Analog Input Spec; Analog Output Spec - Yamaha 01v 96 Service Manual

01V96

Analog Input Spec

Input PAD
0
INPUT A/B
1–12
20
INPUT 13–16
—
CH INSERT IN
—
1–12
2TR IN [L, R]
—
*1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit
is set to maximum gain. (All faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
*3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
*4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms.
All input AD converters (CH INPUT 1–16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz)
+48 V DC (phantom power) is supplied to CH INPUT (1–12) XLR type connectors via individual switches.
Three PHANTOM +48V switches CH1–4, 5–8, 9–12 turn on the phantom power for inputs 1–4, 5–8, 9–12 respectively.

Analog Output Spec

Output
STEREO OUT [L, R]
OMNI OUT 1–4
MONITOR OUT [L, R]
CH INSERT OUT 1–12
2TR OUT [L, R]
PHONES
*1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
*2. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
*3. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
*4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms.
All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz)
10
Actual Load For Use With
GAIN
Impedance Nominal
–60 dB
50–600 Ω
3k Ω Mics & 600 Ω
Lines
–16 dB
–26 dB
10k Ω 600 Ω Lines
+4 dB
10k Ω 600 Ω Lines
10k Ω 600 Ω Lines
Actual
For Use With
Source
Nominal
Impedance
150 Ω 600 Ω Lines
150 Ω 10k Ω Lines
150 Ω 10k Ω Lines
600 Ω 10k Ω Lines
600 Ω 10k Ω Lines
8 Ω Phones
100 Ω
40 Ω Phones
Input level
*1
Nominal
Sensitivity
before clip
–70 dB –60 dB –40 dB
(0.245 mV) (0.775 mV) (7.75 mV)
–26 dB –16 dB
(38.8 mV) (123 mV) (1.23 V)
–6 dB +4 dB +24 dB
(338 mV) (1.23 V) (12.28 V)
–36 dB –26 dB
(1.23 mV) (38.8 mV) (388 mV)
–6 dB +4 dB +24 dB
(388 mV) (1.23 V) (12.28 V)
–12 dB –2 dB +18 dB
(195 mV) (616 mV) (6.16 V)
–10 dB –10 dBV +10 dBV
(316 mV) (316 mV) (3.16 V)
Output level
Max.
Nominal
before clip
+4 dB +24 dB
XLR-3-32 type (Balanced)
(1.23 V) (12.28 V)
+4 dB +24 dB
Phone jack (TRS) (Balanced)
(1.23 V) (12.28 V)
+4 dB +24 dB
Phone jack (TRS) (Balanced)
(1.23 V) (12.28 V)
Phone jack (TRS) (Unbal-
–2 dB +18 dB
(616 mV) (6.16 V)
anced)
–10 dBV +10 dBV
RCA Pin Jack (Unbalanced)
(316 mV) (3.16 V)
4 mW 25 mW
Stereo Phone Jack (TRS)
12 mW 75 mW (Unbalanced)
Connector
Max.
A: XLR-3-31 type
*2
+4 dB (Balanced)
B: Phone jack
*3
(TRS) (Balanced)
–6 dB
Phone jack (TRS)
*3
(Balanced)
Phone jack (TRS)
*4
(Unbalanced)
RCA pin jack
(Unbalanced)
Connector
*1
*2
*2
*3
*4