Denon AVR-4311 Owner's Manual page 97

Setting items
Distance Meters / Feet : Set the unit of distance.
Set distance from listening
Step : Set the minimum variable width of the distance.
position to speakers.
• 0.1m / 0.01m
Measure beforehand the
• 1ft / 0.1ft
distance from the listening
Default : The "Distance" settings are returned to the default settings.
position to each speaker.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
to the default?" prompt is displayed. Select either "Yes" or "No", and
ENTER
press
Front L / Front R / Center / Subwoofer / Subwoofer 1
2 / Surr.L / Surr.R / Surr.Back L
z
2
L / Front Height R / Front Wide L / Front Wide R : Select the speaker.
z1 When the "Speaker Config." – "Subwoofer" setting (vpage 92) is
set to "2 spkrs", "Subwoofer 1" and "Subwoofer 2" are displayed.
z2 When the "Speaker Config." – "Surround Back" setting (vpage 92)
is set to "1 spkr", "Surround Back" is displayed.
• 0.00m – 18.00m / 0.0ft – 60.0ft : Set the distance.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 91) and "Speaker Config." (vpage 91) settings.
• Default settings :
Front L / Front R / Center / Subwoofer / Subwoofer 1 / Subwoofer 2 /
Front Height L / Front Height R / Front Wide L / Front Wide R : 3.6 m
(12.0 ft)
Surr. L / Surr. R / Surr.Back L / Surr.Back R : 3.0 m (10.0 ft)
• Set the difference in the distance between the speakers to less than 6.0
m (20.0 ft).
NOTE
Speakers set to "None" in "Speaker Config." (vpage 91) are not
displayed.
Remote control operation
buttons
Setting details
ENTER
, the "Return all settings
.
1 / Subwoofer
z
2 / Surr.Back R 2 / Front Height
z z
Move the cursor
(Up/Down/Left/Right)
Setting items
Channel Level Test Tone : Output test tone.
Set the volume of the test • Front L / Front Height L / Center / Front Height R / Front R / Front
tone to be the same when it Wide R / Surround R / Surr.Back R
is output from each speaker. L / Front Wide L / Subwoofer / Subwoofer 1
Subwoofer 1+2
z1 When the "Speaker Config." – "Surround Back" setting (vpage 92)
is set to "1 spkr", "Surr.Back" is displayed.
z2 When the "Speaker Config." – "Subwoofer" setting (vpage 92) is
set to "2 spkrs", "Subwoofer 1", "Subwoofer 2" and "Subwoofer
1+2" are displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• After aligning both the distances and levels of subwoofer 1 and
subwoofer 2, please adjust subwoofer 1+2. These parameters affects
the volume of subwoofer 1+2.
• By clicking o p
moves down or up together.
• If one of subwoofer1 or subwoofer 2 reaches ±12.0 dB, then the cursors
don't move further.
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 62.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 91) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Confirm the setting
MANUAL SETUP
Setting details
1 / Surr.Back L 1 / Surround
z z
2 / Subwoofer 2
z
2 : Select the speaker.
z
, the volume of both subwoofer 1 and subwoofer 2
Return to previous menu
ENGLISH
2 /
z
93