Analog In/Out Word Clock Int; Group Inspection; Recall Inspection; 2Tr Out L/R - Yamaha 01v 96 Service Manual

c. Press the DISPLAY ACCESS [PAIR/GROUP] key a
few times, switch to the OUT FADER GROUP fixed
screen, and press the [SEL 1]~[SEL 16] and [SEL
STEREO] keys and group the 17 faders.
w Group inspection
a. Operate the stereo master fader, repeat the delay
(about 3 seconds/100 mm) twice and repeat the
advance (about 1 second/100 mm) twice.
b. Operate the Channel 1 fader, repeat the delay (about
3 seconds/100 mm) twice and repeat the advance
(about 1 second/100 mm) twice.
c. Check that there are no vibrating faders or extremely
late faders in the above operations
e Recall inspection
a. Press the LAYER [1-16] key and select Layers 1-16.
b. Press the DISPLAY ACCESS [SCENE] key to switch
to the SCENE MEMORY screen, then press the
SCENE MEMORY [
then press the [RECALL] key to recall 0.
c. Move all the faders all the way up, press the SCENE
MEMORY [ ] key or [
the [STORE] key and when the TITLE EDIT screen
is displayed, then select OK to store 1.
d. With the operation method in b., repeat two times
from the 0 recall to the 1 recall.
e. Check that there are no vibrating faders or extremely
late faders in the above operations.

2. ANALOG IN/OUT WORD CLOCK INT

96 kHz inspection
2-1. STEREO OUT L/R
Parameter Must be input from CH1(XLR).
q Gain (both L/R)
Input frequency Input level Regulated output level
1kHz +4dBu
w f characteristic (both L/R)
Parameter The permitted range uses 1 kHz as
the reference.
Input frequency Input level
20Hz +4dBu
40kHz +4dBu
e Residual noise (both L/R)
Parameter Switch STEREO OUT Off.
Permitted range
-86dBu or below
r L/R level difference
The range for the difference in the gain measured
with q is regulated as follows.
Permitted range
Within 1dB
] key or [ ] key to select 0,
] key to select 1, then press
Permitted range
+4dBu +4±2dBu
Permitted range
-1.5~+0.5dB
-1.5~+0.5dB
t Crosstalk between left and right
Parameter PAN L swung to cut off.
Input frequency Output level (L) Permitted range (R)
1kHz +22dBu
The right side must be the same.
y Maximum output (both L/R)
Input frequency Permissible range Permissible range (
1kHz +24±0.5dBu

2-2. 2TR OUT L/R

Parameter Must be input from CH1(XLR).
q Gain (both L/R)
Input frequency Input level Regulated output level
1kHz +4dBu
w f characteristic (both L/R)
Parameter The permitted range uses 1 kHz as
the reference.
Input frequency Input level
20Hz +4dBu
40kHz +4dBu
2-3. OMNI OUT 1~4
Parameters Must be input from CH1 (XLR).
BUS 1~4 ON with CH1 routing.
Assign Bus nCH to OMNI nCH with
an OUT PATCH.
BUS 1-4 MASTER FADER ON.
q Gain (OMNI OUT 1~4)
Input frequency Input level Regulated output level
1kHz +4dBu
w f characteristic (OMNI OUT 1~4)
Parameter The permitted range uses 1 kHz as
the reference.
Input frequency Input level
20Hz +4dBu
40kHz +4dBu
e Residual noise (OMNI OUT 1~4)
Parameter Switch the BUS OUT Off.
Permitted range
-86dBu or below
r OMNI OUT 1-4 level difference
The range for the difference in the gain measured
with q is regulated as follows.
Permitted range
Within 1dB
01V96
-58dBu or below
distortion ratio
)
0.01% or below
Permitted range
-10dBV -10±2dBV
Permitted range
-1.5~+0.5dB
-1.5~+0.5dB
Permitted range
+4dBu +4±2dBu
Permitted range
-1.5~+0.5dB
-1.5~+0.5dB
77