1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Security Camera
  5. VEZ-5000
  6. Operation manual

Bosch VEZ-5000 Operation Manual

Analog ptz camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AUTODOME 5000 Analog PTZ Camera
VEZ-5000
en
Operations Manual

Advertisement

Table of Contents
loading

Related Manuals for Bosch VEZ-5000

Summary of Contents for Bosch VEZ-5000

  • Page 1 AUTODOME 5000 Analog PTZ Camera VEZ-5000 Operations Manual...

  • Page 3: Table Of Contents

    White Balance 6.10.2 Video Level 6.10.3 AutoSensUp Max 6.10.4 Exposure Mode 6.10.5 Backlight 6.10.6 Sharpness 6.10.7 WDR Function 6.10.8 Night Mode 6.10.9 Enhancement 6.10.10 6.11 Lens Setup 6.11.1 Auto Focus Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 4 Time Setting 6.13.5 Motion Track 6.14 Alarm Setup 6.14.1 Alarm Setting 6.14.2 Alarm Detect 6.15 Language 6.16 Installer Setup 6.16.1 System Setup 6.16.2 Camera Setting Operation Troubleshooting Technical data Appendices 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 5: Safety

    Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
  • Page 6 11. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 7: Important Notices

    16. Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warranty or, in the case of an authorization agreement, authority to operate the equipment.
  • Page 8 Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.

  • Page 9: Fcc And Ices Compliance (Class A)

    Cette appareil génère, utilise et émet de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux instructions, générer des Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 10 TV Interference Problems » (Comment identifier et résoudre les problèmes d’interférences de radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 11: Description

    4 Alarm Inputs, 2 Alarm Outputs ( N.C. / N.O./ OFF) – Multi-language On-Screen Display – Bosch OSRD, Pelco P/D Protocol – Compatible external devices ( LTC-5136,MIC-BP3, UPA-2450-50 / UPA-2450-60) – Programmable PTZ Speed: Proportional to Zoom ratio, changeable preset speed Bosch Security Systems, Inc.

  • Page 12: Unpacking

    Parts List Quanity Graphic Description Mounting Adapter Dome Camera Body without Sunshield Dome Camera Body with Sunshield M5x8L security screw for mounting adapter T20 Security Torx wrench for M5x8L security screw 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 13 T10 Security Torx wrench for dome bubble Lubricant User Manual Notice! 1. Your package contains one Dome Camera Body, depending if you purchased an indoor (without sunshield) or an outdoor (with sunshield) camera. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 14: Installation

    1.2 km if the used cables are not the CAT 5, 24-gauge cables. Refer to section RS-485. For detailed information about the repeater, refer to its manual. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 15: Connection

    Refer to the diagram and table below for positions and definition of the switches / connectors. Letter Description Alarm I/O Camera ID setup dip switch BNC video output Communication switch Camera control protocol switcher RS-485 connector Power connector Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 16: Communication Switch Setting

    SETTING> to assign the camera’s ID number. Refer to the section Camera Setting for detail setting instructions. Notice! No two cameras in the same network should be given the same ID, or communication conflict may occur. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 17: Camera Control Protocol Setting

    Choose an appropriate protocol for the camera. Switch Protocol Baud Rate Number Pelco D 2400 Pelco D 4800 Pelco D 9600 Pelco P 1200 Pelco P 4800 Pelco D 9600 Bosch OSRD 9600 Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 18: Power Connector

    Refer to the pin definition table below for alarm system wiring. ALARM_OUT_NO_1 ALARM_OUT_COM_2 ALARM_OUT_NC_1 ALARM_OUT_COM_1 ALARM_IN_4 ALARM_IN_3 ALARM_OUT_NO_2 ALARM_IN_2 ALARM_OUT_CN_2 ALARM_IN_1 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 19: Rs-485 Connector Definition

    AUTODOME 5000 Analog PTZ Camera Connection | en RS-485 Connector Definition Before connecting the RS-485 wires, refer to the illustrations below for definition of the RS-485 connector. RS-485 Connector Switch Descriptio Number Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 20: Prepare The Camera For Assembly

    If the Dome Camera will be attached to a wall or a pipe mount, ensure that the Indoor Adaptor is attached to the wall or pipe mount prior to attaching the Camera Dome Body. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 21: Assemble The Outdoor Camera

    1 M5x8L Mechanical Screw with Spring 4 Sunshield Washer (1 piece) 2 Outdoor Adaptor 5 Camera Body 3 M4x21L Mechanical Screw with Spring 6 Bubble Washer (3 pieces) 7 M3x23L Screws with Rubber (2 pieces) Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 22: Accessories

    TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS, UNLESS YOU ARE QUALIFIED TO DO In USA and Canada, use Class 2 power supply unit (PSU) only. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 23 AUTODOME 5000 Analog PTZ Camera Connection | en Notice! Use of Grounded Conduit A grounded conduit is required in order to meet the EMC Regulation Requirements. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 24: On-Screen Display (Osd) Menu

    NTSC: <1/60> to <1/1000> sec. Iris Value <1> to <17> Gain Control <1> to <16> Backlight ON, OFF Sharpness <01> to <16> WDR Function ON, OFF Night Mode Threshold High, Mid, Low 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 25 On-Screen Display (OSD) Menu | en SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE Night Mode Auto, On, Off Enhancement Zoom, Stabilize, Off 2D N.R. On, Off 3D N.R. On, Off Restore Defaults Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 26: Lens Setup Menu

    | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Lens Setup Menu SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE Auto Focus Constant Manual Spot Digital Zoom <Off> <2x> to <12x> Restore Defaults Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 27: Ptz Setup Menu

    Home Setting Home Function On, Off Select Mode Preset, P. Tour, Autopan, Tour Preset Point <1> to <99> Preset Tour <1> to <8> Autopan <1> to <4> Tour <1> to <8> Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 28 Min Angle <-10> to <+10> Max Angle <80> to <100> PT Position PT Display On, Off Set Pan Zero Enter Speed By Zoom On, Off AutoCali On, Off Restore Defaults Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 29: Display Setup Menu

    Set Hour <00> to <23> Set Minute <00> to <59> Motion Track Motion Track On, Off Motion Block On, Off Bounding Box On, Off Threshold <1> to <255> Restore Defaults Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 30: Alarm Setup Menu

    Frame Set <01> to <04> Left Limit Top Limit H. Size V. Size Mode Preset, P. Tour, Tour, Autopan Frame Disable <01> to <04> Threshold <001> to <255> Restore Defaults Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 31: Language Setup Menu

    AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en Language Setup Menu SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE ZH-ZN Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 32: Installer Menu

    ID Number <01> to <99> Title Setting Enter Protocol OSRD, Pelco P, Pelco D Baud Rate <2400>, <4800>, <9600> ID Info. ID Number, Title, Protocol, Baud Rate Restore Defaults Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 33: Monitor Display

    TILT ERROR / CAM MODULE ERROR Zoom Ratio Present Zoom Ratio (Optical Zoom/Digital Zoom) Title Maximum 20 characters for each title. 16 sets of title are available. Camera ID Camera ID Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 34 When the camera is starting up, the OSD Start Page will display information including ID number, protocol / baud rate, and camera initializing message. When any camera error occurs, the error message(s) will be shown on the screen. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 35: Main Menu

    MENU on your monitor by pressing the keys [95] + [Preset], or by pressing and holding the [Menu] key for 2 seconds. When you use Bosch OSRD protocol with your controller, you can access the MAIN MENU on your monitor by pressing the keys [ON]+[46]+[Enter].

  • Page 36: Common Menus

    Exit the menu. Restore Defaults The RESTORE DEFAULTS menu is for restoring the settings in any of the menus to the factory default values. Select <YES> to reset the parameters. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 37: Camera Setup

    3000K to 7500K. Indoor 3200 K Base mode. Outdoor 5800 K Base mode. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 38: Video Level

    Shutter speed (1/10000 to 1/50 for PAL; 1/10000 to 1/60 for NTSC) – Iris value <1> to <17> (F1.6 to F28) – Gain control <1> to <16> (−3 dB to 28 dB) 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 39: Backlight

    If you select <OFF>, digital zoom and Image Enhancement are deactivated. 6.10.10 In this menu, you can select the parameters for Dynamic Noise Reduction (DNR): 2DNR or 3DNR. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 40: Lens Setup

    Digital zoom takes a portion of an image and expands the partial image to the full size of the original image. Therefore, the image quality will be reduced. 6.12 PTZ Setup The PTZ Setup menu is as shown below: PTZ SETUP AUTOPAN TOUR PRESET TOUR PRESET FREEZE 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 41: Autopan

    <RIGHT> is selected here, and then return to the start point. The camera will start to pan anti-clockwise from the start point to the end point if the selection is <LEFT>. Refer to the diagram below. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 42: Tour

    Tour is a route formed with manual operation, through adjusting pan, tilt position and zoom parameters, which can be stored and recalled to execute repeatedly. TOUR Tour Record Start Enter Record End Enter 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 43: Preset Tour

    Preset Tour There are eight sets of preset tour built in the camera. Use the LEFT/RIGHT direction keys to select a set first and then set its preset tour points. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 44: Preset

    You can execute the Preset Tour function through a control keyboard. Refer to the control keyboard’s quick guide for further information. 6.12.4 Preset You can define preset points in this menu. PRESET Preset Set Preset Run Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 45 <CAMERA MENU> key again. Notice! You can set preset points through a control keyboard. Refer to the control keyboard’s quick guide for further information. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 46: Freeze

    Select a tour line that the camera should execute after the Return Time function is activated. The tour line(s) should be defined prior either in the TOUR setup menu or through the keyboard. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 47: Schedule

    If < NIGHT MODE > is selected, the Night Mode function is activated for a schedule point. – Tracking You can select <MOTION TRACK> as an action carried out in a schedule point. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 48: Misc. Function

    Calibration function is enabled, the camera will automatically detect the matter and reset the horizontal point back to the original position. 6.13 Display Setup The Display Setup menu is as shown below: 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 49: Id Display

    Access the OSD and go to <DISPLAY SETUP> → <TITLE DISPLAY> →<TITLE SETTING>. Select a number to represent the position. Press the <CAMERA MENU> key on the keyboard to access the editing page. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 50: Privacy Masking

    Color Black Set Masking Clear Masking Exit Privacy Switch You can enable or disable the Privacy Masking function through this item. Set this item to <ON> before configuring mask zones. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 51: Time Setting

    Select <ON> to enable the display of time information on the screen, or select <OFF> to disable. Set Year / Month / Day These items are for setting up the system date. Set Hour / Minute These items are for setting up the system time. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 52: Motion Track

    (N.O. or N.C.). With this function, the camera can work with the alarm system to catch event videos. For information about wiring, refer to the Installation section and/or to qualified service personnel. Adjustable alarm parameters are as listed below: 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 53 Use this option to enable (ON) or disable (OFF) the selected alarm pin. Alarm Type There are two different alarm types: Normally Open and Normally Closed, which are illustrated below. Select an alarm type that corresponds with the alarm application. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 54 Select a preset tour line that the camera should execute when the alarm pin is triggered. The preset tour line(s) should be defined prior either in the PRESET TOUR setup menu or through the keyboard. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 55: Alarm Detect

    This item is used to enable (ON) or disable (OFF) the Motion Detection function. The Motion Detection function allows the camera to monitor for suspicious motion and trigger an alarm when motion volume in the detection area exceeds the specified sensitivity threshold value. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 56 If any other mode (PRESET TOUR / AUTOPAN / TOUR) is selected, the camera will keep executing the selected mode (DWELL TIME: ALWAYS) until the alarm condition is released or you rotate the joystick to change the status of the camera. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 57: Language

    System Setup is where installers can set up system-related parameters, which are as follows. SYSTEM SETUP System Reset Enter Password Image Inverse Flip Enter OSD Auto Close 20 Sec Exit System Reset Two types of system reset can be implemented under this submenu. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 58 You can select <ON> to make the displayed image inversed vertically and horizontally (see the figures shown below). Occasions to employ the function include conferences, demonstration, testing, etc. The default setting is <OFF>. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 59 Preset Tour) is set in the position that can only be reached through the FLIP motion, the position will become unreachable when the Flip function is disabled. – Select this item to disable the flip function. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 60: Camera Setting

    ID Number Select the ID number. The default is 001. – Title Setting Set up the title for the camera. – Protocol Select OSRD, Pelco D, Pelco P. – Baud Rate 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 61 Select the correct baud rate: 2400, 4800, and 9600 ID Info. Displays the information about the camera ID, ID number, title, protocol, and baud rate. ID INFO. ID Number Title Protocol OSRD Baud Rate 9600BPS Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 62: Operation

    | Operation AUTODOME 5000 Analog PTZ Camera Operation The following tables identify common Aux commands (hot keys) for Bosch protocol and for Pelco protocol. Hot Keys, Bosch Protocol Preset Command / Description Example Function Autopan without On/Off Autopan - to pan 360º...
  • Page 63 Restores all settings to original defaults and Set+899+Enter clears all user-programmed settings Autopan left limit Save AutoPan left limit Set+101+Enter ( = manual preset) Autopan right limit Save AutoPan right limit Set+102+Enter ( = manual preset) Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 64 93+Preset ENT2 Key Preset No. + Preset 94+Preset MENU Key / Enter OSD menu Preset / **Menu 95 No. + Preset 95+Preset Deactivate running Autopan Preset No. + Preset 96+Preset 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 65 AUTODOME 5000 Analog PTZ Camera Operation | en Preset Preset Operation Example Number D.Zoom ( toggle) Preset No. + Preset 97+Preset Run Autopan #1 Preset No. + Preset 99+Preset Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 66: Troubleshooting

    - Check to see if the camera faces directly into the sun or a screen flickers. fluorescent lamp. If so, reposition the dome. - Check for flickers on the screen. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 67 I see only one with the same priority number are triggered simultaneously, the triggered. system gives higher priority to the alarm with the smaller number, and handles only that alarm. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...

  • Page 68: Technical Data

    AUTODOME 5000 Analog PTZ Camera Technical data Camera Dimensions (7.36) (in.) (8.19) Figure 9.1: AUTODOME 5000 Indoor/Outdoor Dimensions 1 Diameter without sunshield (indoor models) 2 Diameter with sunshield (outdoor models) 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.

  • Page 69: Appendices

    AUTODOME 5000 Analog PTZ Camera Appendices | en Appendices The following tables list the DIP Switch settings for camera IDs. ID Number SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 Sw-9 SW-10 Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 70 | Appendices AUTODOME 5000 Analog PTZ Camera ID Number SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 Sw-9 SW-10 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 71 AUTODOME 5000 Analog PTZ Camera Appendices | en ID Number SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 Sw-9 SW-10 Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.3 |...
  • Page 72 SW-6 SW-7 SW-8 Sw-9 SW-10 Table 10.1: Camera ID Setup – DIP Switch Settings Protocol Number SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 Table 10.2: Protocol Setup – DIP Switch Settings 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
  • Page 74 Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA, 17601 www.boschsecurity.com © Bosch Security Systems, Inc., 2014...

This manual is also suitable for:

Autodome 5000

Table of Contents