Table of Contents
Advertisement
CS9350 INSTALLATION MANUAL
3.3
Detaching protective materials
This product has protective materials in the place
shown below.
Detach all protective materials in accordance with the
following steps.
1. Remove all tapes from each cover.
2. Open the front cover and remove the CR belt clip
from the CR belt.
2
1
No.
Name
No.
1
CR belt
2
This completes detaching protective materials.
・
4 Installation
Procedures and environment for installing this product
are explained.
4.1
Installation environment
Install this product to the appropriate place with refer-
ence to the following.
WARNING
Do not install the printer in the follow-
ing places where there is a possibility
that the printer may be damaged or
might fall or be fallen by chance
On a shaky stand
Slanting location
Places where vibration of other machines
etc. is transmitted
.
Do not stamp on the printer or do not
place heavy things on top of it. The
printer may be damaged or might fall
or be fallen by chance
.
Cover the printer with blanket and
cloth like tablecloth and do not close
the vent. If the vent is closed, the print-
er could accumulate heat inside and
may cause fire .
Do not install the printer in a location
that has high humidity or is dusty.
It could lead to electric shock and fire
AP-40800 - 1.0
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
Floor strength of
installation place
Power
Power
Specifica-
Supply
tion
Frequency
Range
Power
capacity
Environm-
Operative
ental
condition
conditions
Guaranteed
range of
printing
accuracy
Change
rate
NOTE
For temperature and humidity, avoid locations
Name
such as the following. There is a possibility that
CR belt clip
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illu-
mination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant, in-
stall this product in a location where the air condi-
tion is adjustable.
4.1.2 Installation space
Install on a level floor which meets the following con-
dition.
・It has enough strength to support the weight of the
printer and the stand.
NOTE
For the weight of the printer and the stand, refer to
the Operation Manual.
a=500mm
b=1000mm
c=1000mm
d=1000mm
e=1440mm
f=3000mm
g=2660mm
.
a
f
4.2 Installation procedure
Install this product to the installation place in accord-
ance with the list shown below.
NOTE
Please check that the butterfly bolts are not loose
before/after carrying this product.
When transferring or carrying outside, separate the
printer and the stand.
1. Check that the two butterfly bolts attaching the
.
stand and the printer are not loose.
2. Carry the printer to the installation place.
More than 2940 Pa (300 kg/m
)
2
AC90V - 132V/198V - 264V
50/60Hz ± 1Hz
More than 10 A
Temperature:20 °C to 32 °C
Humidity: 40 % to 60 %, No Condensation
Temperature:22 °C to 30°C
Humidity: 40 % to 60 %
Temperature: within 2 °C per hour
Humidity: within 5 % per hour
e
d
b
c
g
4
3. Lock two casters on the front side.
1
2
No.
Name
No.
1
Casters
2
4. Check that the two butterfly bolts attaching the
stand and the printer are not loose.
5. Confirm that the waste fluid valve is closed.
1
No.
Name
1
Waste fluid valve
5 Connecting the power cable
This section explains how to connect the power cable.
WARNING
Be sure to use the specified power ca-
ble(separately sold)
.
Using power cables other than the
specified can cause an electric shock
or fire .
Use a power cord set which is compati-
ble with the safety standards, power
supply voltage, and plug shape used
in the country where this printer is
used .
Use a power cord set which is equip-
ped with a protective earth, and se-
curely connect it to the outlet
Do not use a damaged power cable. It
may cause an electric shock or fire
Follow the steps below to connect the power cable.
1. Confirm that the product is turned OFF.
NOTE
If the [Power] key is pressed, the product is turned
ON. Press the key again, and turn OFF the power.
Name
Caster locks
.
.
Advertisement
Table of Contents
