Related Manuals for Clarke JETSTAR 1800
Summary of Contents for Clarke JETSTAR 1800
- Page 1 JETSTAR 1800 JETSTAR 1800 POWERWASHER POWERWASHER Part No. 7333060 0108 OPERATING & MAINTENANCE INSTRUCTIONS ©...
-
Page 2: Table Of Contents
7333060 Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. ALWAYS CONSULT THE MACHINE’S DATA PLATE CONTENTS Specifications .................. - Page 3 Before attempting to use your Jetstar 1800, please read this instruction manual thoroughly and follow all instructions carefully. By doing so you will ensure the safety of yourself and that of others around you, and you can look forward to it giving you long and satisfactory service.
-
Page 4: Safety Precautions
5. Never operate the machine with any of the covers removed. 6. Do not, attempt any electrical or mechanical repair. If you have a problem with your machine contact your local dealer or Clarke Customer Services Dept., tel: 020 8988 7400 7. -
Page 5: Parts And Service Contacts
PARTS & SERVICE CONTACTS For Spare Parts and Service, please contact your nearest dealer, or CLARKE International, on one of the following numbers. PARTS & SERVICE TEL: 020 8988 7400 PARTS & SERVICE FAX: 020 8558 3622 e-mail as follows: PARTS: Parts@clarkeinternational.com... -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: THIS MACHINE IS DOUBLE INSULATED This product is provided with a standard 13 amp, 230 volt (50Hz). BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used. IMPORTANT: The wires in the mains lead should be wired up in accordance with the following colour code: Blue... -
Page 7: Pre-Assembly Checks
PRE- ASSEMBLY CHECKS Before assembling your new Jetstar 1800 Powerwasher, check to ensure that all parts listed below are included. Item 1 Powerwasher with cable and plug Item 2 Trigger/Handle assembly with high pressure hose Item 3 Lance Extension Item 4... -
Page 8: Assembly And Preparation For Use
ASSEMBLY AND PREPARATION FOR USE. A. Water Supply Hose Fig.1 The inlet hose adapter (1), should be attached to the water inlet ensuring the filter, within the port and sealing ring within the adapter are in both in place Attach a suitable hose to the inlet hose adapter, using a worm drive clip, or more commonly used, a Quick Fit Coupling as shown at 2, Fig 1. -
Page 9: Operation
B. Lance At the opposite end to the nozzle is a spigot with two integral lugs, and a rubber O-ring. Ensure the O-ring is in place and in good condition. Insert the spigot end of the nozzle into the Fig.4 handle/lance assembly. - Page 10 As soon as you pull the trigger again, water at pressure will be ejected. This process will continue for as long as the machine is switched ON. WARNING! Ensure the operator is aware that when the trigger is pulled, water at high pressure can cause the lance to kick fiercely - it should therefore be held firmly.
-
Page 11: Thermal Overload
Use ONLY those detergents recommended for use with power washers, such as CLARKE Traffic Film Remover which is a powerful low foaming agent for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer. -
Page 12: Care & Maintenance
If the seals are stuck however, contact your Clarke dealer for advice. Water input filter Located behind the water inlet, this filter should be removed for cleaning after every 10 hours of use (or less if water is contaminated). -
Page 13: Troubleshooting
Dirty high pressure nozzle in spray Clean high pressure nozzle Irregular jet produced ACCESSORIES The range of accessories listed below may be purchased from your CLARKE dealer. Item Part No. 5 Litres Detergent (Traffic Film Remover) ......3050821 25 Litres Detergent (Traffic Film Remover) ......3050820... -
Page 14: Spare Parts List And Diagram
Handle ..............ND180008 SPARE PARTS & SERVICING For Spare Parts or Servicing, please contact your nearest dealer, or CLARKE International, on one of the following numbers. PARTS & SERVICE - 020 8988 7400 PARTS & SERVICE FAX - 020 8558 3622 PARTS E-MAIL - Parts@clarkeinternational.com... -
Page 15: Declaration Of Conformity
When disposing of this product, do not dispose of with general waste. It must be disposed of according to the laws governing Waste Electrical and Electronic equipment, at a recognised disposal facility.