE2) channel 6M810E Main Board...

  • Page 59: Rtc & Cmos Ram Map

    Base Memory Low Byte Base Memory High Byte Extension Memory Low Byte Extension Memory High Byte 19-2D 2E-2F Reserved for Extension Memory Low Byte Reserved for Extension Memory High Byte Information Flag 34-3F Reserved 40-7F Reserved for Chipset Setting Data 6M810E Main Board...

  • Page 60: Isa I/O Address Map

    Serial Port 2 (RS-232-C) 300 - 31F Prototype Card 360 - 363 PC Network (Low Address) 364 - 367 Reserved 368 - 36B PC Network (High Address) 36C - 36F Reserved 378 - 37F Parallel Printer Port 1 6M810E Main Board...
  • Page 61 Cluster Adapter 3 22E1 GPIB Adapter 1 2390 - 2393 Cluster Adapter 4 42E1 GPIB Adapter 2 62E1 GPIB Adapter 3 82E1 GPIB Adapter 4 A2E1 GPIB Adapter 5 C2E1 GPIB Adapter 6 E2E1 GPIB Adapter 7 6M810E Main Board...

  • Page 62: Chapter 5 Q & A

    CMOS checksum error It indicates the CMOS checksum is incorrect. Load the default values in BIOS to solve this problem. This error may result from a weak BIOS, so replace a new BIOS if necessary. 6M810E Main Board...
  • Page 63 12. Secondary master hard disk fail The BIOS finds an error in the secondary slave master hard disk drive. 13. Secondary slave hard disk fail The BIOS finds an error in the secondary slave IDE hard disk drive. 6M810E Main Board...

This manual is also suitable for:

6m810ecd

Table of Contents