Bosch AutoDome Mounting Manual page 16

EN
CAUTION:
For a secure installation, use a minimum of six (6)
ν
10 mm ( 3 ⁄ -inch) diameter fasteners; three (3) on each side
8
of the mounting bracket. Use stainless steel
fasteners.
If bolts are used, they should extend through the mount-
ν
ing surface and be secured with flat washers, lock washers,
and nuts on the opposite side. Each bolt must have a min-
imum pullout strength of 275 kg
(600 lb).
If studs are used, they should be anchored in concrete or
ν
welded to a steel backer plate. Each stud must have a mini-
mum pullout strength 275 kg (600 lb).
If the wall mount is attached to wood or to a blind struc-
ν
ture (with no access to the rear), each fastener must have a
minimum pullout strength of 275 kg
(600 lb).
5.3.2.2 PARAPET WALL INSTALLATION
a. Determine the location of the unit on the wall.
Choose a location to allow the mounting bracket to be
placed as close as possible to the top of the wall. This will
allow the best chance for the AutoDome to clear the wall
when it is swung into position, and for
maintenance.
CAUTION: Allow enough room below the mounting
bracket for routing the camera and control tubes.
b. Using the wall mounting bracket as a template, position it
in the desired location and mark the hole locations on the
wall (see FIGURE 2). Use a minimum of six (6) fasteners
(not supplied): three (3) fasteners for each side of the
mounting bracket.
Pipe Arm
Wall Mount
3/8-16 SS
Hex Head Bolt
(supplied)
Figure 2 Installation of Wall Mount to a Wall
c. Prepare the mounting surface for the type of fasteners that
will be used by drilling holes or mounting anchors, etc. as
required.
© 2003 Bosch Security Systems
d. Apply a good quality sealant around each hole, anchor or
e. Install the mounting bracket and tighten all fasteners
f. After removing the pipe arm end cap, feed all electrical
g. Insert the pipe arm into the mounting bracket until it bot-
h. Apply thread sealant or pipe tape to the pipe threads to
8 fastener holes shown.
Use a minimum of
6 fasteners (not supplied).
i. Make all electrical connections. In some installations, lift-
j. Rotate the pipe arm to swing the AutoDome out from the
Apply sealant
around each
fastener hole.
CAUTION: Use six (6) 10 mm (
stainless steel fasteners (not supplied). Each
fastener must be able to withstand a minimum pull-
out force of 275 kg (600 lb).
stud at the mounting surface (see FIGURE 2).
securely.
and control cables through the pipe arm and out the bot-
tom of the mounting bracket.
toms.
prevent gapping and water leakage. Attach the AutoDome
to the pipe arm at the pipe thread.
End Cap with O-Ring
Pipe Arm
1/4 - 20 SS Cap Screw
10-24 SS Pan Head Screw
Figure 3 LTC 9230 with End Cap Removed
CAUTION: To prevent accidental loosening, the pipe
connection should be threaded until it is fully secure
(a minimum of four (4) complete turns).
Secure the AutoDome or housing according to the
instructions with that unit.
ing of the pipe arm may be required for the AutoDome to
clear the top of the wall when it is swung into position. Be
sure to allow enough cable slack to permit rotating the
pipe arm out over the roof and swinging it back again
when camera maintenance is required.
roof and into the desired position. Tighten the three (3)
10 mm ( 3 ⁄ -inch) stainless steel hex bolts
8
(provided; see FIGURE 2) to secure the pipe arm into
position.
CAUTION: Do not over tighten the bolts or stripping
of the threads may occur. Maximum torque is 34 N·m
(25 ft·lb).
Installation
3 ⁄ -inch) diameter
8
Page 16 of 24