Panasonic AJ-PX800G Operating Instructions Manual page 127

Item
[START DELAY]
[PRE REC]
[ONE CLIP REC]
[SIMUL REC]
[DUAL CODEC [CODEC USAGE]
SETTING]
[PROXY REC MODE]
[STREAMING MODE]
[PROXY DISP]
[START TEXT MEMO]
[DF MODE]
[UBG MODE]
[VITC UBG MODE]
[REC META DATA] [LOAD]
[RECORD]
[USER CLIP NAME]
[CARD SERIAL]
Chapter 6 Menu Operations — Menu list
Selects whether to delay the recording start time by approximately one second when performing interval
recording or one-short recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform pre-recording. If [ON] is selected, pre-recording is performed for approximately
three seconds in HD, and for approximately seven seconds in SD.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform one-clip recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform simultaneous recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects media for recording proxy data.
[PROXY REC(P2)]: Records proxy data to a P2 card.
[PROXY REC(P2&SD)]: Records proxy data to both of a P2 card and SD memory card.
[STREAMING]: Outputs video stream.
[OFF]: Does not record proxy data or output streaming.
f Factory setting: [OFF]
If [CODEC USAGE] cannot be changed, change the [PROXY REC MODE] or [STREAMING MODE]
setting.
Sets the recording mode of proxy data.
[LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV]
f Factory setting: [HQ 2CH MOV]
Sets the transfer mode for streaming.
[LOW], [HQ], [AVC-G6]
f Factory setting: [HQ]
Selects whether to display proxy data recorded information or messages in the viewfinder.
[ON]: Displays proxy recording information and SD memory card remaining capacity at the start of
recording. Warning information is displayed at all times.
[OFF]: Displays proxy and SD memory card warning information for only three seconds when warning
occurs.
f Factory setting: [OFF]
Selects whether to automatically add a text memo at recording start position each time recording is started.
[ON], [OFF]
f Factory setting: [OFF]
Sets the counting method of the built-in time code generator.
[DF]: Uses the drop frame mode.
[NDF]: Uses the non-drop frame mode.
f Factory setting: [DF]
Selects the user bits mode.
[USER]: Selects the user bits value that has been set.
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
[EXT]: Records the user bits values currently input to the <TC IN/OUT> terminal.
[TCG]: The value of [TCG] is recorded as user bits.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[REGEN]: Reads the value recorded to the card and continuously records that value.
f Factory setting: [USER]
Selects the VITC user bits mode.
[USER/EXT]: When [UBG MODE] is [EXT], follows the value and when other than [EXT], records the user
value set in [USER].
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
[TCG]: The value of time code generator is recorded as user bits.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[REGEN]: Reads the value recorded to the card and continuously records that value.
f Factory setting: [USER/EXT]
Loads the metadata upload file saved to the SD memory card.
Sets whether to add loaded metadata at a recording.
[ON]: Adds metadata.
[OFF]: Does not add metadata.
f Factory setting: [OFF]
Sets data to be recorded to [USER CLIP NAME].
(When [RECORD] is [ON])
[TYPE1]: Records setting values of the loaded data.
[TYPE2]: Records the loaded data and counter value.
(When [RECORD] is [OFF])
[TYPE1]: Records the same value as [GLOBAL CLIP ID].
[TYPE2]: Records the same value as [CLIP NAME].
f Factory setting: [TYPE1]
Enables/disables the function for storing the text memo with the serial number or the type of card as
metadata.
[ON], [OFF]
f Factory setting: [OFF]
– 127 –
Description of settings