O N - S C R E E N R E P O R T Vi E W; P R I N T I N G R E P O R T S - Alto-Shaam quickchiller QC-3 Operating Procedure Manual

EXAMPLE: ACHILL . . . . . . . . . .Auto-Chill
TCHILL . . . . . . . . . .Timed-Chill
HOLD . . . . . . . . . . .Holding
The third line also shows the number of lines (samples)
recorded (30) and the time (in minutes) between samples.
The last line on the screen informs the operator the
"A" and "B" buttons will scroll through the reports in
memory, the "C" button will display the Print Report
screen, and the "D" button will cancel the display and
return to the Main Menu screen.

6 . 4 O n - S c r e e n R e p o r t Vi e w

If a report has at least 3 samples, it is possible to
view sample times and temperatures on the display
without using a printer. To view the contents of a
report, press "0" on the keyboard when the Report
Selection screen is displayed. A View Report screen
will appear in the display.
V I E W R E P O RT S C R E E N
1 5 3 0 0 5 0
1 5 3 5 0 4 7
1 5 4 0 0 4 5
A = U P B = D N
The 4 digits in the first column represent the time
of day the sample was recorded; 1530 = 15:30 hours or
3:30 PM. The remaining columns indicate the
temperatures of the food product probes in the upper,
middle, and lower positions along with the air
temperature within the cabinet.
The percentage figure in the lower right of the
display indicates the amount of the report that has
been viewed. In other words, if the above report
contains 30 samples, and the first three samples are
displayed, 10% of the report has been viewed by the
operator. By pressing "A" or "B" on the keyboard the
report will scroll in increments of 3 samples. As the
report continues to scroll, the percentage will change
with 50% indicating the 3 middle lines and 100%
indicating the last three lines of the report are in view.
Press "C" to cancel and return to the Report
Selection screen.
0 5 4 0 5 6 0 4 8
0 5 0 0 5 2 0 4 2
0 4 8 0 5 0 0 4 0
C = C A N 0 1 0 %
quickchiller
-
A LT O S H A A M

6 . 5 P r i n t i n g R e p o r t s

R e p o r t s c a n b e p r i n t e d t o a 4 0 , 8 0 , o r a 1 3 2
column printer. The chiller hardware is configured
at the factory for either a parallel or serial printer
(not both).
W h e n a n o r d e r f o r a c h i l l e r i s p l a c e d , t h e
type of printer that will be used must also
b e s p e c i f i e d s o t h a t t h e c h i l l e r h a r d w a r e
c a n b e p r o p e r l y c o n f i g u r e d a t t h e f a c t o r y.
Serial printers are recommended because they
are smaller and easier to handle, however, a
parallel printer is also acceptable.
PREPARATION FOR PRINTING REPORTS
(Refer to Section 9.0 for additional information)
1. Connect printer to the power source.
2. Connect printer cable to printer.
3. Connect printer cable to the chiller control. The
i n t e r f a c e f o r t h e c h i l l e r c a b l e c o n n e c t i o n i s
l o c a t e d i n t h e s l i d e - b y a c c e s s p a n e l a t t h e
b o t t o m o f t h e Q u i c k c h i l l e r m i c r o p r o c e s s o r
control panel.
To print a report following proper connection to
the printer, press "D" on the keyboard when the
Main Menu screen is displayed.
To access the Print Report screen, press "C"
o n t h e k e y b o a r d w h e n t h e R e p o r t S e l e c t i o n
Screen is displayed.
P R I N T R E P O RT S C R E E N
C O N N E C T P R I N T E R T H E N
S TA R T P L O T T I N G . . . . . . . B
S TA R T P R I N T I N G . . . . . . . . C
C A N C E L . . . . . . . . . . . . . . D
Select the type of report required. Press "C" on the
k e y b o a r d t o p r i n t t h e r e p o r t a s a t a b l e o f
temperatures. Press "B" to print the report as a
graph. Press "D" to cancel the Print Report screen
and return to the Report Selection screen display.
™ O P E R AT I O N A N D P R O C E D U R E G U I D E
O P E R AT I O N
Pg. 9