[Card Functions] - Panasonic AJ-PX800G Operating Instructions Manual

Memory card camera-recorder
Hide thumbs Also See for AJ-PX800G:
Table of Contents

Advertisement

Item
[TYPE A END]
[TYPE B FULL]
[TYPE B NEAR END]
[TYPE B END]
[TYPE C FULL]
[TYPE C NEAR END]
[TYPE C END]
[BATT STAT NEAR END] Selects the near end percent value.
[BATT STAT END]
[ENDURA STAT NEAR
END]
[ENDURA STAT END]

[CARD FUNCTIONS]

Configure the settings regarding reading/writing of the scene files and user files to SD memory cards.
Item
[SCENE FILE]
[USER FILE]
[CAC FILE]
Chapter 6 Menu Operations — Menu list
Selects the end voltage in steps of 0.1 V when [TYPE A] is selected in the main menu → [BATTERY
SETUP] → [BATTERY SELECT].
The [TYPE A] factory setting corresponds to the IDX ENDURA ELETE.
[11.0V]...[15.0V]
f Factory setting: [12.5V]
Selects the voltage for full display in steps of 0.1 V when [TYPE B] is selected in the main menu →
[BATTERY SETUP] → [BATTERY SELECT].
The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC.
[13.0V]...[17.0V]
f Factory setting: [15.9V]
Selects the near end voltage in steps of 0.1 V when [TYPE B] is selected in the main menu → [BATTERY
SETUP] → [BATTERY SELECT].
The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC.
[11.0V]...[15.0V]
f Factory setting: [12.9V]
Selects the end voltage in steps of 0.1 V when [TYPE B] is selected in the main menu → [BATTERY
SETUP] → [BATTERY SELECT].
The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC.
[11.0V]...[15.0V]
f Factory setting: [12.5V]
Selects the voltage for full display in steps of 0.1 V when [TYPE C] is selected in the main menu →
[BATTERY SETUP] → [BATTERY SELECT].
[13.0V]...[17.0V]
f Factory setting: [15.9V]
Selects the near end voltage in steps of 0.1 V when [TYPE C] is selected in the main menu → [BATTERY
SETUP] → [BATTERY SELECT].
[11.0V]...[15.0V]
f Factory setting: [13.2V]
Selects the end voltage in steps of 0.1 V when [TYPE C] is selected in the main menu → [BATTERY
SETUP] → [BATTERY SELECT].
[11.0V]...[15.0V]
f Factory setting: [12.5V]
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set for [TYPE A].
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
If a battery whose remaining charge is displayed in units of 10% is used, the setting value and actual near
end warning may vary slightly.
Selects the end percent value.
When the battery charge level percentage cannot be detected, this will follow the end voltage value set for
[TYPE A].
[1%]...[10%]
f Factory setting: [1%]
When using a battery which displays battery charge level by units of 10%, an end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] and [10%].
Selects the near end percent value.
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set for [TYPE A].
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
If a battery whose remaining charge is displayed in units of 10% is used, the setting value and actual near
end warning may vary slightly.
Selects the end percent value.
When the battery charge level percentage cannot be detected, this will follow the end voltage value set for
[TYPE A].
[1%]...[10%]
f Factory setting: [1%]
When using a battery which displays battery charge level by units of 10%, an end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] and [10%].
Loads scene files from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads scene files.
[SAVE]: Saves scene files.
Loads user files from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads user files.
[SAVE]: Saves user files.
Loads CAC files from an SD memory card or deletes CAC files stored in the SD memory card.
[LOAD]: Loads CAC files. Specifies the file number when saving a loaded CAC file in the SD memory card
to the camera.
[DELETE]: Deletes CAC files stored in the SD memory card.
– 137 –
Description of settings
Description of settings

Advertisement

Table of Contents
loading

Table of Contents