Energer ENB539TAS User Manual page 5

800w table saw
Hide thumbs Also See for ENB539TAS:
Table of Contents

Advertisement

FR
GB
ENB539TAS by Energer
IE
IE
General safety
11 Do not abuse the cord
> Never yank the cord to disconnect it from the socket.
> Keep the cord away from heat, oil and sharp edges.
12 Secure work
> Where possible use clamps or a vice to hold the work.
> It is safer than using your hand.
13 Do not over reach
> Keep proper footing and balance at all times.
14 Maintain tools with care
> Keep cutting tools sharp and clean for better and safer performance.
> Follow instruction for lubricating and changing accessories. Inspect tool cords
periodically and if damaged have them repaired by an authorized service facility.
Inspect extension cords periodically and replace if damaged. Keep handles dry,
clean and free from oil and grease.
15 Disconnect tools
> When not in use, before servicing and when changing accessories such as
blades, bits and cutters, disconnect tools from the power supply.
16 Remove adjusting keys and wrenches
> Form the habit of checking to see that keys and adjusting wrenches are removed
from the tool before turning it on.
17 Avoid unintentional starting
> Ensure switch is in "off" position when plugging in.
18 Use outdoor extension leads
> When the tool is used outdoors, use only extension cords intended for outdoor
use and so marked.
19 Stay alert
> Watch what you are doing, use common sense and do not operate the tool when
you are tired.
20 Check damaged parts
> Before further use of tool, it should be carefully checked to determine that it will
operate properly and perform its intended function.
> Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation.
> A guard or other part that is damaged should be properly repaired or replaced by
an authorised service centre unless otherwise indicated in this instruction
manual.
> Have defective switches replaced by an authorised service centre.
> Do not use the tool if the switch does not turn it on and off.
21 Warning
> The use of any accessory or attachment other than one recommended in this
instruction manual may present a risk of personal injury.
22 Have your tool repaired by a qualified person
> This electric tool complies with the relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts, otherwise this may
result in considerable danger to the user.
08
Technical and legal
information
ENB539TAS by Energer
Additional safety
> The bench-type circular saw is designed for the slitting and cross-cutting of all
types of timber, commensurate with the machine's size. The machine is not to be
used for cutting any type of round wood.
> The machine is to be used only for its prescribed purpose.
> Any use other than that mentioned is considered to be a case of misuse. The
user/operator and not the manufacturer shall be liable for any damage or injury
resulting such cases of misuse. The machine is to be operated only with suitable
saw blades. It is prohibited to use any type of cutting-off wheel.
> Use only saw blades recommended by the manufacturer, which confirm to EN
847-1, with a warning. When changing the saw blade, beware that the thickness of
the body of the saw blade shall not be more than the thickness of the splitter
(riving knife).
> Take care that the selection of the saw blade is suitable for the material to be cut.
> To use the machine properly you must also observe the safety regulations, the
assembly instructions and the operating instructions to be found in this manual.
> All persons who use and service the machine have to be acquainted with this
manual and must be informed about its potential hazards.
It is also imperative to observe the accident prevention regulations in force in your
area.
> The same applies for the general rules of occupational health and safety.The
manufacturer shall not be liable for any changes made to the machine nor for any
damage resulting from such changes.
>
Even when the machine is used as prescribed it is still impossible to eliminate
certain residual risk factors. The following hazards may arise in connection with
the machine's construction and design:
>
Contact with the saw blade in the uncovered saw zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if essential ear-muffs are not worn.
• Harmful emissions of wood dust when the machine is used in closed rooms.
>
Please note that our equipment has not been designed for use in commercial,
trade or industrial applications.Our warranty will be voided if the machine is used
in commercial, trade or industrial businesses or for equivalent purposes.
>
Wear suitable personal protective equipment when necessary, this could include
a) Hearing protection to reduce the risk of induced hearing loss.
b) respiratory protection to reduce the risk of inhalation of harmful dust.
c) wear gloves when handling saw blades and rough material. Saw blades shall be
carries in a holder whenever practicable.
>
Connect circular saws to a dust-collecting device when sawing wood. The
operator shall be informed of the factors that influence exposure of dust e.g. type
of material being machined and importance of local extraction (capture or
source) and proper adjustment of hoods/baffles/chutes.
Technical and legal
GB
information
IE
09

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ENB539TAS and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents