Mode Check Display - Panasonic AJ-PX800G Operating Instructions Manual

No Item
Chromatic aberration compensation
28
function display
29 Lens extender display
Flash band compensation function
30
display
Dynamic range stretcher function
31
display
32 Scene file name display
33 Battery charge level indicator
34 P2 card remaining free space
35 Simultaneous recording mode display
36 High-sensitivity mode display
37 One clip recording mode status display
Recording/playback operation status
38
display
HD SDI REMOTE recording status and
39
4G/LTE connection status display
*1 May be displayed depending on other settings.
*2 Displayed when the remaining capacity becomes smaller.
*3 Displayed during shooting.
*4 Always displayed when [HD SDI REMOTE] is set or when 4G/LTE connection is set.

Mode check display

The camera settings and status can be displayed on the viewfinder.
Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the five screens are switched.
[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [CAC INFO] screen display → no
display
Each screen is displayed for approximately five seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed
moves to the next screen.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT]
[P2CARD STATUS]
[PROXY]
[NETWORK]
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[AUDIO]
[A.IN]
[LEVEL]
[F.VR]
Chapter 8 Display — Screen status display
Shooting Playback
—
l
—
l
—
l
—
l
—
l
l l
l l
—
l
—
l
—
l
l l
—
l
*4
— Displays the status of the signal output from the <SDI OUT/IN (OP)> terminal.
Displays the format of the signal output from the <SDI OUT/IN (OP)> terminal by [HD-SDI]/
[TYPE]
[SD-SDI].
Displays the superimposition status of characters selected in the main menu → [IN/OUT
[CHAR]
SEL] → [SDI OUT CHAR] by [ON]/[OFF].
Displays the status of the P2 card inserted in the card slot, remaining capacity, and total
used capacity.
The statuses of cards to be displayed are as follows:
—
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to "P2 card access LEDs and status of P2 cards" (page 43).
[TOTAL P2/mP2] Displays the remaining capacity/total capacity of slots 1 and 2 altogether.
[SLOT1] Displays the status of the P2 card in slot 1 and remaining capacity/total capacity.
[SLOT2] Displays the status of the P2 card in slot 2 and remaining capacity/total capacity.
Displays the media selection status for proxy recording.
[MEDIA]
[P2]/[P2&SD]/[OFF]
Displays the setting status for proxy recording mode.
[MODE]
[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]
[PROXY ERROR] Displays the operation error on the proxy module.
[NETWORK] Displays the network to be used and its status.
[SAMPLE RES] Displays the audio recording bits.
Displays the input status of each channel.
[CH1/2/3/4]
[FRONT] (front), [REAR] (rear), [W.L.] (wireless)
Displays the recording level adjustment method currently selected on each channel.
f [MANU]: Displayed when manual adjustment is set.
[CH1/2/3/4]
f [AUTO]: Displayed when automatic adjustment is set.
Settings are performed in the SmartUI [AUD01:LEVEL] screen.
Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to
[CH1/2/3/4]
which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].
– 157 –
<DISP/
<DISP/MODE
MODE CHK>:
CHK>: <OFF>
<CHK>
—
l
—
l
—
l
—
l
—
l
—*
l
2
—*
l
2
—
l
—
l
—
l
—*
l
3
—
l
*4
<DISP/MODE CHK>: <ON>
[OTHER DISPLAY]
[ALL] [PARTIAL] [USER]
l l
l l
l l
l l
—
l
—* —*
1 1
—* —*
1 1
—
l
l l
l l
l l
l l
*4 *4
l
l
l
l
l
—*
1
—*
1
l
l
l
l
l
*4